- Device configuration via plain text config file. Also able to operate
when not attached to the chip as the master driver.
- Generic "work request" queue that serves as the base for both ctrl and
ofld tx queues.
- Generic interrupt handler routine that can process any event on any
kind of ingress queue (via a dispatch table).
- A couple of new driver ioctls. cxgbetool can now install a firmware
to the card ("loadfw" command) and can read the card's memory
("memdump" and "tcb" commands).
- Lots of assorted information within dev.t4nex.X.misc.* This is
primarily for debugging and won't show up in sysctl -a.
- Code to manage the L2 tables on the chip.
- Updates to cxgbe(4) man page to go with the tunables that have changed.
- Updates to the shared code in common/
- Updates to the driver-firmware interface (now at fw 1.4.16.0)
MFC after: 1 month
This patch should remove the need for kldunload of USB
controller drivers at suspend and kldload of USB controller
drivers at resume.
This patch also fixes some build issues in avr32dci.c
MFC after: 2 weeks
Tested on Qemu/KVM, VirtualBox, and BHyVe.
Currently built as modules-only on i386/amd64. Man pages not yet hooked
up, pending review.
Submitted by: Bryan Venteicher bryanv at daemoninthecloset dot org
Reviewed by: bz
MFC after: 4 weeks or so
based on Solarflare SFC9000 family controllers. The driver supports jumbo
frames, transmit/receive checksum offload, TCP Segmentation Offload (TSO),
Large Receive Offload (LRO), VLAN checksum offload, VLAN TSO, and Receive Side
Scaling (RSS) using MSI-X interrupts.
This work was sponsored by Solarflare Communications, Inc.
My sincere thanks to Ben Hutchings for doing a lot of the hard work!
Sponsored by: Solarflare Communications, Inc.
MFC after: 3 weeks
results in the HAL being built without HAL debugging/diagnostic support,
the module building process needs to be somehow taught to not build AR5416+
NICs if AH_SUPPORT_AR5416 isn't defined in opt_ah.h .
This implies that users who are building the driver do so with
KERNBUILDDIR set to the compile/CONFIG directory so the various
opt_* sources can be pulled in.
compiled into the kernel.
Do not try to build the module in case of no INET support but
keep #error calls for now in case we would compile it into the
kernel.
This should fix an issue where the module would fail to enable
IPv6 support from the rc framework, but also other INET and INET6
parts being silently compiled out without giving a warning in the
module case.
While here garbage collect unneeded opt_*.h includes.
opt_ipdn.h is not used anywhere but we need to leave the DUMMYNET
entry in options for conditional inclusion in kernel so keep the
file with the same name.
Reported by: pluknet
Reviewed by: plunket, jhb
MFC After: 3 days
replace amd(4) with the former in the amd64, i386 and pc98 GENERIC kernel
configuration files. Besides duplicating functionality, amd(4), which
previously also supported the AMD Am53C974, unlike esp(4) is no longer
maintained and has accumulated enough bit rot over time to always cause
a panic during boot as long as at least one target is attached to it
(see PR 124667).
PR: 124667
Obtained from: NetBSD (based on)
MFC after: 3 days
take advantage of it instead of duplicating it. This reduces the size of
the i386 GENERIC kernel by about 4k. The only potential in-tree user left
unconverted is xe(4), which generally should be changed to use miibus(4)
instead of implementing PHY handling on its own, as otherwise it makes not
much sense to add a dependency on miibus(4)/mii_bitbang(4) to xe(4) just
for the MII bitbang'ing code. The common MII bitbang'ing code also is
useful in the embedded space for using GPIO pins to implement MII access.
- Based on lessons learnt with dc(4) (see r185750), add bus barriers to the
MII bitbang read and write functions of the other drivers converted in
order to ensure the intended ordering. Given that register access via an
index register as well as register bank/window switching is subject to the
same problem, also add bus barriers to the respective functions of smc(4),
tl(4) and xl(4).
- Sprinkle some const.
Thanks to the following testers:
Andrew Bliznak (nge(4)), nwhitehorn@ (bm(4)), yongari@ (sis(4) and ste(4))
Thanks to Hans-Joerg Sirtl for supplying hardware to test stge(4).
Reviewed by: yongari (subset of drivers)
Obtained from: NetBSD (partially)
drivers that only ever attach to a particular MAC driver, i.e. inphy(4),
ruephy(4) and xlphy(4), to the directory where the respective MAC driver
lives and only compile it into the kernel when the latter is also there,
also removing it from miibus.ko and moving it into the module of the
respective MAC driver.
- While at it, rename exphy.c, which comes from NetBSD where the MAC driver
it corresponds to also is named ex(4) instead of xl(4) but that in FreeBSD
actually identifies itself as xlphy(4), and its function names accordingly
for consistency.
- Additionally while at it, fix some minor style issues like whitespace
in the register headers and add multi-inclusion protection to inphyreg.h.
thanks for their contiued support to FreeBSD.
This is version 10.80.00.003 from codeset 10.2.1 [1]
Obtained from: LSI http://kb.lsi.com/Download16574.aspx [1]
build the ip_fw_pfil.c hooks and ipfw even in case of no-ip under the
assumption that the private L2 hook (which hopefully eventually will be a
pfil hook as well) can still be useful.
Allow building the module without inet as well.
Glanced at by: jhb
MFC after: 3 days
build it with and without INET/INET6 support.
Submitted by: Alexander V. Chernikov <melifaro at yandex-team.ru> [1]
Tested by: Alexander V. Chernikov <melifaro at yandex-team.ru> [1]
Approved by: re (bz)
MFC after: 2 weeks
options defined in the kernel config. This more closely matches the
behavior of other modules which inherit configuration settings from the
kernel configuration during a kernel + modules build.
Reviewed by: luigi
Approved by: re (kib)
MFC after: 1 week
improvements:
(1) Implement new model in previously missed at91 UART driver
(2) Move BREAK_TO_DEBUGGER and ALT_BREAK_TO_DEBUGGER from opt_comconsole.h
to opt_kdb.h (spotted by np)
(3) Garbage collect now-unused opt_comconsole.h
MFC after: 3 weeks
Approved by: re (bz)
(1) opt_capsicum.h is no longer required in ffs_alloc.c, so remove the
#include.
(2) portalfs depends on opt_capsicum.h, so have the Makefile generate one
if required.
These affect only modules built without a kernel (i.e, not buildkernel,
but yes buildworld if the dubious MODULES_WITH_WORLD is used).
Approved by: re (bz)
Sponsored by: Google Inc
the NFS subsystems use five of the rpcsec_gss/kgssapi entry points,
but since it was not obvious which others might be useful, all
nineteen were included. Basically the nineteen entry points are
set in a structure called rpc_gss_entries and inline functions
defined in sys/rpc/rpcsec_gss.h check for the entry points being
non-NULL and then call them. A default value is returned otherwise.
Requested by rwatson.
Reviewed by: jhb
MFC after: 2 weeks
cloned from the old NFS client, plus additions for NFSv4. A
review of this code is in progress, however it was felt by the
reviewer that it could go in now, before code slush. Any changes
required by the review can be committed as bug fixes later.
This is in no way a complete DFS/radar detection implementation!
It merely creates an abstracted interface which allows for future
development of the DFS radar detection code.
Note: Net80211 already handles the bulk of the DFS machinery,
all we need to do here is figure out that a radar event has occured
and inform it as such. It then drives the DFS state engine for us.
The "null" DFS radar detection module is included by default;
it doesn't require a device line.
This commit:
* Adds a simple abstracted layer for radar detection state -
sys/dev/ath/ath_dfs/;
* Implements a null DFS module which doesn't do anything;
(ie, implements the exact behaviour at the moment);
* Adds hooks to the ath driver to process received radar events
and gives the DFS module a chance to determine whether
a radar has been detected.
Obtained from: Atheros
filters working. (All other filters - switch without L2 info rewrite,
steer, and drop - were already fully-functional).
Some contrived examples of "switch" filters with L2 rewriting:
# cxgbetool t4nex0 iport 0 dport 80 action switch vlan +9 eport 3
Intercept all packets received on physical port 0 with TCP port 80 as
destination, insert a vlan tag with VID 9, and send them out of port 3.
# cxgbetool t4nex0 sip 192.168.1.1/32 ivlan 5 action switch \
vlan =9 smac aa:bb:cc:dd:ee:ff eport 0
Intercept all packets (received on any port) with source IP address
192.168.1.1 and VLAN id 5, rewrite the VLAN id to 9, rewrite source mac
to aa:bb:cc:dd:ee:ff, and send it out of port 0.
MFC after: 1 week
Some files keep the SUN4V tags as a code reference, for the future,
if any rewamped sun4v support wants to be added again.
Reviewed by: marius
Tested by: sbruno
Approved by: re
Reference code that shows how to get a packet's timestamp out of
cxgbe(4). Disabled by default because we don't have a standard way
today to pass this information up the stack.
The timestamp is 60 bits wide and each increment represents 1 tick of
the T4's core clock. As an example, the timestamp granularity is ~4.4ns
for this card:
# sysctl dev.t4nex.0.core_clock
dev.t4nex.0.core_clock: 228125
MFC after: 1 week
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
- 77115: Implement support for O_DIRECT.
- 98425: Fix a performance issue introduced in 70131 that was causing
reads before writes even when writing full blocks.
- 98658: Rename the BALLOC flags from B_* to BA_* to avoid confusion with
the struct buf B_ flags.
- 100344: Merge the BA_ and IO_ flags so so that they may both be used in
the same flags word. This merger is possible by assigning the IO_ flags
to the low sixteen bits and the BA_ flags the high sixteen bits.
- 105422: Fix a file-rewrite performance case.
- 129545: Implement IO_INVAL in VOP_WRITE() by marking the buffer as
"no cache".
- Readd the DOINGASYNC() macro and use it to control asynchronous writes.
Change i-node updates to honor DOINGASYNC() instead of always being
synchronous.
- Use a PRIV_VFS_RETAINSUGID check instead of checking cr_uid against 0
directly when deciding whether or not to clear suid and sgid bits.
Submitted by: Pedro F. Giffuni giffunip at yahoo
The AR9130 is an AR9160/AR5416 family WMAC which is glued directly
to the AR913x SoC peripheral bus (APB) rather than via a PCI/PCIe
bridge.
The specifics:
* A new build option is required to use the AR9130 - AH_SUPPORT_AR9130.
This is needed due to the different location the RTC registers live
with this chip; hopefully this will be undone in the future.
This does currently mean that enabling this option will break non-AR9130
builds, so don't enable it unless you're specifically building an image
for the AR913x SoC.
* Add the new probe, attach, EEPROM and PLL methods specific to Howl.
* Add a work-around to ah_eeprom_v14.c which disables some of the checks
for endian-ness and magic in the EEPROM image if an eepromdata block
is provided. This'll be fixed at a later stage by porting the ath9k
probe code and making sure it doesn't break in other setups (which
my previous attempt at this did.)
* Sprinkle Howl modifications throughput the interrupt path - it doesn't
implement the SYNC interrupt registers, so ignore those.
* Sprinkle Howl chip powerup/down throughout the reset path; the RTC methods
were
* Sprinkle some other Howl workarounds in the reset path.
* Hard-code an alternative setup for the AR_CFG register for Howl, that
sets up things suitable for Big-Endian MIPS (which is the only platform
this chip is glued to.)
This has been tested on the AR913x based TP-Link WR-1043nd mode, in
legacy, HT/20 and HT/40 modes.
Caveats:
* 2ghz has only been tested. I've not seen any 5ghz radios glued to this
chipset so I can't test it.
* AR5416_INTERRUPT_MITIGATION is not supported on the AR9130. At least,
it isn't implemented in ath9k. Please don't enable this.
* This hasn't been tested in MBSS mode or in RX/TX block-aggregation mode.
