Log:
- merge in latest xenbus from dfr's xenhvm
- fix race condition in xs_read_reply by converting tsleep to mtx_sleep
Log:
unmask evtchn in bind_{virq, ipi}_to_irq
Log:
- remove code for handling case of not being able to sleep
- eliminate tsleep - make sleeps atomic
Note, that the patch provided with this card for the Linux states that
the card uses DEFAULT_RCLK * 2, while in fact it is '* 10'. So probably
we should also use the subdevice/subvendord here. For now just ignore
that fact.
PR: kern/129665
Submitted by: bsam
Obtained from: united efforst with bsam
Now the NDISulator supports NDIS USB drivers that it've tested with
devices as follows:
- Anygate XM-142 (Conexant)
- Netgear WG111v2 (Realtek)
- U-Khan UW-2054u (Marvell)
- Shuttle XPC Accessory PN20 (Realtek)
- ipTIME G054U2 (Ralink)
- UNiCORN WL-54G (ZyDAS)
- ZyXEL G-200v2 (ZyDAS)
All of them succeeded to attach and worked though there are still some
problems that it's expected to be solved.
To use NDIS USB support, you should rebuild and install ndiscvt(8) and
if you encounter a problem to attach please set `hw.ndisusb.halt' to
0 then retry.
I expect no changes of the NDIS code for PCI, PCMCIA devices.
Obtained from: //depot/projects/ndisusb/...
Disable some unneeded pathes in overcomplicated input mixer to help parser
to handle the rest better. This gives mic input boost control in some
configurations and just more predictable operation in others.
Note that you need at least xf86-video-intel 2.4.3 for this to work.
The G4X doesn't put the GATT into the same area of stolen memory
as all the other chips and older versions of the driver didn't
handle that properly.
Tested by: ganbold
Approved by: kib
MFC after: 2 weeks
Note that there is no working backend (or at least
that is mentioned in the PR ticket) but the device
is now supported on our end.
PR: 117205
Submitted by: Artem Naluzhnyy <tut at nhamon dot com dot ua>
MFC after: 1 week
o add EHCI_SCFLG_BIGEMMIO flag to force big-endian byte-select to be
set in USBMODE
o split reset work into new public routine ehci_reset so bus shim drivers
can force big-endian byte-select before ehci_init
event from mii(4) may not be delivered if valid link was already
established. To address the issue, check current link state after
driving MII_TICK. This should fix a regression introduced in
r185753 on fast ethernet controllers.
Reported by: csjp, Bruce Cran < bruce <> cran DOT org DOT uk >
Tested by: csjp, Bruce Cran (initial version)
o add support to byte swap EHCI descriptor contents; the IXP435
has dual-EHCI controllers integral but descriptor contents are
in big-endian format; this support is configured with the
USB_EHCI_BIG_ENDIAN_DESC option and enabled with EHCI_SCFLG_BIGEDESC
o clean up EHCI USBMODE register setup during init; add #defines for
bit values
o split debug support out into a new file and enable use through ddb
o while here remove a bunch of lingering netbsd-isms
Reviewed by: imp
of OFW access semantics, in order to allow future support for real-mode
OF access and flattened device frees. OF client interface modules are
implemented using KOBJ, in a similar way to the PPC PMAP modules.
Because we need Open Firmware to be available before mutexes can be used on
sparc64, changes are also included to allow KOBJ to be used very early in
the boot process by only using the mutex once we know it has been initialized.
Reviewed by: marius, grehan
Intel 855 chips present the same pci id for both heads. This prevents
us from attaching to the dummy second head. All other chips that I
am aware of either only present a single pci id, or different ids
for each head so that we only match on the correct head.
Approved by: kib@
MFC after: 2 weeks
storage class. This check was lost. It is not important for the most cases,
but as it was reported on current@, it does important for sis driver and
surely inportant for AHCI driver. So restore it there.
Submitted by: Toshikazu ICHINOSEKI, Andrey V. Elsukov
Discussed on: current@
ati pci gart to use bus_dma to handle the allocations. This fixes
a garbled screen issue on at least some radeons (X1400 tested). It is
also likely that this is the correct fix for PR# 119324, though that
is not confirmed yet.
Reviewed by: jhb@ (mentor, prior version)
Approved by: kib@
MFC after: 2 weeks
payload length in TSO case. Leaving unused TBD also seem to cause
SCB timeouts under certain conditions when TSO/non-TSO traffics
are active at the same time.
had been the only flag with random usage patterns.
Switch inc_flags to be used as a real bit field by using
INC_ISIPV6 with bitops to check for the 'isipv6' condition.
While here fix a place or two where in case of v4 inc_flags
were not properly initialized before.[1]
Found by: rwatson during review [1]
Discussed with: rwatson
Reviewed by: rwatson
MFC after: 4 weeks
command whenever Tx completion interrupt is raised. The Tx poll
bit is cleared when all packets waiting to be transferred have been
processed. This means the second Tx poll command can be silently
ignored as the Tx poll bit could be still active while processing
of previous Tx poll command is in progress.
To address the issue re(4) used to invoke the Tx poll command in Tx
completion handler whenever it detects there are pending packets in
TxQ. However that still does not seem to completely eliminate
watchdog timeouts seen on RealTek PCIe controllers. To fix the
issue kick Tx poll command only after Tx completion interrupt is
raised as this would indicate Tx is now idle state such that it can
accept new Tx poll command again. While here apply this workaround
for PCIe based controllers as other controllers does not seem to
have this limitation.
Tested by: Victor Balada Diaz < victor <> bsdes DOT net >
out of sleep mode prior to accessing to PHY. This should fix device
attach failure seen on these controllers. Also enable the sleep
mode when device is put into sleep state.
PR: kern/123123, kern/123053
result in panic:
mdconfig -af blah.img -o force
mount /dev/md0 /mnt
mdconfig -du 0
Reviewed by: scottl
Approved by: rwatson (mentor)
Sponsored by: FreeBSD Foundation
configuration registers (which are not going to change) on every interrupt
looks expensive, especially when interrupt is shared. Profiling shows me 3%
of time spent by atapci0 on pure network load due to IRQ sharing with em0.
- Initialize variables before use.
- Remove a KASSERT() that could falsely trigger if there are other sources
of NMIs in the system.
Efficiency tweak:
- When checking PMCs that overflowed, ignore PMCs that were not configured for
sampling.
a real packet error but simply indicate that an unexpected unicast or multicast
error was received by the NIC, which was not counted in the past as well.
Reported by: many (on -stable@)
Reviewed by: davidch
MFC after: 3 days
controllers. Reading this register, for which there are indications
that it doesn't really exist, returns 0 on at least some 12160
and doing so on Sun Fire V880 causes a data access error exception.
Reported and tested by: Beat Gaetzi
Approved by: mjacob
Obtained from: OpenBSD (modulo setting isp_lvdmode)
the code for parsing interrupt maps) to PowerPC and reflect their new MI
status by moving them to the shared dev/ofw directory.
This commit also modifies the OFW PCI enumeration procedure on PowerPC to
allow the bus to find non-firmware-enumerated devices that Apple likes to add,
and adds some useful Open Firmware properties (compat and name) to the pnpinfo
string of children on OFW SBus, EBus, PCI, and MacIO links. Because of the
change to PCI enumeration on PowerPC, X has started working again on PPC
machines with Grackle hostbridges.
Reviewed by: marius
Obtained from: sparc64
1. separating L2 tables (ARP, NDP) from the L3 routing tables
2. removing as much locking dependencies among these layers as
possible to allow for some parallelism in the search operations
3. simplify the logic in the routing code,
The most notable end result is the obsolescent of the route
cloning (RTF_CLONING) concept, which translated into code reduction
in both IPv4 ARP and IPv6 NDP related modules, and size reduction in
struct rtentry{}. The change in design obsoletes the semantics of
RTF_CLONING, RTF_WASCLONE and RTF_LLINFO routing flags. The userland
applications such as "arp" and "ndp" have been modified to reflect
those changes. The output from "netstat -r" shows only the routing
entries.
Quite a few developers have contributed to this project in the
past: Glebius Smirnoff, Luigi Rizzo, Alessandro Cerri, and
Andre Oppermann. And most recently:
- Kip Macy revised the locking code completely, thus completing
the last piece of the puzzle, Kip has also been conducting
active functional testing
- Sam Leffler has helped me improving/refactoring the code, and
provided valuable reviews
- Julian Elischer setup the perforce tree for me and has helped
me maintaining that branch before the svn conversion
time it is marked for user space callchain capture in the NMI
handler and the time the callchain capture callback runs.
- Improve code and control flow clarity by invoking hwpmc(4)'s user
space callchain capture callback directly from low-level code.
Reviewed by: jhb (kern/subr_trap.c)
Testing (various patch revisions): gnn,
Fabien Thomas <fabien dot thomas at netasq dot com>,
Artem Belevich <artemb at gmail dot com>
if (batt_sleep_ms)
AcpiOsSleep(1);
where the rest are all:
if (batt_sleep_ms)
AcpiOsSleep(batt_sleep_ms);
I can't recall why that one was different, so change it
to match the rest.
Pointed out by: Christoph Mallon
MFC after: 2 weeks
On some laptops with smart batteries, enabling battery monitoring
software causes keystrokes from atkbd to be lost. This has also been
reported on Linux, and is apparently due to the keyboard and I2C line
for the battery being routed through the same chip. Whether that's
accurate or not, adding extra sleeps to the status checking code
causes the problem to go away.
I've been running this for nearly six months now on my laptop,
it works like a charm.
Reviewed by: Nate Lawson (in a previous revision)
MFC after: 2 weeks
o recognize ixp435 cpu
o change memory layout for for ixp4xx to not assume memory is aliases
to 0x10000000 (Cambria/ixp435 memory starts at zero)
o handle 64 irqs for ixp435
o dual EHCI USB 2.0 controller integral to ixp435
o overhaul NPE code for ixp435 and better MAC+MII naming
o updated NPE firmware (including NPE-A image for ixp435/ixp465)
o Gateworks Cambria board support:
- IDE compact flash
- MCU
- front panel LED on i2c bus
- Octal LED latch
Sanity-tested with NFS-root on Avila and Cambria boards. Requires
pending boot2 mods for CF-boot on Cambria.
o Try to be smarter about reading the ExCA CSC register. Now, we only
do it for 16-bit cards. Add some experimental code to treat it like
a power interrupt, but I'm not 100% sure that I like it. It may be
removed upon further testing. It seemed to help in one test case, but
the evidence may be inconclusive. This may be beneficial for cleaning up
exca_reset and exca_wait_ready.
o Check for CSTS events on the socket event register. We ask for it when
we're powering up a card, but I don't think we're otherwise using
it. Just ACK the interrupt for now. In theory, we can use it
instead of the busy wait we do in cbb_cardbus_reset. More research
is necessary to see if we can optimize things there when we're
waiting for the DEVVENDOR register to become valid.
o Rework the comments a bit. Minor tidying up. Etc.
causes data corruption in combination with certain bridges.
Information about this problem was kindly provided by davidch. [1]
- As BGE_FLAG_PCIX is meant to indicate that the controller is in
PCI-X mode, revert to the pre __FreeBSD_version 602101 method of
reading the bus mode register rather than checking the mere
existence of a PCI-X capability, which is also there when the
NIC f.e. is put into a 32-bit slot causing it not to be in PCI-X
mode. Setting BGE_FLAG_PCIX inappropriately could cause the NIC
to be tuned incorrectly.
PR: 128833 [1]
Reviewed by: jhb
MFC after: 3 days
When VLAN tagged frame is received the hardware sets 'LONG' bit of
Rx status word. It is always set when the size of received frame
exceeded 1518 bytes, including CRC. This VLAN tagged frame clears
'OK' bit of Rx status word such that driver should not rely on 'OK'
bit of Rx status word to pass the VLAN tagged frame to upper stack.
To fix the bug, don't use SIS_CMDSTS_PKT_OK for Rx error check and
introduce SIS_RXSTAT_ERROR macro that checks Rx errors. If we are
configured to accept VLAN tagged frames and the received frame size
is less than or equal to maximum allowed length of VLAN tagged
frame, clear 'LONG' bit of Rx status word before checking Rx
errors.
Reported by: Vladimir Ermako < samflanker <> gmail DOT com >
Tested by: Vladimir Ermako < samflanker <> gmail DOT com >
Waiting for 1ms for each GMII register access looks overkill and it
may also decrease overall performance of driver because re(4)
invokes mii_tick for every hz.
Tested by: rpaulo
established a valid link or not. In miibus_statchg handler add a
check for established link is valid one for the controller(e.g.
1000baseT is not a valid link for fastethernet controllers.)
o Added a flag RE_FLAG_FASTETHER to mark fastethernet controllers.
o Added additional check to know whether we've really encountered
watchdog timeouts or missed Tx completion interrupts. This change
may help to track down the cause of watchdog timeouts.
o In interrupt handler, removed a check for link state change
interrupt. Not all controllers have the bit and re(4) did not
rely on the event for a long time. In addition, re(4) didn't
request the interrupt in RL_IMR register.
Tested by: rpaulo
drivers, there should be a 1us delay after every write when
bit-banging the MII. Also insert barriers in order to ensure
the intended ordering. These changes hopefully will solve the
bus wedging occasionally experienced with DM9102A since r182461.
- Deobfuscate dc_mii_readreg() a bit.
multiple algorithms and potentially collect multiple samples.
Instead of a single calibration interval we now have short and long
intervals; the long interval roughly corresponds to the previous
single interval. The short interval is used to speedup collection
of samples and happens much quicker. We make calls using the short
interval until we're told the calibration work is complete at which
point we fallback to the long interval. In addition there is a
much longer reset interval used to flush all calibration state and
cause everthing to start anew.
With these changes you can also disable calibration entirely by
setting the long interval to zero.
at. I don't think this will make a huge difference, but I have
received a report of a interrupt storm on one 16-bit card that this
might fix (chances are it won't, since I think that we may need to
check both the CBB registers for the 16-bit card as well as the PCIC
registers for power state change).
Submitted by: jhb@
the power interrupt and init code waiting for the interrupt are
running on different CPUs. I haven't seen this make any real
difference, but I've also had some reports of odd behavior I can't
otherwise explain. It is an infrequent operation, and certainly
wouldn't hurt.
my right mouse button and keyboard LEDs from working due to mangled
configuration packets. Fixed several other races and associated problems in the
main ADB stack that were exposed while fixing this.
Now it is possible to suspend/resume with inserted and active card.
To reinitialize card on resume and to detect card change while suspended,
implement bus rescan routines. It can also be used by controllers without
card presence detection signals or with multiple cards per slot support.
While there, cleanup msleep() usage. We have no any rights to exit without
"request done" signal from driver as it could lead to modify after free.
interrupt code to be more robust. I've been running these changes for
over a year... With these changes, I don't see the ath card going
into reset like the code in the tree.
packet loss, of between 10-30%. The fix is to put the PHY into
and take it out of local loopback mode when resetting the interface.
Obtained from: Chelsio Inc.
MFC after: 3 days
o Chip full mask revision 2 or later controllers have to
set correct Tx MAC and Tx offload clock depending on negotiated
link speed.
o JMC260 chip full mask revision 2 has a silicon bug that can't
handle 64bit DMA addressing. Add workaround to the bug by
limiting DMA address space to be within 32bit.
o Valid FIFO space of receive control and status register was
changed on chip full mask revision 2 or later controllers. For
these controllers, use default 16QW as it's supposed to be the
safest value for maximum PCIe compatibility. JMicron confirmed
performance will not be reduced even if the FIFO space is set
to 16QW.
o When interface is put into suspend/shutdown state, remove Tx MAC
and Tx offload clock to save more power. We don't need Tx clock
at all in this state.
o Added new register definition for chip full mask revision 2 or
later controllers.
Thanks to JMicron for their continuous support of FreeBSD.
change. As a side effect, this makes the excessive interrupts to
disappear which has been observed as a regression in recent stable/7.
Reported by: many (on -stable@)
Reviewed by: davidch
directly include only the header files needed. This reduces the
unneeded spamming of various headers into lots of files.
For now, this leaves us with very few modules including vnet.h
and thus needing to depend on opt_route.h.
Reviewed by: brooks, gnn, des, zec, imp
Sponsored by: The FreeBSD Foundation
when it sees only received packets. In some cases where a device only
recieves data it mistakenly thinks that its transmitting side is broken
and resets the device.
Obtained from: Chelsio Inc.
MFC after: 3 days
hardware for PMCs that have been configured for sampling.
- Bug fix: acknowledge PMC hardware overflows irrespective of the
the (software) PMC's state.
- break complex conditionals in to multiple lines to avoid wrapping
- remove copious unused debug statements
- be more aggressive about cleaning in the calling thread
- eliminate usage of ENOSPC
- increase number of iterations that cxgbsp can do
- eliminate "initerr" usage to simplify ENOBUFS handling
- when coalescing pass all packets to BPF
- always set overrun if hardware queue is full
offload for VLAN frames are also supported. The VLAN hardware
assistance is available only on 82550/82551 based controllers.
While I'm here change the confusing name of bit1 in byte 22 of
configuration block to vlan_drop_en. The bit controls whether
hardware strips VLAN tagged frame or not. Special thanks to wpaul
who sent valuable VLAN related information to me.
Tested on: i386, sparc64
events. Just reading PMDR register was not enough to have fxp(4)
immuninize against received magic packets during system boot.
Tested by: Alexey Shuvaev < shuvaev <> physik DOT uni-wuerzburg DOT de >
module; the ath module now brings in the hal support. Kernel
config files are almost backwards compatible; supplying
device ath_hal
gives you the same chip support that the binary hal did but you
must also include
options AH_SUPPORT_AR5416
to enable the extended format descriptors used by 11n parts.
It is now possible to control the chip support included in a
build by specifying exactly which chips are to be supported
in the config file; consult ath_hal(4) for information.
o eliminate private state indexed by 802.11 rate codes; use the hal's
rate tables directly to get the same info
o calculate a mask of operational rates to optimize lookups and checks
(instead of using for loops and similar)
o optimize size bin operations
o ignore rates marked as "do not use" in the hal phy tables
o fix bug that caused upshifting to break in 11g once the rate dropped
below 11Mb/s
o add more intelligent multi-rate tx schedules
o add support for 1/2 and 1/4 width channels
o add dev.ath.X.sample_stats sysctl to dump runtime statistics to the console
(needs to go up to a user app)
o export more tuning knobs via sysctls (still a couple of magic constants)
necessary workarounds, add code to detect these hangs and distinguish
them from other events; note this code is only invoked for anomalous
conditions and (at the moment) is a noop because the hang detection
code is in a new hal that's coming shortly
and Core Duo), models 0xF (Core2), model 0x17 (Core2Extreme) and
model 0x1C (Atom).
In these CPUs, the actual numbers, kinds and widths of PMCs present
need to queried at run time. Support for specific "architectural"
events also needs to be queried at run time.
Model 0xE CPUs support programmable PMCs, subsequent CPUs
additionally support "fixed-function" counters.
- Use event names that are close to vendor documentation, taking in
account that:
- events with identical semantics on two or more CPUs in this family
can have differing names in vendor documentation,
- identical vendor event names may map to differing events across
CPUs,
- each type of CPU supports a different subset of measurable
events.
Fixed-function and programmable counters both use the same vendor
names for events. The use of a class name prefix ("iaf-" or
"iap-" respectively) permits these to be distinguished.
- In libpmc, refactor pmc_name_of_event() into a public interface
and an internal helper function, for use by log handling code.
- Minor code tweaks: staticize a global, freshen a few comments.
Tested by: gnn
controllers. ICH based controllers are treated as 82559. 82557,
earlier revision of 82558 and 82559ER have no WOL capability.
o WOL support requires help of a firmware so add check whether
hardware is capable of handling magic frames by reading EEPROM.
o Enable accepting WOL frames only when hardware is about to
suspend or shutdown. Previously fxp(4) used to allow receipt of
magic frame under normal operation mode which could cause
hardware hang if magic frame is received by hardware. Datasheet
clearly states driver should not allow WOL frames under normal
operation mode.
o Disable WOL frame reception in device attach so have fxp(4)
immunize against system hang which can be triggered by magic
packets when the hardware is not in fully initialized state.
o Don't reset all hardware configuration data in fxp_stop()
otherwise important configuration data is lost and this would
reset WOL configuration to default state which in turn cause
hardware hang on receipt of magic frames. To fix the issue,
preserve hardware configuration data by issuing a selective
reset.
o Explicitly disable interrupts after issuing selective reset as
reset may unmask interrupts.
Tested by: Alexey Shuvaev < shuvaev <> physik DOT uni-wuerzburg DOT de >
will sometimes fail to initialize problem due to a lock
contention with management hardware. However, in order to
deliver that fix it was necessary to take a shared code
update as a whole, and this required scattered changes in
the core code to be compatible.
The em driver now has VLAN HW support added as the igb
driver had previously.
MFC after: ASAP - in time for 7.1 RELEASE
-This version has header split, and as a result a number of
aspects of the code have been improved/simplified.
- Interrupt handling refined for performance
- Many small bugs fixed along the way
MFC after: ASAP - in time for 7.1
- Bugfix: Don't excede static number of ports allowed when iterating
over endpoints within an interface.
- u3g_speeds contains speeds in baud, not bytes per second, so divide
the buffer size by 10.
o Configure controller to use dynamic TBD as TSO requires that
operation mode.
o Add a dummy TBD to tx_cb_u as TSO can access one more TBD in TSO
operation.
o Increase a DMA segment size to 4096 to hold a full IP segment
with link layer header.
o Unlike other TSO capable controllers, 82550/82551 does not
modify the first IP packet in TSO operation so driver should
create an IP packet with proper header. Subsequent IP packets
are generated from the header information in the first IP packet
header. Likewise pseudo checksum also should be computed by
driver for the first packet.
o TSO requires one more TBD to hold total TCP payload. To make
code simple for TSO/non-TSO case, increase the index of the
first available TBD array.
o Remove KASSERT that checks the size of a DMA segment should be
less than or equal to MCLBYTES as it's no longer valid in TSO.
o Tx threshold and number of TBDs field is used to store MSS in
TSO. So don't set the Tx threshold in TSO case.
82559 or later controllers added simple checksum calculation logic
in RU. For backward compatibility the computed checksum is appended
at the end of the data posted to Rx buffer. This type of simple
checksum calculation support had been used on several vendors such
as Sun HME/GEM, SysKonnect GENESIS and Marvell Yukon controllers.
Because this type of checksum offload support requires parsing of
received frame and pseudo checksum calculation with software
routine it still consumes more CPU cycles than that of full-fledged
checksum offload controller. But it's still better than software
checksum calculation.
Rx buffer and loads DMA map. Also add a function
fxp_discard_rfabuf that handles reusing Rx buffer/DMA map. With
this change fxp_add_rfabuf just handles appending a new RFA to
existing chain.
o Initialize mbuf length in fxp_new_rfabuf.
o Don't reset rnr and have fxp(4) handle received frames even if
it couldn't allocate new Rx buffer. This will make fxp(4) reload
updated RFA under rnr case. The rnr would still be reset to 0 if
polling is active and fxp(4) processed number of allowed Rx
events.
o Update if_iqdrops if fxp(4) couldn't allocate Rx buffer.
Previously fxp(4) used to try to reuse Rx buffer when new buffer
allocation is failed. But fxp(4) didn't take into account loaded
DMA map such that the same DMA map was loaded again without
unloading the map. There is no reason to unload the loaded map and
reload the same map again, just reusing the map is enough. I
believe the spare DMA map in softc was introduced to implement this
behaviour. Also fxp(4) used to stop Rx processing if once Rx buffer
allocation or DMA map load fails which in turn resulted in losing
incoming frames under heavy network load. With this change fxp(4)
should survive from resource shortage condition.
Fix some issues about re-scanning of the devices.
src/lib/libusb20/libusb20_ugen20.c
Fix issue about libusb20 having to release the
USB transfers before doing a SET_CONFIG, else
the kernel will kill the file handle.
src/sys/dev/usb2/core/usb2_device.
src/sys/dev/usb2/core/usb2_generic.c
src/sys/dev/usb2/core/usb2_generic.h
Add support for U3G devices.
Improve and cleanup FIFO free handling.
Improve device re-enumeration.
src/sys/dev/usb2/core/usb2_msctest.c
src/sys/dev/usb2/core/usb2_msctest.h
Fix some problems in the USB Mass Storage Test.
Add Huawei vendor specific quirks.
src/sys/dev/usb2/core/usb2_request.c
Improve device re-enumeration.
src/sys/dev/usb2/ethernet/if_aue2.c
src/sys/dev/usb2/include/usb2_devid.h
src/sys/dev/usb2/include/usb2_devtable.h
src/sys/dev/usb2/quirk/usb2_quirk.c
Integrate changes from the old USB driver.
src/sys/dev/usb2/include/usb2_standard.h
Add definition of USB3.0 structures from USB.org.
src/sys/dev/usb2/serial/u3g2.c
src/sys/dev/usb2/serial/ugensa2.c
src/sys/modules/usb2/Makefile
src/sys/modules/usb2/serial_3g/Makefile
Import U3G driver.
Submitted by: Hans Petter Selasky (usb4bsd)
many bugs fixes, many more performance improvements.
Submitted by: Danny Braniss
M sbin/iscontrol/iscsi.conf.5
M sbin/iscontrol/iscontrol.8
M sbin/iscontrol/iscontrol.h
M sbin/iscontrol/config.c
M sbin/iscontrol/fsm.c
M sbin/iscontrol/login.c
M sbin/iscontrol/pdu.c
M sbin/iscontrol/misc.c
M sbin/iscontrol/auth_subr.c
M sbin/iscontrol/iscontrol.c
M sys/dev/iscsi/initiator/isc_cam.c
M sys/dev/iscsi/initiator/iscsi.h
M sys/dev/iscsi/initiator/isc_soc.c
M sys/dev/iscsi/initiator/iscsi_subr.c
M sys/dev/iscsi/initiator/iscsivar.h
M sys/dev/iscsi/initiator/isc_subr.c
M sys/dev/iscsi/initiator/iscsi.c
M sys/dev/iscsi/initiator/isc_sm.c
IFF_DRV_OACTIVE to note resource shortage to upper stack.
- Don't count number of mbuf chains. Default 32 DMA segments for a
frame is enough for most cases. If bus_dmamap_mbuf_sg fails use
m_collapse(9) to collapse the mbuf chain instead of relying on
expensive m_defrag(9).
- Move bpf handling to fxp_start_body() which is supposed to be
more appropriate place.
- Always arm watchdog timer whenever a new Tx request is made.
Previously fxp(4) used to arm watchdog timer only when
FXP_CXINT_THRESH-th Tx request is made. Because fxp(4) does not
rely on Tx interrupt to reclaim transmitted mbufs it's better to
arm watchdog timer to detect potential lockups.
- Add more aggresive Tx buffer reclaiming in fxp_start_body to make
room for new Tx requests. Since fxp(4) does not request Tx
completion interrupt for every frames it's necessary to clean
TXCBs in advance to saturate link.
- Make fxp(4) try to start more packets transmitting regardless of
interrupt type in fxp_intr_body.
patch the RX/TX performance becomes about 17~18 Mbps comparing with
the previous whose values were RX 7~8Mbps and TX 13~14Mbps.
- improve AL2230 RF handling in zd1211b
- support AL2230S RF that PV2000 is renamed to AL2230S
- use register ZYD_CR244, ZYD_CR243, ZYD_CR242 when the driver writes
values on RF. This routine is more faster than the original one
- use private TX lock to avoid LOR at zyd_raw_xmit()
- increase TX slots from 1 to 5
- needs to set the channel at IEEE80211_S_AUTH not IEEE80211_S_RUN
- detailed error handling. In previous the next command was sent to the
device even if there was errors
- setting ZYD_MAC_RX_THRESHOLD value should be different between 1211
and 1211b
- only try to stop the device at zyd_init_locked() if the device is
UPed
- do not use MTX_RECURSE
- do not try to grap Giant lock when the channel is changing
- move the device initialization routines from zyd_attach to zyd_init to
give a device full-reset chance to the driver.
- code cleanup at zyd_raw_xmit()
- simplify zyd_attach() routines
- resort functions and clean up variables
- DPRINTF style change.
- style(9)
Reviewed by: sam
check to fxp_txeof(). While I'm here unarm watchdog timer only if
there are no pending queued Tx requests.
Previously the watchdog timer was unarmed whenever Tx interrupt is
raised. This could be resulted in hiding root cause of watchdog
timeouts.
checksum offload configuration. Now checksum offload can be
controlled by ifconfig(8).
While I'm here add an additional check for interface capabilities
before applying user's request.
nodes capabilities. Add "Analog"/"Digital" marks to the pcm device names.
I hope it will help new users easier accept concept of several PCM devices
and understand exact purposes of that devices.
- invert sense of hw.cxgb.singleq tunable to hw.cxgb.multiq
- don't wake up transmitting thread by default
- add per tx queue ifaltq to handle ALTQ
- remove several unused functions in cxgb_multiq.c
- add several sysctls: multiq_tx_enable, coalesce_tx_enable,
and wakeup_tx_thread
- this obsoletes the hw.cxgb.snd_queue_len as ifq is replaced
by a buf_ring
and ifnet functions
- add memory barriers to <machine/atomic.h>
- update drivers to only conditionally define their own
- add lockless producer / consumer ring buffer
- remove ring buffer implementation from cxgb and update its callers
- add if_transmit(struct ifnet *ifp, struct mbuf *m) to ifnet to
allow drivers to efficiently manage multiple hardware queues
(i.e. not serialize all packets through one ifq)
- expose if_qflush to allow drivers to flush any driver managed queues
This work was supported by Bitgravity Inc. and Chelsio Inc.
1) Fix a bug in dealing with the Alerus 1006 PHY which prevented the
device from ever coming back up once it had been set to down.
2) Add a kernel tunable (hw.cxgb.snd_queue_len) which makes it possible
to give the device more than IFQ_MAXLEN entries in its send queue. The
default remains 50.
3) Add code to place the card'd identification and serial number into
its description (%desc) so that users can tell which card they have
installed.
and output, set BUS_DMA_COHERENT when creating the DMA map used for
loading the buffer. As a side-effect this solves locking issues on
sparc64 when dcons(4) calls bus_dmamap_sync(9) while in an interrupt
filter, which are executed in a critical section, and iommu(4) has
to use a sleep lock when taking advantage of the streaming buffer.
Reported and tested by: kensmith
Approved by: simokawa
For some reason the nmdm(4) driver doesn't use CALLOUT_MPSAFE, even
though we live in the MPSAFE TTY era. Add the CALLOUT_MPSAFE flags.
System survives.
for virtualization.
Instead of initializing the affected global variables at instatiation,
assign initial values to them in initializer functions. As a rule,
initialization at instatiation for such variables should never be
introduced again from now on. Furthermore, enclose all instantiations
of such global variables in #ifdef VIMAGE_GLOBALS blocks.
Essentialy, this change should have zero functional impact. In the next
phase of merging network stack virtualization infrastructure from
p4/vimage branch, the new initialization methology will allow us to
switch between using global variables and their counterparts residing in
virtualization containers with minimum code churn, and in the long run
allow us to intialize multiple instances of such container structures.
Discussed at: devsummit Strassburg
Reviewed by: bz, julian
Approved by: julian (mentor)
Obtained from: //depot/projects/vimage-commit2/...
X-MFC after: never
Sponsored by: NLnet Foundation, The FreeBSD Foundation
src/sys/dev/usb2/core/usbdevs
src/sys/dev/usb2/include/urio2_ioctl.h
src/sys/dev/usb2/storage/ustorage2_fs.h
These files are not used any more.
src/usr.sbin/Makefile
src/etc/mtree/BSD.include.dist
src/include/Makefile
src/lib/Makefile
src/share/man/man7/hier.7
src/share/mk/bsd.libnames.mk
src/etc/mtree/BSD.include.dist
Make "usbconfig" and "libusb20" a part of the default build.
src/sys/dev/usb/rio500_usb.h
src/sys/dev/usb2/storage/urio2.c
Use common include file.
src/sys/dev/usb2/bluetooth/ng_ubt2.c
Make USB bluetooth depend on "ng_hci" module.
src/sys/dev/usb2/controller/ehci2.c
src/sys/dev/usb2/controller/ehci2.h
Patches for Marvell EHCI.
src/sys/dev/usb2/core/usb2_busdma.c
Bugfix for 64-bit platforms. Need to unload the previously loaded DMA
map and some cleanup regarding some corner cases.
src/sys/dev/usb2/core/usb2_core.h
src/sys/dev/usb2/core/usb2_dev.c
src/sys/dev/usb2/core/usb2_dev.h
Bugfix for libusb filesystem interface.
New feature: Add support for filtering device data at the expense of the
userland process.
Add some more comments.
Some minor code styling.
Remove unused function, usb2_fifo_get_data_next().
Fix an issue about "fifo_index" being used instead of "ep_index".
src/sys/dev/usb2/core/usb2_device.c
src/sys/dev/usb2/core/usb2_generic.c
Bugfix for Linux USB compat layer. Do not free non-generic FIFOs when
doing an alternate setting.
Cleanup USB IOCTL and USB reference handling.
Fix a corner case where USB-FS was left initialised after
setting a new configuration or alternate setting.
src/sys/dev/usb2/core/usb2_hub.c
Improvement: Check all USB HUB ports by default at least one time.
src/sys/dev/usb2/core/usb2_request.c
Bugfix: Make sure destination ASCII string is properly zero terminated
in all cases.
Improvement: Skip invalid characters instead of replacing with a dot.
src/sys/dev/usb2/core/usb2_util.c
src/sys/dev/usb2/image/uscanner2.c
Spelling.
src/sys/dev/usb2/include/Makefile
Share "usbdevs" with the old USB stack.
src/sys/dev/usb2/include/usb2_devid.h
src/sys/dev/usb2/include/usb2_devtable.h
Regenerate files.
Alfred: Please fix the RCS tag at the top.
src/sys/dev/usb2/include/usb2_ioctl.h
Fix compilation of "kdump".
src/sys/dev/usb2/serial/ubsa2.c
src/sys/dev/usb2/serial/ugensa2.c
Remove device ID's which will end up in a new 3G driver.
src/sys/dev/usb2/sound/uaudio2.c
Correct a debug printout.
src/sys/dev/usb2/storage/umass2.c
Sync with old USB stack.
src/lib/libusb20/libusb20.3
Add more documentation.
src/lib/libusb20/libusb20.c
Various bugfixes and improvements.
src/usr.sbin/usbconfig/dump.c
src/usr.sbin/usbconfig/usbconfig.c
New commands for dumping strings and doing custom USB requests from
the command line.
Remove keyword requirements from generated files:
"head/sys/dev/usb2/include/usb2_devid.h"
"head/sys/dev/usb2/include/usb2_devtable.h"
- An "at" hint now reserves a device name.
- A new BUS_HINT_DEVICE_UNIT method is added to the bus interface. When
determining the unit number of a device, this method is invoked to
let the bus driver specify the unit of a device given a specific
devclass. This is the only way a device can be given a name reserved
via an "at" hint.
- Implement BUS_HINT_DEVICE_UNIT() for the acpi(4) and isa(4) bus drivers.
Both of these busses implement this by comparing the resources for a
given hint device with the resources enumerated by ACPI/PnPBIOS and
wire a unit if the hint resources are a subset of the "real" resources.
- Use bus_hinted_children() for adding hinted devices on isa(4) busses
now instead of doing it by hand.
- Remove the unit kludging from sio(4) as it is no longer necessary.
Prodding from: peter, imp
OK'd by: marcel
MFC after: 1 month
read before we configure the card, so we can implement
/dev/cardbus*.cis. Also, do this on a per-child basis, so we now have
a different name than before. I think i'll have to fix that for some
legacy tools to keep working.
I can now do a dumpcis on my running atheros card and have it still work!
redundant malloc/free. Add comments about how this should really be
done. Fix an overly verbose comment about under 1MB mapping: go ahead
and set the bits, but we ignore them.
- If the flag is set and auto-select fails, assume disk is not present.
- Set disk empty flag only when the floppy controller reset is needed.
It fixes regression introduced in r1.311, which prevented it from ignoring
errors. Now fdformat(1) and dd(1) with conv=noerror option can continue
when read/write errors occur as they should.
- Do not retry disk probing as it is extremely slow and pointless.
- Move the disk probing code into a separate function.
- Do not reset disk empty flag if write-protect check fails somehow.
PR: kern/116538[1]
the softc is reset a few times during probing.
Print 'changing to modem mode' messages if booting verbose to show the
reason for the time delay. Note: Some devices (Huawei for one) take 20
seconds to appear on the USB bus).
can be controlled by ifconfig(8). Note, VLAN hardware tagging
controls still lacks required handler but it requires more driver
cleanups so I didn't touch that part.
PR: kern/128766
- Fix to ioctl path in which the length could be 0 which means
no data in/out from LSI.
- Fix to ioctl path in which the data in the sense data space
of the ioctl packet is a really a pointer to some location in
user-space. From LSI re-worked a bit by me.
- Add HW support for next gen cards from LSI.
Thanks to LSI for their support!
Submitted by: jhb, LSI
MFC after: 3 days
The same (vendor, product) tuple is used for aue(4) adapters,
but I am not sure if the quirk is correct. I'm using the USB
device 'release' info to skip aue(4) detection right now, but
if there's a better way to differentiate between USB-LAN and
USB Bluetooth we should update the quirk.
Reviewed by: imp, rink
MFC after: 2 weeks
controller. The controller is also known as L1E(AR8121) and
L2E(AR8113/AR8114). Unlike its predecessor Attansic L1,
AR8121/AR8113/AR8114 uses completely different Rx logic such that
it requires separate driver. Datasheet for AR81xx is not available
to open source driver writers but it shares large part of Tx and
PHY logic of L1. I still don't understand some part of register
meaning and some MAC statistics counters but the driver seems to
have no critical issues for performance and stability.
The AR81xx requires copy operation to pass received frames to upper
stack such that ale(4) consumes a lot of CPU cycles than that of
other controller. A couple of silicon bugs also adds more CPU
cycles to address the known hardware bug. However, if you have fast
CPU you can still saturate the link.
Currently ale(4) supports the following hardware features.
- MSI.
- TCP Segmentation offload.
- Hardware VLAN tag insertion/stripping with checksum offload.
- Tx TCP/UDP checksum offload and Rx IP/TCP/UDP checksum offload.
- Tx/Rx interrupt moderation.
- Hardware statistics counters.
- Jumbo frame.
- WOL.
AR81xx PCIe ethernet controllers are mainly found on ASUS EeePC or
P5Q series of ASUS motherboards. Special thanks to Jeremy Chadwick
who sent the hardware to me. Without his donation writing a driver
for AR81xx would never have been possible. Big thanks to all people
who reported feedback or tested patches.
HW donated by: koitsu
Tested by: bsam, Joao Barros <joao.barros <> gmail DOT com >
Jan Henrik Sylvester <me <> janh DOT de >
Ivan Brawley < ivan <> brawley DOT id DOT au >,
CURRENT ML
- Do not let individual KLD module unregister firmware image loaded by ispfw
or vice versa.
- Make 'kldunload ispfw' actually unregister all firmware images loaded by
ispfw, not just 'isp_1040'.
- Print which KLD module actually loaded the firmware image.
- Remove unused return value from do_load_fw() and do_unload_fw() and remove
duplicate sys/param.h while I am here.
dependencies. A 'struct pmc_classdep' structure describes operations
on PMCs; 'struct pmc_mdep' contains one or more 'struct pmc_classdep'
structures depending on the CPU in question.
Inside PMC class dependent code, row indices are relative to the
PMCs supported by the PMC class; MI code in "hwpmc_mod.c" translates
global row indices before invoking class dependent operations.
- Augment the OP_GETCPUINFO request with the number of PMCs present
in a PMC class.
- Move code common to Intel CPUs to file "hwpmc_intel.c".
- Move TSC handling to file "hwpmc_tsc.c".
On RELENG_6 (and probably RELENG_7) we see our syscons windows and
pseudo-terminals have the following buffer sizes:
| LINE RAW CAN OUT IHIWT ILOWT OHWT LWT COL STATE SESS PGID DISC
| ttyv0 0 0 0 7680 6720 2052 256 7 OCcl 1146 1146 term
| ttyp0 0 0 0 7680 6720 1296 256 0 OCc 82033 82033 term
These buffer sizes make no sense, because we often have much more output
than input, but I guess having higher input buffer sizes improves
guarantees of the system.
On MPSAFE TTY I just sent both the input and output buffer sizes to 7
KB, which is pretty big on a standard FreeBSD install with 8 syscons
windows and some PTY's. Reduce the baud rate to 9600 baud, which means
we now have the following buffer sizes:
| LINE INQ CAN LIN LOW OUTQ USE LOW COL SESS PGID STATE
| ttyv0 1920 0 0 192 1984 0 199 7 2401 2401 Oil
| pts/0 1920 0 0 192 1984 0 199 5631 1305 2526 Oi
This is a lot smaller, but for pseudo-devices this should be good
enough. You need to do a lot of punching to fill up a 7.5 KB input
buffer. If it turns out things don't work out this way, we'll just
switch to 19200 baud.
NATM needs 'struct in_addr' to compile, which is a problem on its own
but include in.h for now if we have NATM but neither INET or INET6.
MFC after: 2 months
the sc does not have 'an_have_rssimap' variable.
Add an ANCACHE check to poperly hide the case and make an(4)
compile without INET.
MFC after: 2 months
Because the TTY hooks interface was not finished when I imported the
MPSAFE TTY layer, I had to disconnect the snp(4) driver. This snp(4)
implementation has been sitting in my P4 branch for some time now.
Unfortunately it still doesn't use the same error handling as snp(4)
(returning codes through FIONREAD), but it should already be usable.
I'm committing this to SVN, hoping someone else could polish off its
rough edges. It's always better than having a broken driver sitting in
the tree.
Note that these changes will not make the driver work on powerpc, but it should fix at least the i386/amd64 cases.
Obtained from: //depot/projects/usb/src/sys/dev/usb2/wlan/if_zyd2.c#20
Noticed by: jeli, ed
vnode in question does not need to be held. All the data structures used
during the name lookup are protected by the global name cache lock.
Instead, the caller merely needs to ensure a reference is held on the
vnode (such as vhold()) to keep it from being freed.
In the case of procfs' <pid>/file entry, grab the process lock while we
gain a new reference (via vhold()) on p_textvp to fully close races with
execve(2).
For the kern.proc.vmmap sysctl handler, use a shared vnode lock around
the call to VOP_GETATTR() rather than an exclusive lock.
MFC after: 1 month
that includes significant features and SMP safety.
This commit includes a more or less complete rewrite of the *BSD USB
stack, including Host Controller and Device Controller drivers and
updating all existing USB drivers to use the new USB API:
1) A brief feature list:
- A new and mutex enabled USB API.
- Many USB drivers are now running Giant free.
- Linux USB kernel compatibility layer.
- New UGEN backend and libusb library, finally solves the "driver
unloading" problem. The new BSD licensed libusb20 library is fully
compatible with libusb-0.1.12 from sourceforge.
- New "usbconfig" utility, for easy configuration of USB.
- Full support for Split transactions, which means you can use your
full speed USB audio device on a high speed USB HUB.
- Full support for HS ISOC transactions, which makes writing drivers
for various HS webcams possible, for example.
- Full support for USB on embedded platforms, mostly cache flushing
and buffer invalidating stuff.
- Safer parsing of USB descriptors.
- Autodetect of annoying USB install disks.
- Support for USB device side mode, also called USB gadget mode,
using the same API like the USB host side. In other words the new
USB stack is symmetric with regard to host and device side.
- Support for USB transfers like I/O vectors, means more throughput
and less interrupts.
- ... see the FreeBSD quarterly status reports under "USB project"
2) To enable the driver in the default kernel build:
2.a) Remove all existing USB device options from your kernel config
file.
2.b) Add the following USB device options to your kernel configuration
file:
# USB core support
device usb2_core
# USB controller support
device usb2_controller
device usb2_controller_ehci
device usb2_controller_ohci
device usb2_controller_uhci
# USB mass storage support
device usb2_storage
device usb2_storage_mass
# USB ethernet support, requires miibus
device usb2_ethernet
device usb2_ethernet_aue
device usb2_ethernet_axe
device usb2_ethernet_cdce
device usb2_ethernet_cue
device usb2_ethernet_kue
device usb2_ethernet_rue
device usb2_ethernet_dav
# USB wireless LAN support
device usb2_wlan
device usb2_wlan_rum
device usb2_wlan_ral
device usb2_wlan_zyd
# USB serial device support
device usb2_serial
device usb2_serial_ark
device usb2_serial_bsa
device usb2_serial_bser
device usb2_serial_chcom
device usb2_serial_cycom
device usb2_serial_foma
device usb2_serial_ftdi
device usb2_serial_gensa
device usb2_serial_ipaq
device usb2_serial_lpt
device usb2_serial_mct
device usb2_serial_modem
device usb2_serial_moscom
device usb2_serial_plcom
device usb2_serial_visor
device usb2_serial_vscom
# USB bluetooth support
device usb2_bluetooth
device usb2_bluetooth_ng
# USB input device support
device usb2_input
device usb2_input_hid
device usb2_input_kbd
device usb2_input_ms
# USB sound and MIDI device support
device usb2_sound
2) To enable the driver at runtime:
2.a) Unload all existing USB modules. If USB is compiled into the
kernel then you might have to build a new kernel.
2.b) Load the "usb2_xxx.ko" modules under /boot/kernel having the same
base name like the kernel device option.
Submitted by: Hans Petter Selasky hselasky at c2i dot net
Reviewed by: imp, alfred
Also: Change the initialisation of the command string to a static
initialiser. Verify it against the output of umass.c when being sent a
command using 'camcontrol eject da0' to a Bulk-Only device.
This should make those devices work that need a SCSI eject command to
switch to modem mode (Novatel 950D and others).
allocating resources to read the CIS. I'm not sure when this changed,
but it is totally wrong. Also, add a minor improvement to the
debugging.
This should help everybody trying to run dumpcis on atheros wireless
card as well.
MFC after: 2 days
right... Good thing the size was ignored...
Where this macro is used, there's no reason to do it anyway. There
seems to have been some old-time confusion between the CIS pointer
definition, and the BAR definitions at the base of this bug.
compiled into the main AMR driver. It's code that is nice to have but not
required for normal operation, and it is reported to cause problems for some
people.
For an unknown reason the touch pad of my PowerBook generates button 5
events when you operate it. This causes the adb_mouse code to convert
them to button 2 events, which is not what we want.
Add a new flag, AMS_TOUCHPAD, which is used to distinguish the touch
pad. When set, don't convert button events of unknown buttons to the
last button.
There are still three problems left with respect to user input:
- The mouse button events are not properly processed when the touch pad
isn't touched.
- The arrow keys on the keyboard don't work inside X11.
- The power button isn't handled by the kernel, similar to the ACPI
power button on i386/amd64.
Approved by: nwhitehorn
use process ID as ACPI thread ID. Concurrent requests with equal thread
IDs broke ACPI mutexes operation causing unpredictable errors including
AE_AML_MUTEX_NOT_ACQUIRED that I have seen.
Use kernel thread ID instead of process ID for ACPI thread.
Right now ams_read() uses cv_wait() to wait for new data to arrive on
the mouse device. This means that when you run `cat /dev/ams0', it
cannot be interrupted directly. After you press ^C, you first need to
move the mouse before cat will quit. Make this function use
cv_wait_sig(), which allows it to be interrupted directly.
Reviewed by: nwhitehorn
capabilities reported by the ap. These need to be cross-checked
against the local configuration in the vap. Previously we were
only checking the ap capabilities which meant that if an ap reported
it was ff-capable but we were not setup to use them we'd try to do
ff aggregation and drop the frame.
There are a number of problems to be fixed here but applying this
fix immediately as the problem causes all traffic to stop (and has
not workaround).
Reported by: Ashish Shukla
sdhci supports up to 65535 blocks transfers, at91_mci - one block.
Enable multiblock operations disabled before to follow at91_mci driver
limitations.
Reviewed by: imp@
driver (rev 1.3), by Joerg Sonnenberger.
Note: This change is untested as I do not own the hardware. Let me know
if things work or do not work for you by sending me the output dmesg (and
usbctl -f /dev/usbX if possible). Thanks.
for the BCM5714 revision A0 when in a multi-port configuration
and unconditionally for the remainder of the class of BCM575X
and beyond chips.
This was prodded by mav and is based on a suggestion and a
patch submitted by jhb.
Reviewed by: jhb
MFC after: 2 months
rs400/rs480 should clear the RADEON_BUS_MASTER_DIS bit. This should get
the rs485 IGP chips going again.
Approved by: jhb (mentor)
Obtained from: drm git master
making the use of sc_hwmap to do direct mapping impractical. Switch to
indexing by the rate index instead of the rate code and adjust associated
state and logic appropriately. This has several benefits including
simplification of the led code.
o fix radiotap capture of HT rates
o fix conditional compilation of HT radiotap support to be based on the
hal having 5416 support; not the ABI version as hal builds may or may
not include 5416 support
o update tx rssi data only when an ACK was received
o return tx rssi from sampled data instead of the last frame
o track noise floor
o return rx rssi and noise floor (was broken)
o pass country code, outdoor indication, and ecm mode into the hal
when requesting a channel list
o add a console msg when regulatory setup fails
o add placeholder code to map between Atheros sku's and 802.11 sku's
that handles only the debug country code used to unlock the full
channel list (to be used only for debugging)
o fix multiple instances of mismapping the 802.11 location to the
outdoor indication (anywhere may be outdoor also)
in sta and adhoc modes; this should've been done forever ago as most all
drivers use this hook to set per-station transmit parameters such as for
tx rate control
o adjust drivers to remove explicit calls to the driver newassoc method
The cn_unit and cn_tp fields don't seem to be used anywhere. Some
drivers set them, while others don't. Just remove them, in an attempt to
make our consdev code a little easier to understand.
G3 as well as the internal ADB keyboard and mice in PowerBooks and iBooks. This
also brings in Mac GPIO support, for which we should eventually have a better
interface.
Obtained from: NetBSD (CUDA and PMU drivers)
Olaf Kirch noticed that the i915_set_status_page() function of the i915
kernel driver calls ioremap with an address offset that is supplied by
userspace via ioctl. The function zeroes the mapped memory via memset
and tells the hardware about the address. Turns out that access to that
ioctl is not restricted to root so users could probably exploit that to
do nasty things. We haven't tried to write actual exploit code though.
It only affects the Intel G33 series and newer.
Approved by: bz (secteam)
Obtained from: Intel drm repo
Security: CVE-2008-3831
Memory Interface (CFI). The flash memory can be read and written
to through /dev/cfi# and an ioctl() exists so processes can read
the query information.
The driver supports the AMD and Intel command set, though only
the AMD command has been tested.
Obtained from: Juniper Networks, Inc.
with several points unappropriate for the present parser. This patch
disables input-to-output analog monitoring but instead fixes recording.
Tested by Tobias Grosser on ThinkPad T61p.
might make Qualcomm and Option cards (which have all endpoints in 1
interface) work.
- Change the USB buffer sizes to depend on the transfer speed. With UMTS
we use a buffer 384k / 1000 frames/sec * 50msecs =~ 15kB for example.
- Add a MODULE_VERSION statement
but I inadvertently overwrote the change when I synced to git. Commit
the fix in both places, so this doesn't happen again.
Approved by: jhb (mentor)
MFC after: 2 weeks
This update fixes a transmit bug in the multi-queue (MSI-X) firmware
which happens when RDMAs complete out of order, and provides
improved support for the new Myri10GE NIC models (10G-PCIE-8Bx)
Sponsored by: Myricom Inc.
MFC after:3 days
With our new TTY layer we use a two step device destruction procedure.
The TTY first gets abandoned by the device driver. When the TTY layer
notices all threads have left the TTY layer, it deallocates the TTY.
This means that the device unit number should not be reused before a
callback from the TTY layer to the device driver has been made. newbus
doesn't seem to support this concept (yet), so right now just add a
destructor with a big comment in it. It's not ideal, but at least it's
better than panicing.
Reported by: rnoland
Driver supports PCI devices with class 8 and subclass 5 according to
SD Host Controller Specification.
Update NOTES, enable module and static build.
Enable related mmc and mmcsd modules build.
Discussed on: mobile@, current@
other fixes:
- Add pointers back to device_t objects in softc structures instead
of storing the unit and using devclass_get_device().
- Add 'lpbb', 'pcf', 'pps', and 'vpo' child devices to every 'ppbus' device
instead of just the first one.
- Store softc pointers in si_drv1 of character devices instead of
pulling the unit number from the minor number and using
devclass_get_softc() and devclass_get_device().
- Store the LP_BYPASS flag in si_drv2 instead of encoding it in the minor
number.
- Destroy character devices for lpt(4) when detaching the device.
- Use bus_print_child_footer() instead of duplicating it in
ppbus_print_child() and fix ppbus_print_child()'s return value.
- Remove unused AVM ivar from ppbus.
- Don't store the 'mode' ivar in the ppbus ivars since we always fetch it
from the parent anyway.
- Try to detach all the child devices before deleting them in
ppbus_detach().
- Use pause() instead of a tsleep() on a dummy address when polling the
ppbus.
- Use if_printf() and device_printf() instead of explicit names with unit
numbers.
Silence on: current@
Erase operation gives card's logic information about unused areas to help it
implement wear-leveling with lower overhead comparing to usual writing.
Erase is much faster then write and does not depends on data bus speed.
Also as result of hitting in-card write logic optimizations I have measured
up to 50% performance boost on writing undersized blocks into preerased areas.
At the same time there are strict limitations on size and allignment of erase
operations. We can erase only blocks aligned to the erase sector size and
with size multiple of it. Different cards has different erase sector size
which usually varies from 64KB to 4MB. SD cards actually allow to erase
smaller blocks, but it is much more expensive as it is implemented via
read-erase-write sequence and so not sutable for the BIO_DELETE purposes.
Reviewed by: imp@
(still a power of 2) rather than 63k transfers. Even with 63k transfers
some machines (such as Dell SC1435's) were experiencing chronic data
corruption.
- Use the MIO method to talk to the Serverworks HT1000_S1 SATA controller
like all the other SATA controllers rather than the compat PATA
method. This lets the controller see all 4 SATA ports and also
matches the behavior of the Linux driver.
Silence from: sos
MFC after: 3 days
bank instead of copper/fiber bank which in turn resulted in
wrong registers were accessed during PHY operation. It is
believed that page 0 should be used for copper PHY so reinitialize
E1000_EADR to select default copper PHY.
This fixes link establishment issue of nfe(4) on Sun Fire X4140.
OpenBSD also has similimar patch but they just reset the E1000_EADR
register to page 0. However some Marvell PHYs((88E3082, 88E1000)
don't have the extended address register and the meaning of the
register is quite different for each PHY model. So selecting copper
PHY is limited to 88E1149 PHY which seems to be the only one that
exhibits link establishment problem. If parent device know the type
of PHY(either copper or fiber) that information should be notified
to PHY driver but there is no good way to pass this information yet.
Reported by: thompsa
Reviewed by: thompsa
the Sierra and Novatel devices, ignore all umass devices and hide the umass
devices that represent the CD ROM devices (but not the SD card slot in the
Huawei Mobile dongle).
Note: This driver in FBSD7 seems to suffer from memory corruption when used
with an Option GT Quad. The E220 however works flawlessly.
Also add the ID for the Option GTMaxHSUPA, provided by Olivier Fromme.
o better quality of the movement smoothing
o more features such as tap-hold and virtual scrolling
Support must still be enabled with this line in your /boot/loader.conf:
hw.psm.synaptics_support="1"
The following sysctls were removed:
hw.psm.synaptics.low_speed_threshold
hw.psm.synaptics.min_movement
hw.psm.synaptics.squelch_level
An overview of this new driver and a short documentation about the added
sysctls is available on the wiki:
http://wiki.freebsd.org/SynapticsTouchpad
simplifies certain device attachments (Kauai ATA, for instance), and makes
possible others on new hardware.
On G5 systems, there are several otherwise standard PCI devices
(Serverworks SATA) that will not allow their interrupt properties to be
written, so this information must be supplied directly from Open Firmware.
Obtained from: sparc64
This supports 1Gbps Ethernet engine found on ARM-based SOCs (Orion, Kirkwood,
Discovery), as well as on system controllers for PowerPC processors (MV64430,
MV6446x).
The following advanced features are supported:
- multicast
- VLAN tagging
- IP/TCP/UDP checksum calculation offloading
- polling
- interrupt coalescing
Obtained from: Marvell, Semihalf
the last byte of the ethernet address was not read which in turn
resulted in getting 5 out of the 6 bytes of ethernet address and
always returned ENOENT. I did not notice the bug on FPGA version
because of additional configuration data in EEPROM.
Pointed out by: bouyer at NetBSD
example the Huawei Mobile has an SD card slot on the second interface.
- Do not attach to Qualcomm and Novatel cards. If ignored these cards will
switch to modem mode automatically it seems.
- Reduce the priority on generic attachment to the appropriate level.
Note: A better solution is to send an eject command straightaway, but that can
be left till later.
* Orion
- 88F5181
- 88F5182
- 88F5281
* Kirkwood
- 88F6281
* Discovery
- MV78100
The above families of SOCs are built around CPU cores compliant with ARMv5TE
instruction set architecture definition. They share a number of integrated
peripherals. This commit brings support for the following basic elements:
* GPIO
* Interrupt controller
* L1, L2 cache
* Timers, watchdog, RTC
* TWSI (I2C)
* UART
Other peripherals drivers will be introduced separately.
Reviewed by: imp, marcel, stass (Thanks guys!)
Obtained from: Marvell, Semihalf
will ease the identification of memory leaks as the OS will be able to track
allocations for us by malloc type. vmstat -m will show all of the
allocations.
Convert the calls to drm_alloc() and friends, which are used in shared code
to static __inline__ while we are here.
Approved by: jhb (mentor)
from operating on a list with a single item. This code is used much more by
the i915 driver with xorg-7.4. Correct it to match the actual linux
implementation.
Approved by: jhb (mentor)
busmastering support. This also adds register definitions for MSI support,
which we will be using shortly.
Approved by: jhb (mentor)
Obtained from: drm git master
macio's enable-enet word, which apparently does nothing on some machines,
open an OF instance of the ethernet controller. This fixes cold booting
from disk on my Blue & White G3.
MFC after: 3 days
device id is JMC260 family. Previously it just verified the deivce
is JMC260 Rev A0. This will make it easy for newer JMC2xx support.
Pointed out by: bouyer at NetBSD
