Add missing support for specifying I/O control flags during core reset,
and resolve a number of siba(4)-specific reset issues:
- Add missing check for target reject flags in siba_is_hw_suspended().
- Remove incorrect wait on SIBA_TMH_BUSY when modifying any target state
register; this should only be done when waiting for initiated
transactions to clear.
- Add missing wait on SIBA_IM_BY when asserting SIBA_IM_RJ.
- Overwrite any previously set SIBA_TML_REJ flag when bringing the core
out of reset. This fixes a lockup that occured when we brought up a core
(after reboot) that had previously been placed into RESET by siba_bwn(4).
Approved by: adrian (mentor, implicit)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D13039
The bwn(4) driver requires a number of extensions to the bhnd(4) PMU
interface to support external configuration of PLLs, LDOs, and other
parameters that require chipset or PHY-specific workarounds.
These changes add support for:
- Writing raw voltage register values to PHY-specific LDO regulator
registers (required by LP-PHY).
- Enabling/disabling PHY-specific LDOs (required by LP-PHY)
- Writing to arbitrary PMU chipctrl registers (required for common PHY PLL
reset support).
- Requesting chipset/PLL-specific spurious signal avoidance modes.
- Querying clock frequency and latency.
Additionally, rather than updating legacy PWRCTL support to conform to the
new PMU interface:
- PWRCTL API is now provided by a bhnd_pwrctl_if.m interface.
- Since PWRCTL is only found in older SSB-based chipsets, translation from
bhnd(4) bus APIs to corresponding PWRCTL operations is now handled
entirely within the siba(4) driver.
- The PWRCTL-specific host bridge clock gating APIs in bhnd_bus_if.m have
been lifted out into a standalone bhnd_pwrctl_hostb_if.m interface.
Approved by: adrian (mentor, implicit)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D12664
On BHND MIPS SoCs, this replaces the use of hard-coded MIPS IRQ#s in the
common bhnd(4) core drivers; we now register an INTRNG child PIC that
handles routing of backplane interrupt vectors via the MIPS core.
On BHND PCI devices, backplane interrupt vectors are now routed to the
PCI/PCIe host bridge core when bus_setup_intr() is called, where they are
dispatched by the PCI core via a host interrupt (e.g. INTx/MSI).
The bhndb(4) bridge driver tracks registered interrupt handlers for the
bridged bhnd(4) devices and manages backplane interrupt routing, while
delegating actual bus interrupt setup/teardown to the parent bus on behalf
of the bridged cores.
Approved by: adrian (mentor, implicit)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D12518
parser.
This allows us to use the EROM parser API in cases where the standard bus
space I/O APIs are unsuitable. In particular, this will allow us to parse
the device enumeration table directly from bhndb(4) drivers, prior to
full attach and configuration of the bridge.
Approved by: adrian (mentor)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D12510
BHND_EROM_DUMP() method.
Dump the EROM tables to the coneole on mips/broadcom devices if bootverbose
is enabled; this functionality is primarily useful when debugging SoC EROM
parsing and device matching issues during early boot.
Reviewed by: mizhka
Approved by: adrian (mentor)
Sponsored by: Plausible Labs
Differential Revision: https://reviews.freebsd.org/D10122
This commit is part of D6920 review. One of macro had wrong prefix:
BMCA => BCMA
Reviewed by: landonf, adrian (mentor)
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D6920
- Added bhnd(4) bus APIs for per-core ioctl/iost register access.
- Updated reset/suspend bhnd(4) APIs for compatibility with ioctl/iost
changes.
- Implemented core reset/suspend support for both bcma(4) and siba(4).
- Implemented explicit release of all outstanding PMU requests at the bus
level when putting a core into reset.
Approved by: adrian (mentor, implicit)
Differential Revision: https://reviews.freebsd.org/D8009
This adds bhnd(4) bus-level support for querying backplane interrupt vector
routing, and delegating machine/bridge-specific interrupt handling to the
concrete bhnd(4) driver implementation.
On bhndb(4) bridged PCI devices, we provide the PCI/MSI interrupt directly
to attached cores.
On MIPS devices, we report a backplane interrupt count of 0, effectively
disabling the bus-level interrupt assignment. This allows mips/broadcom
to temporarily continue using hard-coded MIPS IRQs until bhnd_mips PIC
support is implemented.
Reviewed by: mizhka
Approved by: adrian (mentor, implicit)
Adds support for probing and initializing bhndb(4) bridge state using
the bhnd_erom API, ensuring that full bridge configuration is available
*prior* to actually attaching and enumerating the bhnd(4) child device,
allowing us to safely allocate bus-level agent/device resources during
bhnd(4) bus enumeration.
- Add a bhnd_erom_probe() method usable by bhndb(4). This is an analogue
to the existing bhnd_erom_probe_static() method, and allows the bhndb
bridge to discover the best available erom parser class prior to newbus
probing of its children.
- Add support for supplying identification hints when probing erom
devices. This is required on early EXTIF-only chipsets, where chip
identification registers are not available.
- Migrate bhndb over to the new bhnd_erom API, using bhnd_core_info
records rather than bridged bhnd(4) device_t references to determine
the bridged chipsets' capability/bridge configuration.
- The bhndb parent (e.g. if_bwn) is now required to supply a hardware
priority table to the bridge. The default table is currently sufficient
for our supported devices.
- Drop the two-pass attach approach we used for compatibility with bhndb(4) in
the bhnd(4) bus drivers, and instead perform bus enumeration immediately,
and allocate bridged per-child bus-level resources during that enumeration.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7768
This defines a new bhnd_erom_if API, providing a common interface to device
enumeration on siba(4) and bcma(4) devices, for use both in the bhndb bridge
and SoC early boot contexts, and migrates mips/broadcom over to the new API.
This also replaces the previous adhoc device enumeration support implemented
for mips/broadcom.
Migration of bhndb to the new API will be implemented in a follow-up commit.
- Defined new bhnd_erom_if interface for bhnd(4) device enumeration, along
with bcma(4) and siba(4)-specific implementations.
- Fixed a minor bug in bhndb that logged an error when we attempted to map the
full siba(4) bus space (18000000-17FFFFFF) in the siba EROM parser.
- Reverted use of the resource's start address as the ChipCommon enum_addr in
bhnd_read_chipid(). When called from bhndb, this address is found within the
host address space, resulting in an invalid bridged enum_addr.
- Added support for falling back on standard bus_activate_resource() in
bhnd_bus_generic_activate_resource(), enabling allocation of the bhnd_erom's
bhnd_resource directly from a nexus-attached bhnd(4) device.
- Removed BHND_BUS_GET_CORE_TABLE(); it has been replaced by the erom API.
- Added support for statically initializing bhnd_erom instances, for use prior
to malloc availability. The statically allocated buffer size is verified both
at runtime, and via a compile-time assertion (see BHND_EROM_STATIC_BYTES).
- bhnd_erom classes are registered within a module via a linker set, allowing
mips/broadcom to probe available EROM parser instances without creating a
strong reference to bcma/siba-specific symbols.
- Migrated mips/broadcom to bhnd_erom_if, replacing the previous MIPS-specific
device enumeration implementation.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7748
This will allow us to perform bhndb(4) bridge configuration based on
the identified hardware, prior to performing full enumeration of the
child bhnd bus.
Approved by: adrian (mentor, implicit)
- Added bhnd_pmu driver implementations for PMU and PWRCTL chipsets,
derived from Broadcom's ISC-licensed HND code.
- Added bhnd bus-level support for routing per-core clock and resource
power requests to the PMU device.
- Lift ChipCommon support out into the bhnd module, dropping
bhnd_chipc.
Reviewed by: mizhka
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7492
This adds support for performing platform_reset() on all supported
devices, using early boot enumeration of chipc capabilities and
available cores.
- Added Broadcom-specific MIPS CP0 register definitions used by
BCM4785-specific reset handling.
- Added a bcm_platform structure for tracking chipc/pmu/cfe platform
data.
- Extended the BCMA EROM API to support early boot lookup of core info
(including port/region mappings).
- Extended platform_reset() to support PMU, PMU+AOB, and non-PMU
devices.
Reviewed by: mizhka
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7539
pci_if.
This allows bhnd(4) to manage per-device state (such as per-core
pmu/clock refcounting) on behalf of subclass driver instances.
Approved by: re (gjb), adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D6959
This patch addes missing implementation of BHND_BUS_RESET_CORE function for BCMA.
The reset procedure is very simple: enable reset mode, stop clocking,
enable clocking & force clock gating, disable reset mode, stop clock gating.
Tested:
* (michael) Tested on ASUS RT-N53 for enabling/reset USB core
Submitted by: Michael Zhilin <mizhka@gmail.com>
Approved by: re (gjb)
Changes:
- Fixed incorrect MIPS74k vendor ID in the bhnd core descriptor tables
- Fixed MIPS core driver's matching against MIPS/MIPS33 cores.
- Improved MIPS3302 core description.
- Enabled BUS_PASS_BUS on the bhnd nexus drivers to allow early probing
of the MIPS core.
- Enabled BUS_PASS_CPU on the MIPS core driver to ensure correct attach
order.
- Disabled matching of the MIPS core driver on non-SoC devices.
Reviewed by: Michael Zhilin <mizhka@gmail.com>
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D6735
Now that bhnd(4) provides feature parity with the previous siba/mips
implementation, we can switch sentry5 over and begin lifting common
support code out for use across bhnd(4) embedded targets.
Changes:
- Fixed enumeration of siba(4) per-core address maps, required for
discovery of memory mapped chipc flash region on siba(4) devices.
- Simplified bhnd kernel configuration (dropped 'bhndbus' option).
- Replaced files.broadcom's direct file references with their
corresponding standard kernel options.
- Lifted out common bcma/siba nexus support, inheriting from the new
generic bhnd_nexus driver.
- Dropped now-unused sentry5 siba code.
- Re-integrated BCM into the universe build now that it actually compiles.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D6712
This adds a BHND_BUS_GET_ATTACH_TYPE(); the primary use-case is to let
chipc make a coarse-grained determination as to whether UART, SPI, etc
drivers ought to be attached, and on fullmac devices, whether a real
CPU driver ought to be skipped for the ARM core, etc.
Tested:
* BCM4331 (BHND)
* BCM4312 (SIBA)
Submitted by: Landon Fuller <landonf@landonf.org>
Differential Revision: https://reviews.freebsd.org/D6492
This patch introduces support of BHND on SoC: nexus-to-bhnd drivers.
bhnd_soc is attached under nexus and responsible for all BHND-style calls
from bhnd(4) bus to parents.
bcma_nexus is bhnd(4) bus, attached to bhnd_soc and implement all
nexus-style behaviour of BHND.
Submitted by: Michael Zhilin <mizhka@gmail.com>
Reviewed by: Landon Fuller <landonf@landonf.org>
Differential Revision: https://reviews.freebsd.org/D6248
Centralizes fetching of board information (vendor, type, revision, etc),
and adds support for matching quirks against board identification info.
* Adds a BHND_BUS_READ_BOARD_INFO(), allowing bhnd bus/bus parent(s) to
handle implementation-specific fetching of board info.
* Integrates board type constants from the latest Broadcom ISC-licensed
bcmdevs.h included in dd-wrt's Broadcom driver source drops.
* Adds support for matching on chip/board quirks to bhnd_device_quirks()/
bhnd_chip_quirks().
* Use the new board/chip quirk matching to match Apple devices that failed
to set BFL2_PCIEWAR_OVR in SROM.
Submitted by: Landon Fuller <landonf@landonf.org>
Differential Revision: https://reviews.freebsd.org/D6361
* bcma.c - assign different resource IDs for different regions
* bcma_erom.c - workaround for BCM/MIPS bus enumerations
Tested:
* (submitter) Tested on ASUS RT-N16 initially, double checked on ASUS RT-N53
* (landonf) BCM4331
Submitted by: Michael Zhilin <mizkha@gmail.com>
Differential Revision: https://reviews.freebsd.org/D6245
This allows bus children to query for the host bridge device, rather
than having to iterate over all attached devices.
Submitted by: Landon Fuller <landonf@landonf.org>
Differential Revision: https://reviews.freebsd.org/D6193
Further to r299119. GCC architectures failed with
bcma_subr.c:138: warning: control reaches end of non-void function
Sponsored by: The FreeBSD Foundation
SoCs and various chips (including, famously, their wifi chips.)
This is "just" (all 20,000 lines of it) code to enumerate the various
versions of busses inside these devices, including the PCI bridge and
the direct SIBA bridge found in MIPS chips.
It also includes shared code for some bus operations (suspend, resume, etc);
EEPROM/SROM/etc parsing and other things that are shared between chips.
Eventually this'll replace the code that bwi/bwn uses for the internal
bus, as well as some apparently upcoming mips74k broadcom SoC support
which uses bwn!
Thanks to Landon Fuller <landonf@landonf.org> for all this work!
Obtained from: https://github.com/landonf/freebsd/compare/user/landonf/bcm4331-CURRENT
