Summary:
Migrate to using the semi-opaque type rman_res_t to specify rman resources. For
now, this is still compatible with u_long.
This is step one in migrating rman to use uintmax_t for resources instead of
u_long.
Going forward, this could feasibly be used to specify architecture-specific
definitions of resource ranges, rather than baking a specific integer type into
the API.
This change has been broken out to facilitate MFC'ing drivers back to 10 without
breaking ABI.
Reviewed By: jhb
Sponsored by: Alex Perez/Inertial Computing
Differential Revision: https://reviews.freebsd.org/D5075
When the system has more than a single PCI domain, the bus numbers
are not unique, thus they cannot be used for "pci" device numbering.
Change bus numbers to -1 (i.e. to-be-determined automatically)
wherever the code did not care about domains.
Reviewed by: jhb
Obtained from: Semihalf
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3406
and start teaching subsystems about it.
The Atheros MIPS platforms don't guarantee any kind of FIFO consistency
with interrupts in hardware. So software needs to do a flush when it
receives an interrupt and before it calls the interrupt handler.
There are new ones for the QCA934x and QCA955x, so do a few things:
* Get rid of the individual ones (for ethernet and IP2);
* Create a mux and enum listing all the variations on DDR flushes;
* replace the uses of IP2 with the relevant one (which will typically
be "PCI" here);
* call the USB DDR flush before calling the real USB interrupt handlers;
* call the ethernet one upon receiving an interrupt that's for us,
rather than never calling it during operation.
Tested:
* QCA9558 (TP-Link archer c7 v2)
* AR9331 (Carambola 2)
TODO:
* PCI, USB, ethernet, etc need to do a double-check to see if the
interrupt was truely for them before doing the DDR. For now I
prefer "correct" over "fast".
return BUS_PROBE_NOWILDCARD from their probe routines to avoid claiming
wildcard devices on their parent bus. Do a sweep through the MIPS tree.
MFC after: 2 weeks
* Mikrotik RouterBoard 433AH have PCI slot 18 wired to INT0 on the PCI Bus.
This is different from e.g. Atheros PB42 and Ubiquiti boards.
* Check for hint hint.pcib.0.baseslot=X, where X is number of base slot;
* If hint not supplied print a warning and use default AR71XX_PCI_BASE_SLOT;
PR: kern/174978
Approved by: adrian (mentor)
ar724x_pci.c.
* Move out the code which populates the firmware into ar71xx_fixup.c
* Shuffle around the ar724x fixup code to match what the ar71xx fixup
code does.
I've validated this on an AR7240 with AR9285 on-board NIC. It doesn't
yet load, as the AR9285 EEPROM code needs to be made "flash aware."
TODO:
* Validate that I haven't broken AR71xx
* Test AR9285/AR9287 onboard NICs, complete with EEPROM code changes
* Port over the needed BAR hacks for AR7240, AR7241 and AR7242 from
Linux OpenWRT. The current WAR has only been tested on the AR7240
and I'm not sure the way the BAR register is treated is "right".
The "fixup" method here is right when setting the BAR for local access -
ie, the BAR address is either 0xffff (AR7240) or 0x1000ffff (AR7241/AR7242),
but the ath9k-fixup.c code (Linux OpenWRT) does this when setting the
initial "fixup" BAR. It then restores the original BAR.
I'll have to read the ar724x PCI bus glue to see what other special cases
await.
future use by the ath(4) driver.
These embedded devices put the calibration/PCI bootstrap data on the
on board SPI flash rather than on an EEPROM connected to the NIC.
For some boards, there's two NICs and two sets of EEPROM data in the
main SPI flash.
The particulars:
* Introduce ath_fixup_size, which is the size of the EEPROM area in
bytes.
* Create a firmware image with a name based on the PCI device identifier
(bus/slot/device/function).
* Hide some verbose debugging behind 'bootverbose'.
ath(4) can then use this to load in the EEPROM data.
This requires AR71XX_ATH_EEPROM to be defined.
* the openwrt code doesn't treat 0/0/0 any differently
from other bus/slot/func combinations.
* A "local write" function writes to the LCONF area, and
so I've added it.
* The PCI workaround at attach time uses this LCONF code,
which it already did ..
* .. but it is a 4 byte write, not a 2 byte write.
Even though it's PCIR_COMMAND which is a two byte PCI register.
Tested on: AR7161
TODO: The other two AR71xx derivatives
TODO: More thoroughly stare at the datasheets I do have
and if it indeed is incorrect, push fixes to both
FreeBSD and Linux/OpenWRT.
Obtained from: Linux OpenWRT
on-board, glued to the AR71xx CPU. These may forgo separate WMAC EEPROMs
(which store configuration and calibration data) and instead store
it in the main board SPI flash.
Normally the NIC reads the EEPROM attached to it to setup various PCI
configuration registers. If this isn't done, the device will probe as
something different (eg 0x168c:abcd, or 0x168c:ff??.) Other setup registers
are also written to which may control important functions.
This introduces a new compile option, AR71XX_ATH_EEPROM, which enables the
use of this particular code. The ART offset in the SPI flash can be
specified as a hint against the relevant slot/device number, for example:
hint.pcib.0.bus.0.17.0.ath_fixup_addr=0x1fff1000
hint.pcib.0.bus.0.18.0.ath_fixup_addr=0x1fff5000
TODO:
* Think of a better name;
* Make the PCIe version of this fixup code also use this option;
* Maybe also check slot 19;
* This has to happen _before_ the SPI flash is set from memory-mapped
to SPI-IO - so document that somewhere.
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.
