locked. This is intended primarily to support the userland equivalent
of the various *_ASSERT_LOCKED() macros we have in the kernel.
MFC after: 2 weeks
referencing the files VM pages are returned from the network stack,
making changes to the file safe.
This flag does not guarantee that the data has been transmitted to the
other end.
- Rename rt2560_read_eeprom to rt2560_read_config, we already have
rt2560_eeprom_read
- If hardware gives us wrong encryption done index, shout out loudly and
terminate the processing loop
- Process encryption done if RX done bit is set in interrupt status register
(according to Ralink Linux driver)
- Turn VALID/BUSY bits in TX descriptor only after TX descriptor is fully setup
- Fix BBP read: RT2560_BBPCSR can't be written until its RT2560_BBP_BUSY bit is
off (according to Ralink Linux driver)
- Skip invalid (0 of 0xffff) BBP register/value entries stored in EEPROM
- Fix channel TX power location in EEPROM, if channel TX power is above 31 set
it to 24 (TX power only has 5bits in RF register, "24" is according to Ralink
Linux driver)
- Configure BBP according to the BBP register/value stored in EEPROM, restore
BBP17 (RX sensitivity tuning) to default value after this.
- Set TX/RX antenna after BBP is initialized; these two operation will try to
set BBP registers
- Reconfigure ACK TX time registers according to 802.11g standard (TX @36Mb,
other side's ACK should be sent @24Mb).
- 2560 parts have two TX ring: one for management/control packets, one for data
packets. Add private OACTIVE flag for each of them. Turn on IFF_DRV_OACTIVE
if one of private OACTIVE is on; turn off IFF_DRV_OACTIVE iff all of them are
off.
- Rework watchdog to mimic old if_watchdog action. Process TX done/encryption
done in watchdog function (according to Ralink Linux driver)
Obtained from: DragonFly
Approved by: sam (mentor)
Tested by: sam
Related to PR: kern/117655
# Forcing long slot time setting is not included in this commit, comment and
# related code is in place, so if problem pops up, quick tests could be done.
were recently), a simple 'make cleandepend; make depend' is sufficient
to keep the tree buildable after a cvs update when doing incremental
builds.
However, kdump and truss use a script which searches for header files
that define ioctls, and generates C code that includes them. This
script will usually not need updating when a header file is removed,
so the normal dependency mechanism will not realize that it needs to
be re-run. One is therefore left with code that references dead files
but will only be removed by a full 'make clean', which defeats the
purpose of incremental builds.
To work around this, modify the cleandepend target in bsd.dep.mk to
also remove any files listed in a new variable named CLEANDEPFILES,
and modify kdump's and truss's Makefiles accordingly.
MFC after: 2 weeks
down some DCMD's without any data. Thanks to Dell and LSI for helping
to provide clues to figure out this problem. Now MegaCli can upgrade
the firmware and should work identical when run on Linux.
Reviewed by: scottl, LSI
MFC after: 1 day
ipsec*_set_policy and do the privilege check only if needed.
Try to assimilate both ip*_ctloutput code blocks calling ipsec*_set_policy.
Reviewed by: rwatson
find | sort. As a bonus, this simplifies the logic considerably. Also
remove the bogus "overruning the args to ls" comment and the corresponding
"-n 20" argument to xargs; the whole point with xargs is precisely that it
knows how large the argument list can safely get.
Note that the first run of the updated script may hypotheticall produce
false positives due to differences between find's and sort's sorting
algorithm. I haven't seen this during testing, but others might.
MFC after: 2 weeks
a variety of bootloaders. This sometimes means that different loader
scripts are required within one ${MACHINE_ARCH}, which makes the
current practice of using ldscript.${MACHINE_ARCH} unsuitable.
Instead, make the default the current convention and allow the ld
scripts to be overridden as necessary.
If we aren't arm, pc98 or sun4v, then enable treating warnings like
errors. That doesn't mean these platforms aren't -Werror clean, just
that we haven't enforced it before. Someone with some spare time
should investigate these three platforms to see if any can be removed.
times when it shouldn't). The PR's patch has been incorporated upstream
as magic.c rev 1.46.
PR: 107676
Submitted by: Dr. Markus Waldeck <waldeck@gmx.de>
rapid wireless association changes in my experience), there is a race
where dhclient is in the process of exiting due to the link going down
when the link coming up causes devd to try and start a new one. This
results is the link being up, but no dhclient running.
Work around this race by checking a second time after a one second delay
before refusing to start a dhclient instance due to one already being
running.
MFC after: 1 week
PCI-express chipset (and thus has functional MSI) if there are any
PCI-express devices in the system, not requiring a root port device.
With PCI-X the chipset detection has to be very conservative because there
are known systems with PCI-X devices that do not appear to have PCI-X
chipsets. However, with PCI-express I'm not sure it is possible to have
a PCI-express device in a system with a non-PCI-express chipset. If we
assume that is the case then this change is valid. It is also required
for at least some PCI-express systems that don't have any devices with
a root port capability (some ICH9 systems).
MFC after: 1 week
Reported by: jfv
- Remove redundant `s' and `S' from yesexpr.
- Add fullwidth latin letters to yesexpr and noexpr (inspired by ja_JP.UTF-8).
- Add korean translated yesexpr (`Ye') and noexpr (`Anio').
- Add yesstr and nostr entries (inspired by zh_CN.*).
- Add UTF-8 encoded file and connect to build.
free function controlable, instead of passing the KVA of the buffer
storage as the first argument.
Fix all conventional users of the API to pass the KVA of the buffer
as the first argument, to make this a no-op commit.
Likely break the only non-convetional user of the API, after informing
the relevant committer.
Update the mbuf(9) manual page, which was already out of sync on
this point.
Bump __FreeBSD_version to 800016 as there is no way to tell how
many arguments a CPP macro needs any other way.
This paves the way for giving sendfile(9) a way to wait for the
passed storage to have been accessed before returning.
This does not affect the memory layout or size of mbufs.
Parental oversight by: sam and rwatson.
No MFC is anticipated.
