(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
operation. Previously ownership was transferred to hardware before
setting address of new RX buffer such that it was possible for
hardware to use wrong RX buffer address.
While here keep compiler from re-ordering instructions by declaring
descriptor members volatile. Memory barriers would do the same job
but volatile is supposed to be cheaper than using memory barriers,
especially on MP systems.
Submitted by: marius
MFC after: 1 week
DP8381[56] and SiS 900/7016 controllers. After r212119, sis(4) no
longer reinitializes controller if ALLMULTI/PROMISC was changed.
However, RX filter handling code assumed some bits of the RX filter
is programmed by driver initialization. This caused ALLMULTI/PROMISC
configuration is ignored under certain conditions.
Fix that issue by reprogramming all bits of RX filter register.
While I'm here follow recommended RX filter programming steps
recommended by National DP8381[56] data sheet(RX filter should be
is disabled before programming).
Reported by: Paul Schenkeveld < freebsd () psconsult dot nl >
Tested by: Paul Schenkeveld < freebsd () psconsult dot nl >
MFC after: 3 days
the original amd64 and i386 headers with stubs.
Rename (AMD64|I386)_BUS_SPACE_* to X86_BUS_SPACE_* everywhere.
Reviewed by: imp (previous version), jhb
Approved by: kib (mentor)
released a drver lock for shared interrupt case such that it caused
panic. While I'm here check whether driver is still running before
serving TX/RX handler.
Reported by: Jerahmy Pocott < QUAKENET1 <> optusnet dot com dot au >
Tested by: Jerahmy Pocott < QUAKENET1 <> optusnet dot com dot au >
MFC after: 3 days
to pad with 0xFF when it encounter short frames. According to RFC
1042 the pad bytes should be 0x00.
Because manual padding consumes extra CPU cycles, introduce a new
tunable which controls the padding behavior. Turning this tunable
on will have driver pad manually but it's disabled by default. Users
can enable software padding by setting the following tunable to
non-zero value.
dev.sis.%d.manual_pad="1"
PR: kern/35422 (patch not used)
prevented driver from working on big-endian machines. Also rewrite
station address programming to make it work on strict-alignment
architectures. With this change, sis(4) now works on sparc64 and
performance number looks good even though sis(4) have to apply
fixup code to align received frames on 2 bytes boundary on sparc64.
allmulti is toggled. Controller does not require reinitialization.
This removes unnecessary controller reinitialization whenever
tcpdump is used.
While I'm here remove unnecessary variable reinitialization.
configured TX/RX MACs before getting a valid link. After that, when
link state change callback is called, it called device
initialization again to reconfigure TX/RX MACs depending on
resolved link state. This hack created several bad side effects and
it required more hacks to not collide with sis_tick callback as
well as disabling switching to currently selected media in device
initialization. Also it seems sis(4) was used to be a template
driver for long time so other drivers which was modeled after
sis(4) also should be changed.
TX/RX MACs are now reconfigured after getting a valid link. Fix for
short cable error is also applied after getting a link because it's
only valid when the resolved speed is 100Mbps.
While I'm here slightly reorganize interrupt handler such that
sis(4) always read SIS_ISR register to see whether the interrupt is
ours or not. This change removes another hack and make it possible
to nuke sis_stopped variable in softc.
o Enforce TX/RX descriptor ring alignment. NS data sheet says the
controller needs 4 bytes alignment but use 16 to cover both SiS
and NS controllers. I don't have SiS data sheet so I'm not sure
what is alignment restriction of SiS controller but 16 would be
enough because it's larger than the size of a TX/RX descriptor.
Previously sis(4) ignored the alignment restriction.
o Enforce RX buffer alignment, 4.
Previously sis(4) ignored RX buffer alignment restriction.
o Limit number of TX DMA segment to be used to 16. It seems
controller has no restriction on number of DMA segments but
using more than 16 looks resource waste.
o Collapse long mbuf chains with m_collapse(9) instead of calling
expensive m_defrag(9).
o TX/RX side bus_dmamap_load_mbuf_sg(9) support and remove
unnecessary callbacks.
o Initial endianness support.
o Prefer local alignment fixup code to m_devget(9).
o Pre-allocate TX/RX mbuf DMA maps instead of creating/destroying
these maps in fast TX/RX path. On non-x86 architectures, this is
very expensive operation and there is no need to do that.
o Add missing bus_dmamap_sync(9) in TX/RX path.
o watchdog is now unarmed only when there are no pending frames
on controller. Previously sis(4) blindly unarmed watchdog
without checking the number of queued frames.
o For efficiency, loaded DMA map is reused for error frames.
o DMA map loading failure is now gracefully handled. Previously
sis(4) ignored any DMA map loading errors.
o Nuke unused macros which are not appropriate for endianness
operation.
o Stop embedding driver maintained structures into descriptor
rings. Because TX/RX descriptor structures are shared between
host and controller, frequent bus_dmamap_sync(9) operations are
required in fast path. Embedding driver structures will increase
the size of DMA map which in turn will slow down performance.
occurs. In addition, the delay when programming the short cable fix
should be 100us, not 100ms.
PR: kern/64556
Submitted by: Thomas Hurst <tom at hur.st>
Approved by: rrs (mentor)
MFC after: 1 week
IF_ADDR_UNLOCK() across network device drivers when accessing the
per-interface multicast address list, if_multiaddrs. This will
allow us to change the locking strategy without affecting our driver
programming interface or binary interface.
For two wireless drivers, remove unnecessary locking, since they
don't actually access the multicast address list.
Approved by: re (kib)
MFC after: 6 weeks
CPU for too long period than necessary. Additively, interfaces are kept
polled (in the tick) even if no more packets are available.
In order to avoid such situations a new generic mechanism can be
implemented in proactive way, keeping track of the time spent on any
packet and fragmenting the time for any tick, stopping the processing
as soon as possible.
In order to implement such mechanism, the polling handler needs to
change, returning the number of packets processed.
While the intended logic is not part of this patch, the polling KPI is
broken by this commit, adding an int return value and the new flag
IFCAP_POLLING_NOCOUNT (which will signal that the return value is
meaningless for the installed handler and checking should be skipped).
Bump __FreeBSD_version in order to signal such situation.
Reviewed by: emaste
Sponsored by: Sandvine Incorporated
When VLAN tagged frame is received the hardware sets 'LONG' bit of
Rx status word. It is always set when the size of received frame
exceeded 1518 bytes, including CRC. This VLAN tagged frame clears
'OK' bit of Rx status word such that driver should not rely on 'OK'
bit of Rx status word to pass the VLAN tagged frame to upper stack.
To fix the bug, don't use SIS_CMDSTS_PKT_OK for Rx error check and
introduce SIS_RXSTAT_ERROR macro that checks Rx errors. If we are
configured to accept VLAN tagged frames and the received frame size
is less than or equal to maximum allowed length of VLAN tagged
frame, clear 'LONG' bit of Rx status word before checking Rx
errors.
Reported by: Vladimir Ermako < samflanker <> gmail DOT com >
Tested by: Vladimir Ermako < samflanker <> gmail DOT com >
night.
Free the children after each pci bus that is searched. Otherwise we
leak them. With free in the new place, we also have to free children
before going to done when we find the device we're looking for.
Also, if we can't get the children of a device, just ignore that bus.
