over iteration of their multicast address lists when synchronizing the
hardware address filter with the network stack-maintained list.
Problem reported by: Ed Maste (emaste at phaedrus dot sandvine dot ca>
MFC after: 1 week
support for them can really be added. Eliminate the check for network
card, because many of the cards in the commented out section are combo
cards and report themselves as either multifunction or modem. They
will be added back as I obtain hardware and test them more fully.
few other cards need. This firmware was obtained from the Linux
pcmica-cs project, but Ositech Communications, Inc has been kind
enough to grant permission to change the license to a pure BSDL type.
that since I can't test it directly. The driver also lists the EM1144
as being supported, but in reality it isn't. The EM1144-T,
{XJ,CC}{3288,3336} have the SMC chips in them, but aren't conformant MFC
cards, so they need their own driver.
Also, it does little harm to list the 8020BT, so remove #if 0.
Approved by: re (scottl)
Move ethernet MAC address setting into pccard attachment
Fix panic from IFP2ENADDR() use prior to if_alloc
Remove OLDCARD compat support. This should work still on oldcard, however.
sn_attach now requires that the resources be activated now, so adjust.
Approved by: re (scottl)
Provide a backwards compatible way to have the extra macro by defining
PCCARD_API_LEVEL 5 before including pccarddevs for driver writers that
want/need to have the same driver on 5 and 6 with pccard attachments.
Approved by: re (dwhite)
struct ifnet or the layer 2 common structure it was embedded in have
been replaced with a struct ifnet pointer to be filled by a call to the
new function, if_alloc(). The layer 2 common structure is also allocated
via if_alloc() based on the interface type. It is hung off the new
struct ifnet member, if_l2com.
This change removes the size of these structures from the kernel ABI and
will allow us to better manage them as interfaces come and go.
Other changes of note:
- Struct arpcom is no longer referenced in normal interface code.
Instead the Ethernet address is accessed via the IFP2ENADDR() macro.
To enforce this ac_enaddr has been renamed to _ac_enaddr.
- The second argument to ether_ifattach is now always the mac address
from driver private storage rather than sometimes being ac_enaddr.
Reviewed by: sobomax, sam
there's not dependencies on pccard symboles, such a dependency is not
necessary. This means that drivers that have multiple attachments can
not drag bogus devices into the kernel at load time.
We can't (yet) do this with pci and isa. Drivers written for them
actually do seem to have symbols that depend on these busses'
implementation code.
ndis not touched until other things can be tested.
if the link-level address has been initialized already.
The majority of modern drivers never does this and works fine, which
makes me think that the check is totally unnecessary and a residue
of cut&paste from other drivers.
This change is done to simplify locking because now almost none of the
drivers uses this field. The exceptions are "ct" "ctau" and "cx"
where i am not sure if i can remove that part.
multicast hash are written. There are still two distinct algorithms used,
and there actually isn't any reason each driver should have its own copy
of this function as they could all share one copy of it (if it grew an
additional argument).
crashes that had sn0 as the irq that's being serviced, when there was
no sn0 in the system. This seems to prevent them. Also, we want to
wait until after we've registered with the network layer before we
turn on the interrupt spigot to avoid races.
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
Make the pccard attachment work with NEWCARD
Start locking of the driver, but only the macros are defined right now
Tested on: Megahertz CC10BT/2
# (These cards are very popular on ebay these days, and run < $10 including
# shipping from some sellers).
network layer (ether).
- Don't abuse module names to facilitate ifconfig module loading;
such abuse isn't really needed. (And if we do need type information
associated with a module then we should make it explicit and not
use hacks.)
o don't strip the Ethernet header from inbound packets; pass packets
up the stack intact (required significant changes to some drivers)
o reference common definitions in net/ethernet.h (e.g. ETHER_ALIGN)
o track ether_ifattach/ether_ifdetach API changes
o track bpf changes (use BPF_TAP and BPF_MTAP)
o track vlan changes (ifnet capabilities, revised processing scheme, etc.)
o use if_input to pass packets "up"
o call ether_ioctl for default handling of ioctls
Reviewed by: many
Approved by: re
