counterpart also takes, i.e. "fdx" for "full-duplex", "flow" for
"flowcontrol", "hdx" for "half-duplex" as well as "loop" and "loopback"
for "hw-loopback".
MFC after: 1 week
isn't configurable in a meaningful way. This is for ifconfig(8) or
other tools not to change code whenever IFT_USB-like interfaces are
registered at the interface list.
Reviewed by: brooks
No objections: gavin, jkim
in a comma delimited list instead of repeating "mediaopt" for each one.
This matches how the options of the active media are printed with
print_media_word() and brings us in line what NetBSD does.
MFC after: 2 weeks
use a different interface type (IFT_L2VLAN vs IFT_ETHER). Treat IFT_L2VLAN
interfaces like IFT_ETHER interfaces when handling link layer addresses.
Reviewed by: syrinx (bsnmpd)
MFC after: 1 week
interface considers that it hits a fatal error, and will not copyout
the request structure back for _IOW and _IOWR ioctls, keeping them
untouched.
The previous implementation of the SIOCGIFDESCR ioctl intends to
feed the buffer length back to userland. However, if we return
an error, the feedback would be defeated and ifconfig(8) would
trap into an infinite loop.
This commit changes SIOCGIFDESCR to set buffer field to NULL to
indicate the previous ENAMETOOLONG case.
Reported by: bschmidt
MFC after: 2 weeks
if the interface has such capability. The interface
capability flag indicates whether such capability
exists. This approach is much more backward compatible.
Physical device driver changes will be part of another
commit.
Also updated the ifconfig utility to show the LINKSTATE
capability if present.
Reviewed by: rwatson, imp, juli
MFC after: 3 days
non-digit character.
Due to an issue with rc(8) in a test configuration, ifconfig was being
invoked with the address used again as the width - for example,
ifconfig vlan0 10.0.0.1/10.0.0.1
Prior to this change, that address/width would be interpreted as
10.0.0.1/10.
regulatory domain with the "country" parameter, but will also take a full
country name. The man page warns that only the ISO code is unambiguous.
In reality, however, the first match on either would be accepted, leading
to "DE" being interpreted as the "DEBUG" country rather than Germany, and
"MO" selecting Morocco rather than the correct country, Macau.
Fix this by always checking for an ISO CC match first, and only search on
the full country name if that fails.
PR: bin/140571
Tested by: Dirk Meyer dirk.meyer dinoex.sub.org
Reviewed by: sam
Approved by: ed (mentor)
MFC after: 1 month
re-add $ipv6_enable support for backward compatibility. From
UPDATING:
1. To use IPv6, simply define $ifconfig_IF_ipv6 like $ifconfig_IF
for IPv4. For aliases, $ifconfig_IF_aliasN should be used.
Note that both variables need the "inet6" keyword at the head.
Do not set $ipv6_network_interfaces manually if you do not
understand what you are doing. It is not needed in most cases.
$ipv6_ifconfig_IF and $ipv6_ifconfig_IF_aliasN still work, but
they are obsolete.
2. $ipv6_enable is obsolete. Use $ipv6_prefer and/or
"inet6 accept_rtadv" keyword in ifconfig(8) instead.
If you define $ipv6_enable=YES, it means $ipv6_prefer=YES and
all configured interfaces have "inet6 accept_rtadv" in the
$ifconfig_IF_ipv6. These are for backward compatibility.
3. A new variable $ipv6_prefer has been added. If NO, IPv6
functionality of interfaces with no corresponding
$ifconfig_IF_ipv6 is disabled by using "inet6 ifdisabled" flag,
and the default address selection policy of ip6addrctl(8)
is the IPv4-preferred one (see rc.d/ip6addrctl for more details).
Note that if you want to configure IPv6 functionality on the
disabled interfaces after boot, first you need to clear the flag by
using ifconfig(8) like:
ifconfig em0 inet6 -ifdisabled
If YES, the default address selection policy is set as
IPv6-preferred.
The default value of $ipv6_prefer is NO.
4. If your system need to receive Router Advertisement messages,
define "inet6 accept_rtadv" in $ifconfig_IF_ipv6. The rc(8)
scripts automatically invoke rtsol(8) when the interface becomes
UP. The Router Advertisement messages are used for SLAAC
(State-Less Address AutoConfiguration).
automatic link-local address configuration:
- Convert a sysctl net.inet6.ip6.accept_rtadv to one for the
default value of a per-IF flag ND6_IFF_ACCEPT_RTADV, not a
global knob. The default value of the sysctl is 0.
- Add a new per-IF flag ND6_IFF_AUTO_LINKLOCAL and convert a
sysctl net.inet6.ip6.auto_linklocal to one for its default
value. The default value of the sysctl is 1.
- Make ND6_IFF_IFDISABLED more robust. It can be used to disable
IPv6 functionality of an interface now.
- Receiving RA is allowed if ip6_forwarding==0 *and*
ND6_IFF_ACCEPT_RTADV is set on that interface. The former
condition will be revisited later to support a "host + router" box
like IPv6 CPE router. The current behavior is compatible with
the older releases of FreeBSD.
- The ifconfig(8) now supports these ND6 flags as well as "nud",
"prefer_source", and "disabled" in ndp(8). The ndp(8) now
supports "auto_linklocal".
Discussed with: bz and jinmei
Reviewed by: bz
MFC after: 3 days
* don't clobber proxy entries
* HWMP seq number processing, including discard of old frames
* flush routing table entries based on nexthop
* print route flags in ifconfig
* more debugging messages and comments
Proxy changes submitted by sam.
Approved by: re (kib)
- fix ifconfig to ignore the non-existent interface in the current
network stack in case of '-vnet'.
- in ifconfig: actually use the local variables defined for the
vnet functions rather than modifying the global.
Reviewed by: rwatson
Approved by: re (kib)
* bridge support (sam)
* handling of errors (sam)
* deletion of inactive routing entries
* more debug msgs (sam)
* fixed some inconsistencies with the spec.
* decap is now specific to mesh (sam)
* print mesh seq. no. on ifconfig list mesh
* small perf. improvements
Reviewed by: sam
Approved by: re (kib)
net80211 wireless stack. This work is based on the March 2009 D3.0 draft
standard. This standard is expected to become final next year.
This includes two main net80211 modules, ieee80211_mesh.c
which deals with peer link management, link metric calculation,
routing table control and mesh configuration and ieee80211_hwmp.c
which deals with the actually routing process on the mesh network.
HWMP is the mandatory routing protocol on by the mesh standard, but
others, such as RA-OLSR, can be implemented.
Authentication and encryption are not implemented.
There are several scripts under tools/tools/net80211/scripts that can be
used to test different mesh network topologies and they also teach you
how to setup a mesh vap (for the impatient: ifconfig wlan0 create
wlandev ... wlanmode mesh).
A new build option is available: IEEE80211_SUPPORT_MESH and it's enabled
by default on GENERIC kernels for i386, amd64, sparc64 and pc98.
Drivers that support mesh networks right now are: ath, ral and mwl.
More information at: http://wiki.freebsd.org/WifiMesh
Please note that this work is experimental. Also, please note that
bridging a mesh vap with another network interface is not yet supported.
Many thanks to the FreeBSD Foundation for sponsoring this project and to
Sam Leffler for his support.
Also, I would like to thank Gateworks Corporation for sending me a
Cambria board which was used during the development of this project.
Reviewed by: sam
Approved by: re (kensmith)
Obtained from: projects/mesh11s
bits but isi_state did not follow; expand it to 32 bits and pad to
maintain alignment. Note this is an incompatible change that
requires rebuilding of user applications.
Submitted by: rpaulo, cbzimmer, avatar
version field sent via gif(4)+if_bridge(4). The EtherIP
implementation found on FreeBSD 6.1, 6.2, 6.3, 7.0, 7.1, and 7.2 had
an interoperability issue because it sent the incorrect EtherIP
packets and discarded the correct ones.
This change introduces the following two flags to gif(4):
accept_rev_ethip_ver: accepts both correct EtherIP packets and ones
with reversed version field, if enabled. If disabled, the gif
accepts the correct packets only. This flag is enabled by
default.
send_rev_ethip_ver: sends EtherIP packets with reversed version field
intentionally, if enabled. If disabled, the gif sends the correct
packets only. This flag is disabled by default.
These flags are stored in struct gif_softc and can be set by
ifconfig(8) on per-interface basis.
Note that this is an incompatible change of EtherIP with the older
FreeBSD releases. If you need to interoperate older FreeBSD boxes and
new versions after this commit, setting "send_rev_ethip_ver" is
needed.
Reviewed by: thompsa and rwatson
Spotted by: Shunsuke SHINOMIYA
PR: kern/125003
MFC after: 2 weeks
operations. This allows the query operations to work in non-IPv4 jails,
and will be necessary in a future of possible non-INET networking.
Approved by: bz (mentor)
that selects a callback from an interface prefix name. This allows us to
report a meaningful error when the user types 'ifconfig wlan0 create',
for example, and also kills some redundant code.
Reviewed by: sam (earlier version)