Commit Graph

31 Commits

Author SHA1 Message Date
Marius Strobl
604f5f1f77 Use DEVMETHOD_END. 2011-11-23 20:27:26 +00:00
Kevin Lo
ee6eac62f7 Remove duplicate header includes 2011-06-28 08:36:48 +00:00
Marius Strobl
3fcb7a5365 - Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
  it might provide useful for debugging). For most mii(4) drivers it
  was unclear whether the PHYs driven by them actually support
  loopback or not. Moreover, typically loopback mode also needs to
  be activated on the MAC, which none of the Ethernet drivers using
  mii(4) implements. Given that loopback media has no real use (and
  obviously hardly had a chance to actually work) besides for driver
  development (which just loopback mode should be sufficient for
  though, i.e one doesn't necessary need support for loopback media)
  support for it is just dropped as both NetBSD and OpenBSD already
  did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
  instead of discrete function pointers, and extend this to include
  a "reset" entry point. Make sure any PHY-specific reset routine is
  always used, and provide one for lxtphy(4) which disables MII
  interrupts (as is done for a few other PHYs we have drivers for).
  This includes changing NIC drivers which previously just called the
  generic mii_phy_reset() to now actually call the PHY-specific reset
  routine, which might be crucial in some cases. While at it, the
  redundant checks in these NIC drivers for mii->mii_instance not being
  zero before calling the reset routines were removed because as soon
  as one PHY driver attaches mii->mii_instance is incremented and we
  hardly can end up in their media change callbacks etc if no PHY driver
  has attached as mii_attach() would have failed in that case and not
  attach a miibus(4) instance.
  Consequently, NIC drivers now no longer should call mii_phy_reset()
  directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
  The purpose of that function is to perform the common steps to attach
  a PHY driver instance and to hook it up to the miibus(4) instance and to
  optionally also handle the probing, addition and initialization of the
  supported media. So all a PHY driver without any special requirements
  has to do in its bus attach method is to call mii_phy_dev_attach()
  along with PHY-specific MIIF_* flags, a pointer to its PHY functions
  and the add_media set to one. All PHY drivers were updated to take
  advantage of mii_phy_dev_attach() as appropriate. Along with these
  changes the capability mask was added to the mii_softc structure so
  PHY drivers taking advantage of mii_phy_dev_attach() but still
  handling media on their own do not need to fiddle with the MII attach
  arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
  for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
  structure. Several PHY drivers require this information also after
  attaching and previously had to wrap their own softc around mii_softc.
  NetBSD/OpenBSD also keep track of the model and revision on their
  mii_softc structure. All PHY drivers were updated to take advantage
  as appropriate.
- Convert the mebers of the MII data structure to unsigned where
  appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
  when mapping an OUI to the MII ID registers. All PHY drivers and
  miidevs where changed as necessary. Actually this now again allows to
  largely share miidevs with NetBSD, which fixed this problem already
  9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
  weren't explicitly converted to support flow control before. It's
  unclear whether flow control actually works with these but typically
  it should and their net behavior should be more correct with these
  changes in place than without if the MAC driver sets MIIF_DOPAUSE.

Obtained from:	NetBSD (partially)
Reviewed by:	yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
Marius Strobl
c6397d3f0e - Even after masking the media with IFM_GMASK the result may have bits
besides the duplex ones set so just comparing it with IFM_FDX may lead
  to false negatives.
- Just let the default case handle all unsupported media types.
- In pnphy_status() don't unnecessarily read a register twice.
- Remove unnused macros.

MFC after:	1 week
2011-01-14 20:26:59 +00:00
Marius Strobl
8e5d93dbb4 Convert the PHY drivers to honor the mii_flags passed down and convert
the NIC drivers as well as the PHY drivers to take advantage of the
mii_attach() introduced in r213878 to get rid of certain hacks. For
the most part these were:
- Artificially limiting miibus_{read,write}reg methods to certain PHY
  addresses; we now let mii_attach() only probe the PHY at the desired
  address(es) instead.
- PHY drivers setting MIIF_* flags based on the NIC driver they hang
  off from, partly even based on grabbing and using the softc of the
  parent; we now pass these flags down from the NIC to the PHY drivers
  via mii_attach(). This got us rid of all such hacks except those of
  brgphy() in combination with bce(4) and bge(4), which is way beyond
  what can be expressed with simple flags.

While at it, I took the opportunity to change the NIC drivers to pass
up the error returned by mii_attach() (previously by mii_phy_probe())
and unify the error message used in this case where and as appropriate
as mii_attach() actually can fail for a number of reasons, not just
because of no PHY(s) being present at the expected address(es).

Reviewed by:	jhb, yongari
2010-10-15 14:52:11 +00:00
Marius Strobl
d7a9ad5688 Consistently always explicitly set IFM_HDX for half-duplex.
Obtained from:	OpenBSD (mostly)
2010-10-03 17:00:57 +00:00
Marius Strobl
de1add1e45 - In the spirit of previous simplifications factor out the checks for a
different PHY instance being selected and isolation out into the wrappers
  around the service methods rather than duplicating them over and over
  again (besides, a PHY driver shouldn't need to care about which instance
  it actually is).
- Centralize the check for the need to isolate a non-zero PHY instance not
  supporting isolation in mii_mediachg() and just ignore it rather than
  panicing, which should sufficient given that a) things are likely to
  just work anyway if one doesn't plug in more than one port at a time and
  b) refusing to attach in this case just leaves us in a unknown but most
  likely also not exactly correct configuration (besides several drivers
  setting MIIF_NOISOLATE didn't care about these anyway, probably due to
  setting this flag for no real reason).
- Minor fixes like removing unnecessary setting of sc->mii_anegticks,
  using sc->mii_anegticks instead of hardcoded values etc.
2010-10-02 18:53:12 +00:00
Marius Strobl
7b9a15f73c Use the mii_data provided via mii_attach_args and mii_pdata respectively
instead of reaching out for the softc of the parent.
2010-09-27 20:31:03 +00:00
Marius Strobl
b54282f61e - Set MIIF_NOLOOP and don't add IFM_LOOP as loopback apparently isn't
supported with these pseudo-PHYs. The MIIF_NOLOOP flag currently triggers
  nothing but hopefully will be respected by mii_phy_setmedia() later on.
- Don't add IFM_NONE as isolation isn't supported by these pseudo-PHYs.
- Use mii_phy_add_media() instead of mii_add_media() so the latter can
  be eventually retired.
2009-03-19 22:34:55 +00:00
Marius Strobl
36bef328f5 cosmetic changes and style fixes 2008-09-30 20:53:15 +00:00
Pyun YongHyeon
07c4a8dfa6 Replace hard-coded magic constants to system defined constants
(BUS_PROBE_DEFAULT, BUS_PROBE_GENERIC etc). These pseudo PHY
drivers were forgotten from the conversion due to the repo copy
to dc driver location.
2006-08-02 05:28:52 +00:00
Warner Losh
6a3033a8b4 Make dc compile after repo-copy. 2005-10-18 06:09:42 +00:00
Warner Losh
7d830ac9c2 Use ansi function definitions in preference to K&R to reduce diffs
with NetBSD (and cause it looks cooler).
2005-09-30 19:39:27 +00:00
Yoshihiro Takahashi
d4fcf3cba5 Remove bus_{mem,p}io.h and related code for a micro-optimization on i386
and amd64.  The optimization is a trivial on recent machines.

Reviewed by:	-arch (imp, marcel, dfr)
2005-05-29 04:42:30 +00:00
Marius Strobl
50aa106108 Remove double __FBSDID and move the remaining one into a common place after
the license(s) and before the driver comment (the latter only in drivers not
having __FBSDID at that location).
2004-05-29 18:09:10 +00:00
David E. O'Brien
aad970f1fe Use __FBSDID().
Also some minor style cleanups.
2003-08-24 17:55:58 +00:00
Poul-Henning Kamp
19ca58475e Remove unnecessary breaks.
Remove unused variables.
Add XXX comment where a break may be missing. [lxtphy.c]

Found by:       FlexeLint
2003-05-31 19:48:33 +00:00
David E. O'Brien
8368cf8f75 Use __FBSDID rather than rcsid[]. 2003-04-03 21:36:33 +00:00
David E. O'Brien
2d3ce7133a Remove miidevs.h and generate it from miidevs at compile time.
The devlist2h.awk tool to do this has been repocopied to sys/tools/.
2003-01-19 02:59:34 +00:00
Alfred Perlstein
9c1c2e9924 Put function return types on a line by themselves.
Cleanup my earlier de-__P sweep and remove whitespace between function
names and paramters.
2002-10-14 22:31:52 +00:00
Poul-Henning Kamp
279fe8d156 Make one generic mii_phy_detach() to replace 19 slightly different ones.
Rename mii_phy_auto_stop() mii_phy_down().

Introduce mii_down(), use it from nge.  Do not indirect it to 19 identical
case's in 19 switchstatements like NetBSD did.
2002-04-29 13:07:38 +00:00
Poul-Henning Kamp
07dd938303 Don't pass three args when one will do just fine, and even prevent
mistakes like the one brgphy.c (now corrected).
2002-04-28 19:25:07 +00:00
Poul-Henning Kamp
83549c664b Improve an API by about 4 lines per driver. 2002-04-28 19:01:32 +00:00
Alfred Perlstein
e51a25f850 Remove __P. 2002-03-20 02:08:01 +00:00
Jonathan Lemon
d9730b8b53 Cleanup pass for mii drivers.
. Make internal service routines static.
   . Use a consistent ordering of checks in MII_TICK.  Do the work in the
     mii_phy_tick() subroutine if appropriate.
   . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
John Baldwin
f34fa851e0 Catch up to header include changes:
- <sys/mutex.h> now requires <sys/systm.h>
- <sys/mutex.h> and <sys/sx.h> now require <sys/lock.h>
2001-03-28 09:17:56 +00:00
John Baldwin
35e0e5b311 Catch up to moving headers:
- machine/ipl.h -> sys/ipl.h
- machine/mutex.h -> sys/mutex.h
2000-10-20 07:58:15 +00:00
Poul-Henning Kamp
db7e3af111 Remove unneeded #include <machine/clock.h> 2000-10-15 14:19:01 +00:00
Bill Paul
d308faacc2 Add #include <machine/mutex.h> since these files need it and don't
include anything else that includes mutex.h. Needed to resolve struct mtx
from struct dc_softc.
2000-10-13 19:15:50 +00:00
Poul-Henning Kamp
3389ae9350 Remove ~25 unneeded #include <sys/conf.h>
Remove ~60 unneeded #include <sys/malloc.h>
2000-04-19 14:58:28 +00:00
Bill Paul
96f2e892a7 Add the if_dc driver and remove all of the al, ax, dm, pn and mx drivers
which it replaces. The new driver supports all of the chips supported
by the ones it replaces, as well as many DEC/Intel 21143 10/100 cards.

This also completes my quest to convert things to miibus and add
Alpha support.
1999-12-04 17:41:31 +00:00