told to use IRQ 6, progam the pcic to use irq 7 instead. Evidentally,
at least some of the cards are wired this way. If you want to use irq
6, configure it. All the mapping is done just before we set the
interrupt registers. See [FreeBSD98-testers 5064] for details.
Added commentary about valid interrupts on some CBUS pc98 CL PD6722
based cards.
Submitted by: Hiroshi TSUKADA-san <hiroshi@kiwi.ne.jp>
built in, or as an addon card (My Japanese isn't quite good enough to
know which). [FreeBSD98-testers 5098] contains all the details.
Submitted by: Kawanobe Koh-san <kawanobe@st.rim.or.jp>
(I'll be we know which compiler and platform they developed this on...)
Minimally change them to C89 comments to make GCC happy. (this is kinda funny
as the file has piece derived from FreeBDS 3.2)
Also fix FreeBSD id style.
The DP83820/83821 has an undocumented limitation concerning jumbo frames
and TX checksum offload. In order for TX checksum offload to work, the
outgoing frame must fit entirely within the TX FIFO, which is 8192 bytes
in size. This isn't a problem, until you try to send a 9000-byte frame,
at which point the TX DMA engine goes to sleep. It turns out that if
you want to send a jumbo frame larger than 8170 bytes (8192 - 64), you
have to turn off the TX checksum support.
As a workaround, I changed nge_ioctl() so that if the user selects an
MTU larger than 8152 bytes, we clear the if_hwassist flags. The flags
will be set again once the MTU is reduced to a smaller value.
- Use db_printf() instead of printf().
- Clean up decode_syscall() to use regular if-then-else rather than goto's.
- Use the same method of parsing PID's for per-process traces as the x86
code does: that is, if the address passed in is not a valid kernel
address, treat it is a decimal pid.
- If the pid of the current process is specified, fall back to using the
"default" parameters for the trace as curproc's pcb is not valid at this
point.
MFC after: 1 week
we want the checksums calculated on a per-packet basis using control bits
in the extsts field of the DMA descriptor structure. For TX, the chip
seems to want these bits set in the field of the first descriptor in
a fragment chain, not the last.
412: warning: long unsigned int format, unsigned int arg (arg 3)
418: warning: long unsigned int format, unsigned int arg (arg 3)
424: warning: long unsigned int format, unsigned int arg (arg 3)
take a const 'name', since they dont modify anything.
159: warning: passing arg 1 of `getenv_int' discards qualifiers...
167: warning: passing arg 1 of `getenv' discards qualifiers from pointer..
vinumhdr.h:80: warning: redundant redeclaration of `vinum_cdevsw'
vinumext.h:239: warning: previous declaration of `vinum_cdevsw'
in each of the following files:
vinum.c, vinumconfig.c, vinumdaemon.c, vinuminterrupt.c, vinumio.c,
vinumioctl.c, vinumlock.c, vinummemory.c, vinumraid5.c, vinumrequest.c,
vinumrevive.c, vinumstate.c, vinumutil.c
musycc.c:449: warning: long unsigned int format, unsigned int arg (arg 3)
musycc.c:449: warning: long unsigned int format, unsigned int arg (arg 4)
musycc.c:453: warning: long unsigned int format, unsigned int arg (arg 3)
musycc.c:453: warning: long unsigned int format, unsigned int arg (arg 4)
musycc.c:453: warning: long unsigned int format, unsigned int arg (arg 5)
These warnings used to be confined to the alpha but are on all now.
554: passing arg 4 of `resource_string_value' from incompatible pointer type
576: passing arg 4 of `resource_string_value' from incompatible pointer type
593: passing arg 4 of `resource_string_value' from incompatible pointer type
commands that complete (with no apparent error) after
we receive a LIP. This has been observed mostly on
Local Loop topologies. To be safe, let's just mark
all active commands as dead if we get a LIP and we're
on a private or public loop.
MFC after: 4 weeks
could only get a chance of testing it under 4.3, but together with the
if_oltr.c fixes at least it seems to work now. If someone has the chance
to test this under -current, please do.
Unfortunaltey, the TR code itself (if_iso88025subr.c) is not written
in a way that would allow to make a seaparate KLD out of it. By now,
just link it directly into the oltr KLD since it's probably the POLA
to be able to load the TR code together with the only TR hardware
driver we've got by now.
I've got one single unexplained panic (in doreti_switch or somewhere
there, calling a 0xc1XXXXXX address that did no longer belong to the
kernel at all) after unloading the modules once, thus i don't propose
a MFC of this module despite my testing has been done solely on 4.3,
unless someone is really going to test this stuff in -current.
This avoids a null pointer deref panic in TRlldClose() inside the
vendor-supplied object code. It's now possible to unload the driver
at all.
Implement deallocation of malloc()ed memory regions.
MFC after: 2 months
The symptom being treated in 1.98 was to avoid freeing a
pagedep dependency if there was still a newdirblk dependency
referencing it. That change is correct and no longer prints
a warning message when it occurs. The other part of revision
1.98 was to panic when a newdirblk dependency was encountered
during a file truncation. This fix removes that panic and
replaces it with code to find and delete the newdirblk
dependency so that the truncation can succeed.
cpu_mp_start() is never called, mp_ncpus will have a non-zero value.
This prevents systat from dying with an arithmatic exception caused
by a divide-by-zero error on UP alphas running a GENERIC kernel.
Replace the a.out emulation of 'struct linker_set' with something
a little more flexible. <sys/linker_set.h> now provides macros for
accessing elements and completely hides the implementation.
The linker_set.h macros have been on the back burner in various
forms since 1998 and has ideas and code from Mike Smith (SET_FOREACH()),
John Polstra (ELF clue) and myself (cleaned up API and the conversion
of the rest of the kernel to use it).
The macros declare a strongly typed set. They return elements with the
type that you declare the set with, rather than a generic void *.
For ELF, we use the magic ld symbols (__start_<setname> and
__stop_<setname>). Thanks to Richard Henderson <rth@redhat.com> for the
trick about how to force ld to provide them for kld's.
For a.out, we use the old linker_set struct.
NOTE: the item lists are no longer null terminated. This is why
the code impact is high in certain areas.
The runtime linker has a new method to find the linker set
boundaries depending on which backend format is in use.
linker sets are still module/kld unfriendly and should never be used
for anything that may be modular one day.
Reviewed by: eivind
- Replace some very poorly thought out API hacks that should have been
fixed a long while ago.
- Provide some much more flexible search functions (resource_find_*())
- Use strings for storage instead of an outgrowth of the rather
inconvenient temporary ioconf table from config(). We already had a
fallback to using strings before malloc/vm was running anyway.
Following changed was made by previous commit:
- add a pointer to struct mauxtag. two integer was too restrictive.
- add m_aux_{add,find}2.
- make sure to nuke mbuf pointed to m_aux.
This work was based on kame-20010528-freebsd43-snap.tgz and some
critical problem after the snap was out were fixed.
There are many many changes since last KAME merge.
TODO:
- The definitions of SADB_* in sys/net/pfkeyv2.h are still different
from RFC2407/IANA assignment because of binary compatibility
issue. It should be fixed under 5-CURRENT.
- ip6po_m member of struct ip6_pktopts is no longer used. But, it
is still there because of binary compatibility issue. It should
be removed under 5-CURRENT.
Reviewed by: itojun
Obtained from: KAME
MFC after: 3 weeks
. remove stale comments and a stale #define (from the old days of ft(4))
. make MAX_SEC_SIZE (used in isa_dmainit()) a #define
. fix a typo in a string
. use 0 as the blocksize in devstat_add_entry(), since the actual blocksize
is unknown (devstat(9) suggests to use 0 in that case)
out nearly every platform but the one I tested on requires the intpin
to swizzle out the correct intline.
tested by: Martijn Pronk <mpkisbkl@xs4all.nl> (lca_pci)
page of the image to load section headers and if we let the text section
start at zero, it corrupts the section table when its loaded. With this
change, the loader gets as far as the 'ok' prompt.
processes a little earlier to avoid a deadlock. Second, when calculating
the 'largest process' do not just count RSS. Instead count the RSS + SWAP
used by the process. Without this the code tended to kill small
inconsequential processes like, oh, sshd, rather then one of the many
'eatmem 200MB' I run on a whim :-). This fix has been extensively tested on
-stable and somewhat tested on -current and will be MFCd in a few days.
Shamed into fixing this by: ps
greatly improved traceback code from Ross Harvey. This code
requires the use of more traceback friendly temporary labels
at kernel entry points, hence the changes to exception.s and
asm.h
Reviewed by: jhb, dfr
Obtained from: NetBSD
MFC after: 1 week
higher chips. Treat it as if it were a 113x. This is correct as far
as 16-bit cards go, at least how we're using it.
# It appears that my TI-1031 based pci card that YAMAMOTO shigeru-san gave
# me on my trip to Japan now works.
around, use a common function for looking up and extracting the tunables
from the kernel environment. This saves duplicating the same function
over and over again. This way typically has an overhead of 8 bytes + the
path string, versus about 26 bytes + the path string.
use of the extsts field in DMA descriptors. We need this to tell the chip
to calculate TCP/IP checksums in hardware on a per-packet basis.
- Fix the unions in DMA descriptor structures. Breakage on alpha led
me to realize I'd done it wrong the first time.
that device add/remove will work without usbd running. usbd is still
used for execing stuff, but that is all now. Ideally it could be replaced
by a devd some day. Until now, usbd had to be running so that the
USB_DISCOVER ioctl could be called to walk the tree when an attachment
status change was noticed.
Among the changes:
- when a detach happens, remove any pending 'attach' messages or the system
suffers from whiplash from exec moused / kill moused loops if you do lots
of attach/detach and later start usbd.
- tweaks related to kthread differences
- disable the select handler for the old interface (never return success).
I have not removed it yet or old usbd's will abort. That can get removed
later once usbd is cleaned up and things have stabilized for a few weeks.
- get Giant in the kthread.
- a couple of minor potential bug fixes (usb_nevents vs malloc failure etc)
Pre-approved by: n_hibma (ages and ages ago)
One way we can reduce the amount of traffic we send in response to a SYN
flood is to eliminate the RST we send when removing a connection from
the listen queue. Since we are being flooded, we can assume that the
majority of connections in the queue are bogus. Our RST is unwanted
by these hosts, just as our SYN-ACK was. Genuine connection attempts
will result in hosts responding to our SYN-ACK with an ACK packet. We
will automatically return a RST response to their ACK when it gets to us
if the connection has been dropped, so the early RST doesn't serve the
genuine class of connections much. In summary, we can reduce the number
of packets we send by a factor of two without any loss in functionality
by ensuring that RST packets are not sent when dropping a connection
from the listen queue.
Submitted by: Mike Silbersack <silby@silby.com>
Reviewed by: jesper
MFC after: 2 weeks
not behaving correctly. Fix by attaching to the correct socket.
Also call so{rw}wakeup in addition to the fifo wakeup, so that any
kqfilters attached to the socket buffer get poked.
is usually (always?) used in expressions like (KTR_COMPILE & KTR_FOO).
Defining it as KTR_INTR|KTR_PROC gave the wrong value in approximately
8497 places according to error output for compiling LINT.
ep driver. The rest of the patch will wait until I can put the time
into it to get it righter than the kludge it is.
This protects us against card eject problems at all times,e xecpt when
we're in the epintr ISR.
PCN_BCR_CLRBIT(sc, PCN_BCR_MIICTL, PCN_MIICTL_DANAS);
should be:
PCN_BCR_SETBIT(sc, PCN_BCR_MIICTL, PCN_MIICTL_DANAS);
Turning this bit on is what disables MII autoneg, not turning it off.
Without this, manually setting the media doesn't work.
Noticed by: Jim Browne <jbrowne@jbrowne.com>
true. This permits better interoperability with programs which register
filters on their stdin/stdout handles.
Submitted by: Niels Provos <provos@citi.umich.edu>
I think bde even reviewed it once.
Also, change the name of ActionTEC pat to more generic Lucent Kermit
chip. Add stub for Xircom card. Add cardbus attachment too.
compliant. All the variable definitions and function names are
reasonably consistent, and the functions which should be static (i.e.,
all of them) are. Other assorted fixes were made. The majority of
the delta is indentation fixes.
Partially reviewed by: bde
incorrect due to a missing check for some dependency. This change
avoids the freelist corruption (but not the temporarily inconsistent
state of the file system).
A message is printed as a reminder of the under lying problem when a
pagedep structure is not freed due to the NEWBLOCK flag being set.
Submitted by: Tor.Egge@fast.no
can be made userland-visible as <dev/ic/...>. Also, those files are
not supposed to contain any bus-specific details at all, so placing
them under .../isa/ has been a misnomer from the beginning.
The files in src/sys/dev/ic/ have been repo-copied from their old
location (this commit is a forced null commit there to record this
message).
elected to do this in the probe rather than the attach so that we don't
disturb things which this might reset. different cards have different
quirks, according to their datasheets.
This should fix the "I booted in windows and rebooted to FreeBSD and
now things don't work" problem.
PR: 4847, 20670
route in ifa_ifwithroute(), as the last resort, look up the route to
the gateway, not destination (to derive the interface from).
PR: kern/27852
Submitted by: Iasen Kostoff <tbyte@tbyte.org>
MFC after: 2 weeks
