separate index variable.
It gives more then double rc4_init() performance increase on tested i386 P4.
It also gives about 15% speedup to PPTP VPN with stateless MPPE encryption
(by ng_mppc) which calls rc4_init() for every packet.
- Initialize variables before use.
- Remove a KASSERT() that could falsely trigger if there are other sources
of NMIs in the system.
Efficiency tweak:
- When checking PMCs that overflowed, ignore PMCs that were not configured for
sampling.
a real packet error but simply indicate that an unexpected unicast or multicast
error was received by the NIC, which was not counted in the past as well.
Reported by: many (on -stable@)
Reviewed by: davidch
MFC after: 3 days
On HyperThreading CPUs logical cores have same frequency, so setting it
on any core will change the other's one. In most cases first request
to the second core will be the "set" request, done after setting frequency
of the first core. In such case second CPU will obtain throttled frequency
of the first core as it's max_mhz making cpufreq broken due to different
frequency sets.
(e.g. ath): we must check the key index and not whether the key
points at a cipher other than "undef". This looks like it's been
broken for a while. Might be worth adding an explicit clear cipher
at some point though this would require changes to the usage of
IEEE80211_KEY_UNDEFINED.
PR: 125906
same LOM hardware with goofed-up EEPROM programming also needed reading the
Ethernet address from the chips registers as the EEPROM did not have a
sensible address programmed.
Patch developed by: pyun@
Funky hardware on loan: www.id-it.nl
MFC after: 2 weeks
the inpcb names rather than the following IPv6 compat macros:
in6pcb,in6p_sp, in6p_ip6_nxt,in6p_flowinfo,in6p_vflag,
in6p_flags,in6p_socket,in6p_lport,in6p_fport,in6p_ppcb and
sotoin6pcb().
Apart from removing duplicate code in netipsec, this is a pure
whitespace, not a functional change.
Discussed with: rwatson
Reviewed by: rwatson (version before review requested changes)
MFC after: 4 weeks (set the timer and see then)
controllers. Reading this register, for which there are indications
that it doesn't really exist, returns 0 on at least some 12160
and doing so on Sun Fire V880 causes a data access error exception.
Reported and tested by: Beat Gaetzi
Approved by: mjacob
Obtained from: OpenBSD (modulo setting isp_lvdmode)
the code for parsing interrupt maps) to PowerPC and reflect their new MI
status by moving them to the shared dev/ofw directory.
This commit also modifies the OFW PCI enumeration procedure on PowerPC to
allow the bus to find non-firmware-enumerated devices that Apple likes to add,
and adds some useful Open Firmware properties (compat and name) to the pnpinfo
string of children on OFW SBus, EBus, PCI, and MacIO links. Because of the
change to PCI enumeration on PowerPC, X has started working again on PPC
machines with Grackle hostbridges.
Reviewed by: marius
Obtained from: sparc64
1. separating L2 tables (ARP, NDP) from the L3 routing tables
2. removing as much locking dependencies among these layers as
possible to allow for some parallelism in the search operations
3. simplify the logic in the routing code,
The most notable end result is the obsolescent of the route
cloning (RTF_CLONING) concept, which translated into code reduction
in both IPv4 ARP and IPv6 NDP related modules, and size reduction in
struct rtentry{}. The change in design obsoletes the semantics of
RTF_CLONING, RTF_WASCLONE and RTF_LLINFO routing flags. The userland
applications such as "arp" and "ndp" have been modified to reflect
those changes. The output from "netstat -r" shows only the routing
entries.
Quite a few developers have contributed to this project in the
past: Glebius Smirnoff, Luigi Rizzo, Alessandro Cerri, and
Andre Oppermann. And most recently:
- Kip Macy revised the locking code completely, thus completing
the last piece of the puzzle, Kip has also been conducting
active functional testing
- Sam Leffler has helped me improving/refactoring the code, and
provided valuable reviews
- Julian Elischer setup the perforce tree for me and has helped
me maintaining that branch before the svn conversion
really was meant to be 256. Adjust usage accordingly and replace
bogus usage of this value in checking IEEE channel #'s.
NB: this causes an ABI change; ifconfig must be recompiled
indicates if an association id is required before outbound traffic
is permitted. This cleans up the previous change that broke mcast
traffic "to the stack" in ap mode as a side effect.
Reviewed by: sephe, thompsa, weongyo
src into the tree. The old split was balanced on module dependencies
and symbol exposure that no longer exists. Users that want a module
setup with rate control algorithm other than sample must override
ATH_RATE in the ath module Makefile.
Reviewed by: imp
to keep for 7-STABLE when MFCing in_pcbladdr() to not change the
behaviour there.
With this a destination route via a loopback interface is treated as
a valid and reachable thing for IPv4 source address selection, even
though nothing of that network is ever directly reachable, but it is
more like a blackhole route.
With this the source address will be selected and IPsec can grab the
packets before we would discard them at a later point, encapsulate them
and send them out from a different tunnel endpoint IP.
Discussed on: net
Reported by: Frank Behrens <frank@harz.behrens.de>
Tested by: Frank Behrens <frank@harz.behrens.de>
MFC after: 4 weeks (just so that I get the mail)
Remove ng_rmnode_flags() function.
ng_rmnode_self() was made to be called only while having node locked.
When node is properly locked, any function call sent to it will always be
queued. So turning ng_rmnode_self() into the ng_rmnode_flags() is not just
meaningless, but incorrent, as it violates node locking when called outside.
No objections: julian, thompsa
variable in this copy of the code[1].
While here prefix the variables with 'pf_' to avoid file static global
variables with colliding names that are or will be virtualized.
Discussed with: rwatson, silby [1]
by redoing the Open Firmware card initialization calls in ofwfb_set_mode(). This
uses the same trick (setting V_ADP_MODECHANGE) to arrange this as machfb(4) and
creatorfb(4).
but formerly missed under VIMAGE_GLOBAL.
Put the extern declarations of the virtualized globals
under VIMAGE_GLOBAL as the globals themsevles are already.
This will help by the time when we are going to remove the globals
entirely.
Sponsored by: The FreeBSD Foundation
time it is marked for user space callchain capture in the NMI
handler and the time the callchain capture callback runs.
- Improve code and control flow clarity by invoking hwpmc(4)'s user
space callchain capture callback directly from low-level code.
Reviewed by: jhb (kern/subr_trap.c)
Testing (various patch revisions): gnn,
Fabien Thomas <fabien dot thomas at netasq dot com>,
Artem Belevich <artemb at gmail dot com>
if (batt_sleep_ms)
AcpiOsSleep(1);
where the rest are all:
if (batt_sleep_ms)
AcpiOsSleep(batt_sleep_ms);
I can't recall why that one was different, so change it
to match the rest.
Pointed out by: Christoph Mallon
MFC after: 2 weeks
All ioctl()'s that aren't implemented by pts(4) are forwarded to the TTY
itself. Unfortunately this is not correct for FIONREAD, because it will
give the wrong amount of bytes that are available to read.
Tested by: keramida
Reminded by: keramida
On some laptops with smart batteries, enabling battery monitoring
software causes keystrokes from atkbd to be lost. This has also been
reported on Linux, and is apparently due to the keyboard and I2C line
for the battery being routed through the same chip. Whether that's
accurate or not, adding extra sleeps to the status checking code
causes the problem to go away.
I've been running this for nearly six months now on my laptop,
it works like a charm.
Reviewed by: Nate Lawson (in a previous revision)
MFC after: 2 weeks
o recognize ixp435 cpu
o change memory layout for for ixp4xx to not assume memory is aliases
to 0x10000000 (Cambria/ixp435 memory starts at zero)
o handle 64 irqs for ixp435
o dual EHCI USB 2.0 controller integral to ixp435
o overhaul NPE code for ixp435 and better MAC+MII naming
o updated NPE firmware (including NPE-A image for ixp435/ixp465)
o Gateworks Cambria board support:
- IDE compact flash
- MCU
- front panel LED on i2c bus
- Octal LED latch
Sanity-tested with NFS-root on Avila and Cambria boards. Requires
pending boot2 mods for CF-boot on Cambria.
error is not EAGAIN. Several sysctls that inspect another process use
p_candebug() for checking access right for the curproc. p_candebug()
returns EAGAIN for some reasons, in particular, for the process doing
exec() now. If execing process tries to lock Giant, we get a livelock,
because sysctl handlers are covered by Giant, and often do not sleep.
Break the livelock by dropping Giant and allowing other threads to
execute in the EAGAIN loop.
Also, do not return EAGAIN from p_candebug() when process is executing,
use more appropriate EBUSY error [1].
Reported and tested by: pho
Suggested by: rwatson [1]
Reviewed by: rwatson, des
MFC after: 1 week
state changes. This change modifies tunopen and tunclose to call the
if_link_state_change() function. Among other things, this will result in
devd(8) receiving events from devctl(4) for linkup/link down. This allows
us to do several useful things, including initializing tunnel parameters
and adding routes.
Discussed on: freebsd-net@
MFC after: 2 weeks
on a best-effort basis. Teach vn_fullpath to use this new VOP if a
regular VFS cache lookup fails. This VOP is designed to supplement the
VFS cache to provide a better chance that a vnode-to-name lookup will
succeed.
Currently, an implementation for devfs is being committed. The default
implementation is to return ENOENT.
A big thanks to kib for the mentorship on this, and to pho for running it
through his stress test suite.
Reviewed by: arch
Approved by: kib
One thing I didn't expect many applications to use, was kqueue() on
pseudo-terminal master devices. There are applications that use kqueue()
on the TTY itself (rtorrent, etc). That doesn't mean we shouldn't
implement this. Libraries like libevent use kqueue() by default, which
means they wouldn't be able to use kqueue().
The old TTY layer implements a very broken version of kqueue() by
performing the actual polling on the TTY device.
Discussed with: peter
When I added RLIMIT_NPTS, I forgot to add it to rlimit_ident[]. Make
sure the rlimit_ident[] array is always RLIM_NLIMITS elements big. So if
we ever forget to add new rlimits to this list again. it will contain a
null pointer, instead of random data.
Spotted by: rwatson
missed under VIMAGE_GLOBAL.
Start putting the extern declarations of the virtualized globals
under VIMAGE_GLOBAL as the globals themsevles are already.
This will help by the time when we are going to remove the globals
entirely.
While there garbage collect a few dead externs from ip6_var.h.
Sponsored by: The FreeBSD Foundation
o Try to be smarter about reading the ExCA CSC register. Now, we only
do it for 16-bit cards. Add some experimental code to treat it like
a power interrupt, but I'm not 100% sure that I like it. It may be
removed upon further testing. It seemed to help in one test case, but
the evidence may be inconclusive. This may be beneficial for cleaning up
exca_reset and exca_wait_ready.
o Check for CSTS events on the socket event register. We ask for it when
we're powering up a card, but I don't think we're otherwise using
it. Just ACK the interrupt for now. In theory, we can use it
instead of the busy wait we do in cbb_cardbus_reset. More research
is necessary to see if we can optimize things there when we're
waiting for the DEVVENDOR register to become valid.
o Rework the comments a bit. Minor tidying up. Etc.
outside the prison_states array.
When checking if there is a name configured for the prison, check the
first character to not be '\0' instead of checking if the char array
is present, which it always is. Note, that this is different for the
*jailname in the syscall.
Found with: Coverity Prevent(tm)
CID: 4156, 4155
MFC after: 4 weeks (just that I get the mail)
jhb probably forgot to commit this file with r185878 and will want to
review this. It unbreaks the build here.
Obtained from: p4 //depot/user/jhb/lock/compat/freebsd32/freebsd32_signal.h#2
container structures, depending on VIMAGE_GLOBALS compile time option.
Make VIMAGE_GLOBALS a new compile-time option, which by default will not
be defined, resulting in instatiations of global variables selected for
V_irtualization (enclosed in #ifdef VIMAGE_GLOBALS blocks) to be
effectively compiled out. Instantiate new global container structures
to hold V_irtualized variables: vnet_net_0, vnet_inet_0, vnet_inet6_0,
vnet_ipsec_0, vnet_netgraph_0, and vnet_gif_0.
Update the VSYM() macro so that depending on VIMAGE_GLOBALS the V_
macros resolve either to the original globals, or to fields inside
container structures, i.e. effectively
#ifdef VIMAGE_GLOBALS
#define V_rt_tables rt_tables
#else
#define V_rt_tables vnet_net_0._rt_tables
#endif
Update SYSCTL_V_*() macros to operate either on globals or on fields
inside container structs.
Extend the internal kldsym() lookups with the ability to resolve
selected fields inside the virtualization container structs. This
applies only to the fields which are explicitly registered for kldsym()
visibility via VNET_MOD_DECLARE() and vnet_mod_register(), currently
this is done only in sys/net/if.c.
Fix a few broken instances of MODULE_GLOBAL() macro use in SCTP code,
and modify the MODULE_GLOBAL() macro to resolve to V_ macros, which in
turn result in proper code being generated depending on VIMAGE_GLOBALS.
De-virtualize local static variables in sys/contrib/pf/net/pf_subr.c
which were prematurely V_irtualized by automated V_ prepending scripts
during earlier merging steps. PF virtualization will be done
separately, most probably after next PF import.
Convert a few variable initializations at instantiation to
initialization in init functions, most notably in ipfw. Also convert
TUNABLE_INT() initializers for V_ variables to TUNABLE_FETCH_INT() in
initializer functions.
Discussed at: devsummit Strassburg
Reviewed by: bz, julian
Approved by: julian (mentor)
Obtained from: //depot/projects/vimage-commit2/...
X-MFC after: never
Sponsored by: NLnet Foundation, The FreeBSD Foundation
by running the tunable_mbinit() SYSINIT at SI_ORDER_MIDDLE
before the init_maxsockets() SYSINT at SI_ORDER_ANY.
Reviewed by: rwatson, zec
Sponsored by: The FreeBSD Foundation
MFC after: 4 weeks
The /dev/console device node logs all strings that are written to it.
When the string does not contain a trailing newline, it appends one. I
can imagine this was useful a long time ago, but with our current
rc-scripts, it generates a whole bunch of messages that look like:
| Configuring syscons:
| blanktime
| .
By not appending the newlines, the output of `dmesg -a' is now (almost?)
exactly the same as what the user will see on the console device
(syscons, uart).
aio code and are registered via the recently added SYSCALL32_*() helpers.
- Since the aio code likes to invoke fuword and suword a lot down in the
"bowels" of system calls, add a structure holding a set of operations for
things like storing errors, copying in the aiocb structure, storing
status, etc. The 32-bit system calls use a separate operations vector to
handle fuword32 vs fuword, etc. Also, the oldsigevent handling is now
done by having seperate operation vectors with different aiocb copyin
routines.
- Split out kern_foo() functions for the various AIO system calls so the
32-bit front ends can manage things like copying in and converting
timespec structures, etc.
- For both the native and 32-bit aio_suspend() and lio_listio() calls,
just use copyin() to read the array of aiocb pointers instead of using
a for loop that iterated over fuword/fuword32. The error handling in
the old case was incomplete (lio_listio() just ignored any aiocb's that
it got an EFAULT trying to read rather than reporting an error), and
possibly slower.
MFC after: 1 month
causes data corruption in combination with certain bridges.
Information about this problem was kindly provided by davidch. [1]
- As BGE_FLAG_PCIX is meant to indicate that the controller is in
PCI-X mode, revert to the pre __FreeBSD_version 602101 method of
reading the bus mode register rather than checking the mere
existence of a PCI-X capability, which is also there when the
NIC f.e. is put into a 32-bit slot causing it not to be in PCI-X
mode. Setting BGE_FLAG_PCIX inappropriately could cause the NIC
to be tuned incorrectly.
PR: 128833 [1]
Reviewed by: jhb
MFC after: 3 days
When VLAN tagged frame is received the hardware sets 'LONG' bit of
Rx status word. It is always set when the size of received frame
exceeded 1518 bytes, including CRC. This VLAN tagged frame clears
'OK' bit of Rx status word such that driver should not rely on 'OK'
bit of Rx status word to pass the VLAN tagged frame to upper stack.
To fix the bug, don't use SIS_CMDSTS_PKT_OK for Rx error check and
introduce SIS_RXSTAT_ERROR macro that checks Rx errors. If we are
configured to accept VLAN tagged frames and the received frame size
is less than or equal to maximum allowed length of VLAN tagged
frame, clear 'LONG' bit of Rx status word before checking Rx
errors.
Reported by: Vladimir Ermako < samflanker <> gmail DOT com >
Tested by: Vladimir Ermako < samflanker <> gmail DOT com >
to read-locking in the TCP input path, allowing greater TCP
input parallelism where multiple ithreads or ithread and netisr
are able to run in parallel. Previously, most TCP input paths
held a write lock on the global tcbinfo lock, effectively
serializing TCP input.
Before looking up the connection, acquire a write lock if a
potentially state-changing flag is set on the TCP segment header
(FIN, RST, SYN), and otherwise a read lock. We may later have
to upgrade to a write lock in certain cases (ACKs received by the
syncache or during TIMEWAIT) in order to support global state
transitions, but this is never required for steady-state packets.
Upgrading from a write lock to a read lock must be done as a
trylock operation to avoid deadlocks, and actually violates the
lock order as the tcbinfo lock preceeds the inpcb lock held at
the time of upgrade. If the trylock fails, we bump the refcount
on the inpcb, drop both locks, and re-acquire in-order. If
another thread has freed the connection while the locks are
dropped, we free the inpcb and repeat the lookup (this should
hardly ever or never happen in practice).
For now, maintain a number of new counters measuring how many
times various cases execute, and in particular whether various
optimistic assumptions about when read locks can be used, whether
upgrades are done using the fast path, and whether connections
close in practice in the above-described race, actually occur.
MFC after: 6 weeks
Discussed with: kmacy
Reviewed by: bz, gnn, kmacy
Tested by: kmacy
incremented using in_pcbref(), and decremented using in_pcbfree()
or inpcbrele(). Protocols using only current in_pcballoc() and
in_pcbfree() calls will see the same semantics, but it is now
possible for TCP to call in_pcbref() and in_pcbrele() to prevent
an inpcb from being freed when both tcbinfo and per-inpcb locks
are released. This makes it possible to safely transition from
holding only the inpcb lock to both tcbinfo and inpcb lock
without re-looking up a connection in the input path, timer
path, etc.
Notice that in_pcbrele() does not unlock the connection after
decrementing the refcount, if the connection remains, so that
the caller can continue to use it; in_pcbrele() returns a flag
indicating whether or not the inpcb pointer is still valid, and
in_pcbfee() is now a simple wrapper around in_pcbrele().
MFC after: 1 month
Discussed with: bz, kmacy
Reviewed by: bz, gnn, kmacy
Tested by: kmacy
message for r185765.
Noted by: rdivacky
Requested by: des
Commit message for r185765 should be:
In procfs map handler, and in linprocfs maps handler, do not call
vn_fullpath() while having vm map locked. This is done in anticipation
of the vop_vptocnp commit, that would make vn_fullpath sometime
acquire vnode lock.
Also, in linprocfs, maps handler already acquires vnode lock.
No objections from: des
MFC after: 2 week
sbuf instead of doing uiomove. This allows for reads from non-zero
offsets to work.
Patch is forward-ported des@' one, and was adopted to current code
by dchagin@ and me.
Reviewed by: des (linprocfs part)
PR: kern/101453
MFC after: 1 week
does final drop of the the dq reference to put it onto the free list.
There is a possibility that the dq would be found by another thread
after sync and before the dqh lock is acquired. If that other thread
drops the dq before we have taken the dqh lock, the dirty dq is put on
the free list.
Recheck the DQ_MOD after the dqh lock is relocked. Repeat dqsync() if
the dq is dirty. This ensures that up to date dq is written in the quota
file and fixes assertion in dqget().
Reported and tested by: Frode Nordahl <frode nordahl net>
MFC after: 3 days
Waiting for 1ms for each GMII register access looks overkill and it
may also decrease overall performance of driver because re(4)
invokes mii_tick for every hz.
Tested by: rpaulo
laptops. This includes battery presence detection, charging status, current
and voltage readouts, and charge level indication. The sysctl interface
is somewhat ACPI-like.
established a valid link or not. In miibus_statchg handler add a
check for established link is valid one for the controller(e.g.
1000baseT is not a valid link for fastethernet controllers.)
o Added a flag RE_FLAG_FASTETHER to mark fastethernet controllers.
o Added additional check to know whether we've really encountered
watchdog timeouts or missed Tx completion interrupts. This change
may help to track down the cause of watchdog timeouts.
o In interrupt handler, removed a check for link state change
interrupt. Not all controllers have the bit and re(4) did not
rely on the event for a long time. In addition, re(4) didn't
request the interrupt in RL_IMR register.
Tested by: rpaulo
drivers, there should be a 1us delay after every write when
bit-banging the MII. Also insert barriers in order to ensure
the intended ordering. These changes hopefully will solve the
bus wedging occasionally experienced with DM9102A since r182461.
- Deobfuscate dc_mii_readreg() a bit.
loader_conf_files="foo bar baz"
should cause loading the files listed, and then resume with the
remaining config files (from previous values of the variable).
Unfortunately, sometimes the line was ignored -- actually even
modifying the line in /boot/default/loader.conf sometimes doesn't work.
ANALYSIS: After much investigation, turned out to be a bug in the logic.
The existing code detected a new assignment by looking at the address
of the the variable containing the string. This only worked by pure
chance, i.e. if the new string is longer than the previous value
then the memory allocator may return a different address
to store the string hence triggering the detection.
SOLUTION: This commit contains a minimal change to fix the problem,
without altering too much the existing structure of the code.
However, as a step towards improving the quality and reliability of
this code, I have introduced a handful of one-line functions
(strget, strset, strfree, string= ) that could be used in dozens
of places in the existing code.
HOWEVER:
There is a much bigger problem here. Even though I am no Forth
expert (as most fellow src committers) I can tell that much of the
forth code (in support.4th at least) is in severe need of a
review/refactoring:
+ pieces of code are replicated multiple times instead of writing
functions (see e.g. set_module_*);
+ a lot of stale code (e.g. "structure" definitions for
preloaded_files, kernel_module, pnp stuff) which is not used
or at least belongs elsewhere.
The code bload is extremely bad as the loader runs with very small
memory constraints, and we already hit the limit once (see
http://svn.freebsd.org/viewvc/base?view=revision&revision=185132
Reducing the footprint of the forth files is critical.
+ two different styles of coding, one using pure stack functions
(maybe beautiful but surely highly unreadable), one using
high level mechanisms to give names to arguments and local
variables (which leads to readable code).
Note that this code is used by default by all FreeBSD installations,
so the fragility and the code bloat are extremely damaging.
I will try to work fixing the three items above, but if others have
time, please have a look at these issues.
MFC after: 4 weeks
multiple algorithms and potentially collect multiple samples.
Instead of a single calibration interval we now have short and long
intervals; the long interval roughly corresponds to the previous
single interval. The short interval is used to speedup collection
of samples and happens much quicker. We make calls using the short
interval until we're told the calibration work is complete at which
point we fallback to the long interval. In addition there is a
much longer reset interval used to flush all calibration state and
cause everthing to start anew.
With these changes you can also disable calibration entirely by
setting the long interval to zero.
at. I don't think this will make a huge difference, but I have
received a report of a interrupt storm on one 16-bit card that this
might fix (chances are it won't, since I think that we may need to
check both the CBB registers for the 16-bit card as well as the PCIC
registers for power state change).
Submitted by: jhb@
the power interrupt and init code waiting for the interrupt are
running on different CPUs. I haven't seen this make any real
difference, but I've also had some reports of odd behavior I can't
otherwise explain. It is an infrequent operation, and certainly
wouldn't hurt.
my right mouse button and keyboard LEDs from working due to mangled
configuration packets. Fixed several other races and associated problems in the
main ADB stack that were exposed while fixing this.
Now it is possible to suspend/resume with inserted and active card.
To reinitialize card on resume and to detect card change while suspended,
implement bus rescan routines. It can also be used by controllers without
card presence detection signals or with multiple cards per slot support.
While there, cleanup msleep() usage. We have no any rights to exit without
"request done" signal from driver as it could lead to modify after free.
RTFREE_LOCKED() here. This macro makes sure the reference count
on the route is being managed properly. This elimates another
case which results in the following message being printed to the
console:
rtfree: 0xc841ee88 has 1 refs
Reviewed by: bz
MFC after: 2 weeks
bit of debugging afterwards):
- Fix protection code for notification generation.
- Decouple associd from vtag
- Allow vtags to have less strigent requirements in non-uniqueness.
o don't pre-hash them when you issue one in a cookie.
o Allow duplicates and use addresses and ports to
discriminate amongst the duplicates during lookup.
- Add support for the NAT draft draft-ietf-behave-sctpnat-00, this
is still experimental and needs more extensive testing with the
Jason Butt ipfw changes.
- Support for the SENDER_DRY event to get DTLS in OpenSSL working
with a set of patches from Michael Tuexen (hopefully heading to OpenSSL soon).
- Update the support of SCTP-AUTH by Peter Lei.
- Use macros for refcounting.
- Fix MTU for UDP encapsulation.
- Fix reporting back of unsent data.
- Update assoc send counter handling to be consistent with endpoint sent counter.
- Fix a bug in PR-SCTP.
- Fix so we only send another FWD-TSN when a SACK arrives IF and only
if the adv-peer-ack point progressed. However we still make sure
a timer is running if we do have an adv_peer_ack point.
- Fix PR-SCTP bug where chunks were retransmitted if they are sent
unreliable but not abandoned yet.
With the help of: Michael Teuxen and Peter Lei :-)
MFC after: 4 weeks
an unclean shutdown would make it impossible to mount rootfs at boot.
PR: kern/128529
Reviewed by: pjd
Approved by: rwatson (mentor)
Sponsored by: FreeBSD Foundation
do not need any locking. Opening and closing translators is serialized
using an sx lock.
Note: This depends on the earlier fix to kern_module.c to properly order
MOD_UNLOAD events.
MFC after: 2 months
memory barriers on i386. It works as a serialization instruction on
all IA32 CPUs.
Alternative solution of using {s,l,}fence requires run-time checking
of the presense of the corresponding SSE or SSE2 extensions, and
possible boot-time patching of the kernel text.
Suggested by: many
parent threads sleep on the parent' struct proc until corresponding
child releases the vmspace. Each sleep is interlocked with proc mutex of
the child, that triggers assertion in the sleepq_add(). The assertion
requires that at any time, all simultaneous sleepers for the channel use
the same interlock.
Silent the assertion by using conditional variable allocated in the
child. Broadcast the variable event on exec() and exit().
Since struct proc * sleep wait channel is overloaded for several
unrelated events, I was unable to remove wakeups from the places where
cv_broadcast() is added, except exec().
Reported and tested by: ganbold
Suggested and reviewed by: jhb
MFC after: 2 week
move that module to the head of the associated linker file's list of modules.
The end result is that once all the modules are loaded, they are sorted in
the reverse of their load order. This causes the kernel linker to invoke
the MOD_QUIESCE and MOD_UNLOAD events in the reverse of the order that
MOD_LOAD was invoked. This means that the ordering of MOD_LOAD events that
is set by the SI_* paramters to DECLARE_MODULE() are now honored in the same
order they would be for SYSUNINIT() for the MOD_QUIESCE and MOD_UNLOAD
events.
MFC after: 1 month
unloading any modules. As a result, if any module veto's an unload
request via MOD_QUIESCE, the entire set of modules for that linker
file will remain loaded and active now rather than leaving the kld
in a weird state where some modules are loaded and some are unloaded.
- This also moves the logic for handling the "forced" unload flag out of
kern_module.c and into kern_linker.c which is a bit cleaner.
- Add a module_name() routine that returns the name of a module and use that
instead of printing pointer values in debug messages when a module fails
MOD_QUIESCE or MOD_UNLOAD.
MFC after: 1 month
interrupt code to be more robust. I've been running these changes for
over a year... With these changes, I don't see the ath card going
into reset like the code in the tree.
packet loss, of between 10-30%. The fix is to put the PHY into
and take it out of local loopback mode when resetting the interface.
Obtained from: Chelsio Inc.
MFC after: 3 days
o Chip full mask revision 2 or later controllers have to
set correct Tx MAC and Tx offload clock depending on negotiated
link speed.
o JMC260 chip full mask revision 2 has a silicon bug that can't
handle 64bit DMA addressing. Add workaround to the bug by
limiting DMA address space to be within 32bit.
o Valid FIFO space of receive control and status register was
changed on chip full mask revision 2 or later controllers. For
these controllers, use default 16QW as it's supposed to be the
safest value for maximum PCIe compatibility. JMicron confirmed
performance will not be reduced even if the FIFO space is set
to 16QW.
o When interface is put into suspend/shutdown state, remove Tx MAC
and Tx offload clock to save more power. We don't need Tx clock
at all in this state.
o Added new register definition for chip full mask revision 2 or
later controllers.
Thanks to JMicron for their continuous support of FreeBSD.
change. As a side effect, this makes the excessive interrupts to
disappear which has been observed as a regression in recent stable/7.
Reported by: many (on -stable@)
Reviewed by: davidch
validation code on ZFS.
Problem: when opening file with O_CREAT|O_EXCL NFS has to jump through
extra hoops to ensure O_EXCL semantics. Namely, client supplies of 8
bytes (NFSX_V3CREATEVERF) bytes of verification data to uniquely
identify this create request. Server then creates a new file with access
mode 0, copies received 8 bytes into va_atime member of struct vattr and
attempt to set the atime on file using VOP_SETATTR. If that succeeds, it
fetches file attributes with VOP_GETATTR and verifies that atime
timestamps match. If timestamps do not match, NFS server concludes it
has probbaly lost the race to another process creating the file with the
same name and bails with EEXIST.
This scheme works OK when exported FS is FFS, but if underlying
filesystem is ZFS _and_ server is running 64bit kernel, it breaks down
due to sanity checking in zfs_setattr function, which refuses to accept
any timestamps which have tv_sec that cannot be represented as 32bit
int. Since struct timespec fields are 64 bit integers on 64bit platforms
and server just copies NFSX_V3CREATEVERF bytes info va_atime, all eight
bytes supplied by client end up in va_atime.tv_sec, forcing it out of
valid 32bit range.
The solution this change implements is simple: it treats
NFSX_V3CREATEVERF as two 32bit integers and unpacks them separately into
va_atime.tv_sec and va_atime.tv_nsec respectively, thus guaranteeing
that tv_sec remains in 32 bit range and ZFS remains happy.
Reviewed by: kib
Close subtle but relatively unlikely race conditions when
propagating the vnode write error to other active sessions
tracing to the same vnode, without holding a reference on
the vnode anymore. [2]
PR: kern/126368 [1]
Submitted by: rwatson [2]
Reviewed by: kib, rwatson
MFC after: 4 weeks
boot0.S changes:
+ import a patch from Christoph Mallon to rearrange the various
print functions and save another couple of bytes;
+ implement the suggestion in PR 70531 to enable booting from
any valid partition because even the extended partitions that
were previously in our kill list may contain a valid boot loader.
This simplifies the code and saves some bytes;
+ followwing up PR 127764, implement conditional code to preserve
the 'Volume ID' which might be used by other OS (NT, XP, Vista)
and is located at offset 0x1b8. This requires a relocation of the
parameter block within the boot sector -- there is no other
possible workaround.
To address this, boot0cfg has been updated to handle both
versions of the boot code;
+ slightly rearrange the strings printed in the menus to make
the code buildable with all options. Given the tight memory
budget, this means that with certain options we need to
shrink or remove certain labels.
and especially:
make -DVOLUME_LABEL -DPXE the default options.
This means that the newly built boot0 block will preserve the
Volume ID, and has the (hidden) option F6 to boot from INT18/PXE.
I think the extra functionality is well worth the change.
The most visible difference here is that the 'Default: ' string
now becomes 'Boot: ' (it can be reverted to the old value
but then we need to nuke 1/2 partition name or entries to
make up for the extra room).
boot0cfg changes:
+ modify the code to recognise the new boot0 structure (with the
relocated options block to make room for the Volume id).
+ add two options, '-i xxxx-xxxx' to set the volume ID, -e c
to modify the character printed in case of bad input
PR: 127764 70531
Submitted by: Christoph Mallon (portions)
MFC after: 4 weeks
contrib/openbsm (svn merge) and sys/{bsm,security/audit} (manual merge).
- Add OpenBSM contrib tree to include paths for audit(8) and auditd(8).
- Merge support for new tokens, fixes to existing token generation to
audit_bsm_token.c.
- Synchronize bsm includes and definitions.
OpenBSM history for imported revisions below for reference.
MFC after: 1 month
Sponsored by: Apple Inc.
Obtained from: TrustedBSD Project
--
OpenBSM 1.1 alpha 2
- Include files in OpenBSM are now broken out into two parts: library builds
required solely for user space, and system includes, which may also be
required for use in the kernels of systems integrating OpenBSM. Submitted
by Stacey Son.
- Configure option --with-native-includes allows forcing the use of native
include for system includes, rather than the versions bundled with OpenBSM.
This is intended specifically for platforms that ship OpenBSM, have adapted
versions of the system includes in a kernel source tree, and will use the
OpenBSM build infrastructure with an unmodified OpenBSM distribution,
allowing the customized system includes to be used with the OpenBSM build.
Submitted by Stacey Son.
- Various strcpy()'s/strcat()'s have been changed to strlcpy()'s/strlcat()'s
or asprintf(). Added compat/strlcpy.h for Linux.
- Remove compatibility defines for old Darwin token constant names; now only
BSM token names are provided and used.
- Add support for extended header tokens, which contain space for information
on the host generating the record.
- Add support for setting extended host information in the kernel, which is
used for setting host information in extended header tokens. The
audit_control file now supports a "host" parameter which can be used by
auditd to set the information; if not present, the kernel parameters won't
be set and auditd uses unextended headers for records that it generates.
OpenBSM 1.1 alpha 1
- Add option to auditreduce(1) which allows users to invert sense of
matching, such that BSM records that do not match, are selected.
- Fix bug in audit_write() where we commit an incomplete record in the
event there is an error writing the subject token. This was submitted
by Diego Giagio.
- Build support for Mac OS X 10.5.1 submitted by Eric Hall.
- Fix a bug which resulted in host XML attributes not being arguments so
that const strings can be passed as arguments to tokens. This patch was
submitted by Xin LI.
- Modify the -m option so users can select more then one audit event.
- For Mac OS X, added Mach IPC support for audit trigger messages.
- Fixed a bug in getacna() which resulted in a locking problem on Mac OS X.
- Added LOG_PERROR flag to openlog when -d option is used with auditd.
- AUE events added for Mac OS X Leopard system calls.
directly include only the header files needed. This reduces the
unneeded spamming of various headers into lots of files.
For now, this leaves us with very few modules including vnet.h
and thus needing to depend on opt_route.h.
Reviewed by: brooks, gnn, des, zec, imp
Sponsored by: The FreeBSD Foundation
Sgtty is a programming interface that has been replaced by termios over
the years. In June we already removed <sgtty.h>, which exposes the
ioctl()'s that are implemented by this interface. The importance of this
flag is overrated right now.
when it sees only received packets. In some cases where a device only
recieves data it mistakenly thinks that its transmitting side is broken
and resets the device.
Obtained from: Chelsio Inc.
MFC after: 3 days
of the boot0.S code, with a number of compile-time selectable options,
the most interesting one being the ability to select PXE booting.
The code is completely compatible with the previous one, and with
the boot0cfg program. Even the actual code is largely unmodified,
with only minor rearrangements or fixes to make room for the new
features.
The behaviour of the standard build differs from the previous
version in the following, minor things:
+ 'noupdate' is the default, which means the code does not
write back the selection to disk. You can enable the feature
at runtime with boot0cfg, or changing the flags in the Makefile.
+ a drive number of 0x00 (floppy, or USB in floppy emulation) is
now accepted as valid. Previously, it was overridden with 0x80,
meaning that the partition table coming from the media was
used to access sectors on a possibly different media.
You can revert to the previous mode building with -DCHECK_DRIVE,
and you can always use the 'setdrv' option in boot0cfg
+ certain FAT or NTFS partitions are listed as WIN instead of DOS.
+ the 'bel' character on a bad selection is replaced by a '#' to
make it clear that the system is not hang even if the machine
does not have a speaker. This can be reverted back at compile
time, or at runtime with an upcoming boot0cfg option.
Additional features are available as compile time options,
and may be become the default if deemed useful. In particular:
+ INT18/PXE boot (make -DPXE)
This option enables booting through INT 18h (which on certain
BIOSes can be hooked to PXE) by pressing F6. There is unfortunately
no room to print the additional menu option.
Also, to make room for the code, the 'Default: ' string is
changed to 'Boot: '
+ print current drive number (make -DTEST)
Prints a line indicating the current drive number.
This is useful to figure out what is going on for machines/bioses
which remap drives in sometimes surprising ways.
+ disable numeric keys in console mode (make -DONLY_F_KEYS)
Not really a significant option, but it is needed to make
room for the -DTEST mode.
+ disable floppy support (make -DCHECK_DRIVE)
Revert to the old behaviour of only accepting 0x80 and above
as valid drive numbers.
MFC after: 6 weeks
entries for one name. Then, creating inode with that name would remove
one entry, leaving others dormant. Reclaiming the vnode would uncover
negative entries, causing false return of ENOENT from the calls like
stat, that do not create inode.
Prevent creation of the duplicated negative entries.
Reported and debugged with: pho
Reviewed by: jhb
X-MFC: after shared lookup changes
hardware for PMCs that have been configured for sampling.
- Bug fix: acknowledge PMC hardware overflows irrespective of the
the (software) PMC's state.
- break complex conditionals in to multiple lines to avoid wrapping
- remove copious unused debug statements
- be more aggressive about cleaning in the calling thread
- eliminate usage of ENOSPC
- increase number of iterations that cxgbsp can do
- eliminate "initerr" usage to simplify ENOBUFS handling
- when coalescing pass all packets to BPF
- always set overrun if hardware queue is full
This changes struct kinfo_filedesc and kinfo_vmentry such that they are
same on both 32 and 64 bit platforms like i386/amd64 and won't require
sysctl wrapping.
Two new OIDs are assigned. The old ones are available under
COMPAT_FREEBSD7 - but it isn't that simple. The superceded interface
was never actually released on 7.x.
The other main change is to pack the data passed to userland via the
sysctl. kf_structsize and kve_structsize are reduced for the copyout.
If you have a process with 100,000+ sockets open, the unpacked records
require a 132MB+ copyout. With packing, it is "only" ~35MB. (Still
seriously unpleasant, but not quite as devastating). A similar problem
exists for the vmentry structure - have lots and lots of shared libraries
and small mmaps and its copyout gets expensive too.
My immediate problem is valgrind. It traditionally achieves this
functionality by parsing procfs output, in a packed format. Secondly, when
tracing 32 bit binaries on amd64 under valgrind, it uses a cross compiled
32 bit binary which ran directly into the differing data structures in 32
vs 64 bit mode. (valgrind uses this to track file descriptor operations
and this therefore affected every single 32 bit binary)
I've added two utility functions to libutil to unpack the structures into
a fixed record length and to make it a little more convenient to use.
offload for VLAN frames are also supported. The VLAN hardware
assistance is available only on 82550/82551 based controllers.
While I'm here change the confusing name of bit1 in byte 22 of
configuration block to vlan_drop_en. The bit controls whether
hardware strips VLAN tagged frame or not. Special thanks to wpaul
who sent valuable VLAN related information to me.
Tested on: i386, sparc64
events. Just reading PMDR register was not enough to have fxp(4)
immuninize against received magic packets during system boot.
Tested by: Alexey Shuvaev < shuvaev <> physik DOT uni-wuerzburg DOT de >
