lnc(4) on PC98 and i386. The ISA front-end supports the same non-PNP
network cards as lnc(4) did and additionally a couple of PNP ones.
Like lnc(4), the C-bus front-end of le(4) only supports C-NET(98)S
and is untested due to lack of such hardware, but given that's it's
based on the respective lnc(4) and not too different from the ISA
front-end it should be highly likely to work.
- Remove the descriptions of le(4), which where converted from lnc(4),
from sys/i386/conf/NOTES and sys/pc98/conf/NOTES as there's a common
one in sys/conf/NOTES.
entry to the PCI NICs section so it's in the same spot in all GENERIC
config files.
- Add a note to the description of pcn(4) informing that is has precedence
over le(4).
o Properly use rman(9) to manage resources. This eliminates the
need to puc-specific hacks to rman. It also allows devinfo(8)
to be used to find out the specific assignment of resources to
serial/parallel ports.
o Compress the PCI device "database" by optimizing for the common
case and to use a procedural interface to handle the exceptions.
The procedural interface also generalizes the need to setup the
hardware (program chipsets, program clock frequencies).
o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by
default and non-serdev devices are handled by the bus.
o Use the serdev I/F to collect interrupt status and to handle
interrupts across ports in priority order.
o Sync the PCI device configuration to include devices found in
NetBSD and not yet merged to FreeBSD.
o Add support for Quatech 2, 4 and 8 port UARTs.
o Add support for a couple dozen Timedia serial cards as found
in Linux.
end for isa(4).
o Add a seperate bus frontend for acpi(4) and allow ISA DMA for
it when ISA is configured in the kernel. This allows acpi(4)
attachments in non-ISA configurations, as is possible for ia64.
o Add a seperate bus frontend for pci(4) and detect known single
port parallel cards.
o Merge PC98 specific changes under pc98/cbus into the MI driver.
The changes are minor enough for conditional compilation and
in this form invites better abstraction.
o Have ppc(4) usabled on all platforms, now that ISA specifics
are untangled enough.
Previously, we tried to allow this only for root. However, we were calling
suser() on the *target* process rather than the current process. This
means that if you can ptrace() a process running as root you can set a
hardware watch point in the kernel. In practice I think you probably have
to be root in order to pass the p_candebug() checks in ptrace() to attach
to a process running as root anyway. Rather than fix the suser(), I just
axed the entire idea, as I can't think of any good reason _at all_ for
userland to set hardware watch points for KVM.
MFC after: 3 days
Also thinks hardware watch points on KVM from userland are bad: bde, rwatson
interrupt handlers rather than BUS_SETUP_INTR() and BUS_TEARDOWN_INTR().
Uses of the BUS_*() versions in the implementation of foo_intr methods
in bus drivers were not changed. Mostly this just means that some
drivers might start printing diagnostic messages like [FAST] when
appropriate as well as honoring mpsafenet=0.
- Fix two more of the ppbus drivers' identify routines to function
correctly in the mythical case of a machine with more than one ppbus.
to COMPAT_43TTY.
Add COMPAT_43TTY to NOTES and */conf/GENERIC
Compile tty_compat.c only under the new option.
Spit out
#warning "Old BSD tty API used, please upgrade."
if ioctl_compat.h gets #included from userland.
param.h. Per request, I've placed these just after the
_NO_NAMESPACE_POLLUTION ifndef. I've not renamed anything yet, but
may since we don't need the __.
Submitted by: bde, jhb, scottl, many others.
passing a pointer to an opaque clockframe structure and requiring the
MD code to supply CLKF_FOO() macros to extract needed values out of the
opaque structure, just pass the needed values directly. In practice this
means passing the pair (usermode, pc) to hardclock() and profclock() and
passing the boolean (usermode) to hardclock_cpu() and hardclock_process().
Other details:
- Axe clockframe and CLKF_FOO() macros on all architectures. Basically,
all the archs were taking a trapframe and converting it into a clockframe
one way or another. Now they can just extract the PC and usermode values
directly out of the trapframe and pass it to fooclock().
- Renamed hardclock_process() to hardclock_cpu() as the latter is more
accurate.
- On Alpha, we now run profclock() at hz (profhz == hz) rather than at
the slower stathz.
- On Alpha, for the TurboLaser machines that don't have an 8254
timecounter, call hardclock() directly. This removes an extra
conditional check from every clock interrupt on Alpha on the BSP.
There is probably room for even further pruning here by changing Alpha
to use the simplified timecounter we use on x86 with the lapic timer
since we don't get interrupts from the 8254 on Alpha anyway.
- On x86, clkintr() shouldn't ever be called now unless using_lapic_timer
is false, so add a KASSERT() to that affect and remove a condition
to slightly optimize the non-lapic case.
- Change prototypeof arm_handler_execute() so that it's first arg is a
trapframe pointer rather than a void pointer for clarity.
- Use KCOUNT macro in profclock() to lookup the kernel profiling bucket.
Tested on: alpha, amd64, arm, i386, ia64, sparc64
Reviewed by: bde (mostly)
_MACHINE == i386 test always succeeds, even on non-i386 (both
sides of expressions become 0). Remove the comment since
_MACHINE and _MACHINE_ARCH are going away.
via the DEFAULTS kernel configs. This allows folks to turn it that option
off in the kernel configs if desired without having to hack the source.
This is especially useful since PUC_FASTINTR hangs the kernel boot on my
ultra60 which has two uart(4) devices hung off of a puc(4) device.
I did not enable PUC_FASTINTR by default on powerpc since powerpc does not
currently allow sharing of INTR_FAST with non-INTR_FAST like the other
archs.
IPI_STOP IPIs.
- Change the i386 and amd64 MD IPI code to send an NMI if STOP_NMI is
enabled if an attempt is made to send an IPI_STOP IPI. If the kernel
option is enabled, there is also a sysctl to change the behavior at
runtime (debug.stop_cpus_with_nmi which defaults to enabled). This
includes removing stop_cpus_nmi() and making ipi_nmi_selected() a
private function for i386 and amd64.
- Fix ipi_all(), ipi_all_but_self(), and ipi_self() on i386 and amd64 to
properly handle bitmapped IPIs as well as IPI_STOP IPIs when STOP_NMI is
enabled.
- Fix ipi_nmi_handler() to execute the restart function on the first CPU
that is restarted making use of atomic_readandclear() rather than
assuming that the BSP is always included in the set of restarted CPUs.
Also, the NMI handler didn't clear the function pointer meaning that
subsequent stop and restarts could execute the function again.
- Define a new macro HAVE_STOPPEDPCBS on i386 and amd64 to control the use
of stoppedpcbs[] and always enable it for i386 and amd64 instead of
being dependent on KDB_STOP_NMI. It works fine in both the NMI and
non-NMI cases.
originally wrote it for 4.x and hasn't really had the time to fully update
it to 5.x and later. Also, the author doesn't use the hardware anymore as
well. If someone does need this driver they can always resurrect it from
the Attic.
Requested by: Frank Mayhar frank at exit dot com
changes in MD code are trivial, before this change, trapsignal and
sendsig use discrete parameters, now they uses member fields of
ksiginfo_t structure. For sendsig, this change allows us to pass
POSIX realtime signal value to user code.
2. Remove cpu_thread_siginfo, it is no longer needed because we now always
generate ksiginfo_t data and feed it to libpthread.
3. Add p_sigqueue to proc structure to hold shared signals which were
blocked by all threads in the proc.
4. Add td_sigqueue to thread structure to hold all signals delivered to
thread.
5. i386 and amd64 now return POSIX standard si_code, other arches will
be fixed.
6. In this sigqueue implementation, pending signal set is kept as before,
an extra siginfo list holds additional siginfo_t data for signals.
kernel code uses psignal() still behavior as before, it won't be failed
even under memory pressure, only exception is when deleting a signal,
we should call sigqueue_delete to remove signal from sigqueue but
not SIGDELSET. Current there is no kernel code will deliver a signal
with additional data, so kernel should be as stable as before,
a ksiginfo can carry more information, for example, allow signal to
be delivered but throw away siginfo data if memory is not enough.
SIGKILL and SIGSTOP have fast path in sigqueue_add, because they can
not be caught or masked.
The sigqueue() syscall allows user code to queue a signal to target
process, if resource is unavailable, EAGAIN will be returned as
specification said.
Just before thread exits, signal queue memory will be freed by
sigqueue_flush.
Current, all signals are allowed to be queued, not only realtime signals.
Earlier patch reviewed by: jhb, deischen
Tested on: i386, amd64
