- Ask the user up to X times (3 by default) for the pass-phrase, if
it is incorrect the first time.
- Add support for storing the lockfiles in another other directory
than /etc.
- Document that it is possible to override the location of each single
lockfile.
Approved by: pjd
if [ -z "${_rc_subr_loaded}" ]; then
_rc_subr_loaded="YES"
...
fi
in order to avoid re-interpreting rc.subr every time an rc.d
script is run. In my tests, this speeds up rc time by about
8-10%.
This class is used for detecting volume labels on file systems:
UFS, MSDOSFS (FAT12, FAT16, FAT32) and ISO9660.
It also provide native labelization (there is no need for file system).
g_label_ufs.c is based on geom_vol_ffs from Gordon Tetlow.
g_label_msdos.c and g_label_iso9660.c are probably hacks, I just found
where volume labels are stored and I use those offsets here,
but with this class it should be easy to do it as it should be done by
someone who know how.
Implementing volume labels detection for other file systems also should
be trivial.
New providers are created in those directories:
/dev/ufs/ (UFS1, UFS2)
/dev/msdosfs/ (FAT12, FAT16, FAT32)
/dev/iso9660/ (ISO9660)
/dev/label/ (native labels, configured with glabel(8))
Manual page cleanups and some comments inside were submitted by
Simon L. Nielsen, who was, as always, very helpful. Thanks!
Most notably, this cleans up messages when shutting down from
single user. In such a case there are usually no daemons running,
but their pid files are still in /var/run. This causes rc.d to
output diagnostics about daemons with pidfiles, but that are
not running.
again. This user/group is not required for install* targets, hence do not
add them to CHECK_UIDS/CHECK_GIDS in Makefile.inc1 (no need to annoy
people).
Discussed-on: -current
your (network) modules as well as any userland that might make sense of
sizeof(struct ifnet).
This does not change the queueing yet. These changes will follow in a
seperate commit. Same with the driver changes, which need case by case
evaluation.
__FreeBSD_version bump will follow.
Tested-by: (i386)LINT
ip6addrctl_enable is set to YES, address selection policy is installed
into kernel.
If there is /etc/ip6addrctl.conf, it is used for address selection
policy. Even if there is no /etc/ip6addrctl.conf, we install default
policy. In this case, if ipv6_enable is set to YES, we use address
selection policy described in RFC 3484 as default. Otherwise, we
install priority policy for IPv4 address.
The default of ip6addrctl_enable is NO for now. However, it may
better to enable it by default.
/usr/local/www
[1] Semi-arbitrary cutoff, but I didn't want to add every locale directory
used by ports, because a lot are only used by one or two, and it's less
intrusive for these ports to just clean up after themselves.
MFC after: 2 days
The reason for doing this is that (at least some) 4.x binaries are very
unhappy if host.conf does not exist, and if we create host.conf but not
nsswitch.conf, nsswitch.conf will be created at the next reboot, so it
is better to create a correct nsswitch.conf right away.
use the conf/* stuff for their firewall configuration.
Running ipfw before could seem to make sense in that it would allow
one to setup access to the NFS server on a "default-deny" kernel,
but it is pretty obvious to the casual observer that such a configuration
never makes it far enough to mount the NFS-root in the first place.
debug.watchdog since it is not created by hardware watchdog(4) devices.
The watchdog(4) device is always compiled in the kernel, so removing the
check should not cause any problems.
Approved by: phk
