based devices (QUALCOMMINC 0x2000). He made it use SCSI eject instead of
ZTE STOR eject. This prevented my ZTE MF626 dongle from switching.
- Apply both eject methods for ZTE STOR based devices. Works on my as
well as mav's device.
- Remove the duplicate.
- Sort the usbdevs entries for Qualcomm so this won't happen again.
- Add bootverbose message displaying the fact that we are ejecting (and
how).
Reviewed by: mav
MFC after: 2 weeks
information through devd. My E220 now produces the notification (1 line):
+u3g0 at bus=1 hubaddr=1 port=0 devaddr=2 interface=0 \
vendor=0x12d1 product=0x1003 devclass=0x00 devsubclass=0x00 \
sernum="" release=0x0000 intclass=0xff intsubclass=0xff \
ttyname=U0 ttyports=2 on uhub0
Note: serial/ufoma and net/uhso still provide port number and tty name
(uhso only) information through sysctls, which should now be removed.
Reviewed by: hpselasky
- Fix the loop count on detach (causing a panic on detaching a serial
dongle).
- Increase a buffer in case some driver want extra long tty device names
(postfixing the purpose of the tty for example, e.g. u3g.ppp).
- hw.usb.ucom.cons_unit is now split into
hw.usb.ucom.cons_unit/...cons_subunit.
Note: The tunable/sysctl hw.usb.ucom.cons_unit needs to be reviewed if
a) a console was defined a USB serial devices, and a USB device with
more than 1 subunit is present, and this device is attached before the
device functioning as a console
or
b) a console was defined on a USB device with more than 1 subunit
Reviewed by: hps
MFC after: 2 weeks
special eject command to reappear as modem. It also requires DIR_IN flag
in the command message, so we supply some dummy data along with the command.
Feedback from X080S owners appreciated. I have not a pure Alcatel/TCTMobile
device, but another one under "Svyaznoy" (Связной) brand, and I didn't yet
managed to get it working. It is successfully recognized, it responds to
AT commands, but it shuts up right after successfull CONNECT response.
Reviewed by: hps
list of devices supported by uplcom(4) with the following sources:
NetBSD src/sys/dev/usb/uplcom.c 1.70
OpenBSD src/sys/dev/usb/uplcom.c 1.52
Linux drivers/usb/serial/pl2303.h from kernel 2.6.35
BeOS usb_serial/driver.c 1.32
Give several devices better descriptions, and rename
PROLIFIC2 -> NETINDEX while here to match everybody else.
MFC after: 6 weeks (after r211111)
within the device table. This code uses the same algorithm as used in the
Linux, NetBSD and DragonflyBSD driver.
While investigating this, it became apparent that the Linux driver always
initialises the device, and not just in the PL2303HX case. Change
uplcom(4) to do the same.
This change allows us to synchronize our device ID list with Linux and
NetBSD, without requiring knowledge of the chipset in use.
Reviewed by: hselasky
MFC after: 6 weeks
and BeOS. The devices supported by uslcom(4) are now in sync with:
NetBSD src/sys/dev/usb/uslsa.c 1.11
OpenBSD src/sys/dev/usb/uslcom.c 1.20
Linux source/drivers/usb/serial/cp210x.c from kernel 2.6.35
BeOS usb_serial/driver.c 1.32
Two vendor/product IDs from Linux have not been added to uslcom(4):
SILABS SAEL - This device has special code in u3g to support it
SILABS GSM2228 - I suspect this should also be covered by u3g(4).
MFC after: 1 week
This patch is different to that provided in the PR, due to the changes in
this driver since 7.x.
PR: usb/129945
Submitted by: Antonio Hilario <avahilario gmail.com>
MFC after: 1 week
- Bring in several other devices from OpenBSD while here. Use the
official manufacturer name over the OpenBSD name in the case of
GEMALTO. Reorder list slightly to aid future syncing.
- Remove duplicate SILABS CP2102 define from usbdevs
PR: usb/131912 [1]
Submitted by: Jack Twilley <mathuin gmail.com> [1]
MFC after: 1 week
is issued at the beginning of the initial IN/OUT data transfers. Reason
unknown, probably firmware fault. Now the stall is only cleared on data
transfer errors.
PR: usb/144199
Submitted by: Hans Petter Selasky
command in the usb_msctest routines, as well as a general tidyup.
This now properly ejects the ZTE MF636, Option Gi0322 and Novatel MC950D
devices I have on my desk.
perform a function such as ejecting a 3G autoinstaller disk. The eventhandler
system properly tracks threads and is safe to unload, remove the
setting/clearing of a function pointer in the kernel by u3g(4) which included a
tsleep for safety.
management over the data endpoint causes communication to die.
Take this one step further and model it on the existing NetBSD quirk and import
other device IDs from them.
Obtained from: NetBSD
