state lower than the lowest one supported by the current CPU. This closes
some races with changes to the hw.acpi.cpu_cx_lowest sysctl while Cx
states for individual CPUs were changing (e.g. unplugging the AC adapter
of a laptop) that could result in panics.
Submitted by: Giovanni Trematerra
Tested by: David Demelier demelier dot david of gmail
MFC after: 3 days
via %s
Most of the cases looked harmless, but this is done for the sake of
correctness. In one case it even allowed to drop an intermediate buffer.
Found by: clang
MFC after: 2 week
device, make sure we have no real HPET device entry with same ID.
As side effect, it potentially allows several HPETs to be attached.
Use first of them for timecounting, rest (if ever present) could later
be used as event sources.
Setting the new sysctl MIB "debug.acpi.enable_debug_objects" to a non-zero
value enables us to print Debug object when something is written to it.
- Allow users to disable interpreter slack mode. Setting the new tunable
"debug.acpi.interpreter_slack" to zero disables some workarounds for common
BIOS mistakes and enables strict ACPI implementations by the specification.
It is belived that that pass s not needed anymore.
Specifically it is not required now for the reasons that were given
in the removed comment.
Discussed with: jhb
MFC after: 4 weeks
Some current systems dynamically load SSDT(s) when _PDC/_OSC method
of Processor is evaluated. Other devices in ACPI namespace may access
objects defined in the dynamic SSDT. Drivers for such devices might
have to have a rather high priority, because of other dependencies.
Good example is acpi_ec driver for EC.
Thus we attach to Processors as early as possible to load the SSDTs
before any other drivers may try to evaluate control methods.
It also seems to be a natural order for a processor in a device
hierarchy.
On the other hand, some child devices on acpi cpu bus need to access
other system resources like PCI configuration space of chipset devices,
so they need to be probed and attached rather late.
For this reason we probe and attach the cpu bus at
SI_SUB_CONFIGURE:SI_ORDER_MIDDLE SYSINIT level.
In the future this could be done more elegantly via multipass.
Please note that acpi drivers that might access ACPI namespace from
device_identify will do that before _PDC/_OSC of Processors are evaluated.
Legacy cpu driver is not affected by this change.
PR: kern/142561 (in part)
Reviewed by: jhb
Silence from: acpi@
MFC after: 5 weeks
_PDC was deprecated in favor of _OSC long time ago, but it
seems that they still peacefully coexist and in some case
only _PDC is present.
Still _OSC provides a reacher interface and is capable to
report back its status.
If the status is non-zero, then report it, we may find
it useful to understand what firmware expects from OS.
Also clean up some comments that became less useful over time.
Reviewed by: njl, jhb, rpaulo
MFC after: 3 weeks
Also, account for a quirk of AMD/ATI HPET which reports number of timers
instead of id of the last timer as manadated by the specification.
Currently this has no effect on functionality but in the future we may
make actual use of the HPET timers, not only of its timecounter.
MFC after: 2 weeks
This is not only a prudent thing to do, but also makes sure that probe
method is not confused by non-NULL 'private', if the previous attach
attempt fails for any reason.
PR: kern/142561
Tested by: Alex Goncharov <alex-goncharov@comcast.net>
MFC after: 4 days
o acpi_hpet: auto-added 'wildcard' devices can be identified by
non-NULL handle attribute.
o acpi_ec: auto-add 'wildcard' devices can be identified by
unset (NULL) private attribute.
o acpi_cpu: use private instead of magic to store cpu id.
Reviewed by: jhb
Silence from: acpi@
MFC after: 2 weeks
X-MFC-Note: perhaps the ivar should stay for ABI stability
sysctl lock. The 'video' lock now protects the 'bus' of video output
devices attached to a graphics adapter. It is used when iterating over
the list of outputs, etc. The 'video_output' lock is used to lock the
output-specific data similar to a driver lock for the individual video
outputs.
MFC after: 2 weeks
startup and genericize it so it can be reused to map other tables as well:
- Add a routine to walk a list of ACPI subtables such as those used in the
APIC and SRAT tables in the MI acpi(4) driver.
- Move the routines for mapping and unmapping an ACPI table as well as
mapping the RSDT or XSDT and searching for a table with a given signature
out into acpica_machdep.c for both amd64 and i386.
BIOS-enumerated devices:
- Assume a device is a match if the memory and I/O ports match even if the
IRQ or DRQ is wrong or missing. Some BIOSes don't include an IRQ for
the atrtc device for example.
- Add a hack to better match floppy controller devices. Many BIOSes do not
include the starting port of the floppy controller listed in the hints
(0x3f0) in the resources for the device. So far, however, all the BIOS
variations encountered do include the 'port + 2' resource (0x3f2), so
adjust the matching for "fdc" devices to look for 'port + 2'.
Reviewed by: imp
MFC after: 3 days
The newbus lock is responsible for protecting newbus internIal structures,
device states and devclass flags. It is necessary to hold it when all
such datas are accessed. For the other operations, softc locking should
ensure enough protection to avoid races.
Newbus lock is automatically held when virtual operations on the device
and bus are invoked when loading the driver or when the suspend/resume
take place. For other 'spourious' operations trying to access/modify
the newbus topology, newbus lock needs to be automatically acquired and
dropped.
For the moment Giant is also acquired in some key point (modules subsystem)
in order to avoid problems before the 8.0 release as module handlers could
make assumptions about it. This Giant locking should go just after
the release happens.
Please keep in mind that the public interface can be expanded in order
to provide more support, if there are really necessities at some point
and also some bugs could arise as long as the patch needs a bit of
further testing.
Bump __FreeBSD_version in order to reflect the newbus lock introduction.
Reviewed by: ed, hps, jhb, imp, mav, scottl
No answer by: ariff, thompsa, yongari
Tested by: pho,
G. Trematerra <giovanni dot trematerra at gmail dot com>,
Brandon Gooch <jamesbrandongooch at gmail dot com>
Sponsored by: Yahoo! Incorporated
Approved by: re (ksmith)
- Preallocate some memory for ACPI tasks early enough. We cannot use
malloc(9) any more because spin mutex may be held here. The reserved
memory can be tuned via debug.acpi.max_tasks tunable or ACPI_MAX_TASKS
in kernel configuration. The default is 32 tasks.
- Implement a custom taskqueue_fast to wrap the new memory allocation.
This implementation is not the fastest in the world but we are being
conservative here.
a _BBN value of 0 if it was for the first bridge encountered since some
older systems returned _BBN of 0 for all bridges. However, some newer
systems enumerate bridges with non-zero _BBN before bus 0 which is
perfectly valid. Handle both cases by trusting the first bridge that has
a _BBN of 0 and falling back to reading from non-standard config registers
only for subsequent bridges with a _BBN of 0. We also only perform this
check for segment (domain) 0. We assume that _BBN is always correct
for segments other than 0.
Tested by: Josef Moellers josef.moellers at fujitsu
MFC after: 1 week
leading to a bug, when C-state does not decrease on sleep shorter then
declared transition latency. Fixing this deprecates workaround for broken
C-states on some hardware.
By the way, change state selecting logic a bit. Instead of last sleep
time use short-time average of it. Global interrupts rate in system is a
quite random value, to corellate subsequent sleeps so directly.
- Probe supported sleep states from acpi_attach() just once and do not
call AcpiGetSleepTypeData() again. It is redundant because
AcpiEnterSleepStatePrep() does it any way.
- Treat UNKNOWN sleep state as NONE, i.e., "do nothing", and remove obscure
NONE state (ACPI_S_STATES_MAX + 1) to avoid confusions.
- Do not set unsupported sleep states as default button/switch events.
If the default sleep state is not supported, just set it as UNKNOWN/NONE.
- Do not allow sleep state change if the system is not fully up and running.
This should prevent entering S5 state multiple times, which causes strange
behaviours later.
- Make sleep states case-insensitive when they are used with sysctl(8).
For example,
sysctl hw.acpi.lid_switch_state=s1
sysctl hw.acpi.sleep_button_state=none
are now legal and equivalent to the uppercase ones.
This change adds (possibly redundant) early check for invalid
state input parameter (including S0). Handling of S5 request
is reduced to simply calling shutdown_nice(). As a result
control flow of acpi_EnterSleepState is somewhat simplified
and resume/backout half of the function is not executed
for S5 (soft poweroff) request and invalid state requests.
Note: it seems that shutdown_nice may act as nop when initproc
is already initialized (to grab pid of 1), but init process is in
"pre-natal" state.
Tested by: Fabian Keil <fk@fabiankeil.de>
Reviewed by: njl, jkim
Approved by: rpaulo
into acpi_cpu_startup() which is where all the other code to update this
global variable lives. This fixes a bug where cpu_cx_count was not updated
correctly if acpi_cpu_generic_cx_probe() returned early.
PR: kern/108581
Debugged by: Bruce Cran
Reviewed by: avg, njl, sepotvin
MFC after: 3 days
This code is heavily inspired by Takanori Watanabe's experimental SMP patch
for i386 and large portion was shamelessly cut and pasted from Peter Wemm's
AP boot code.
This is triggered only if BIOS configures ACPI_BITREG_BUS_MASTER_RLD
aka BRLD_EN_BM to 1.
Rationale:
1. we do not support C3 on PIIX4E
2. bus master activity need not break out of C2 state
3. because of CPU_QUIRK_NO_BM_CTRL quirk we may reset bus master
status which would result in immediate break out from C2
So if you have seen
cpu0: too many short sleeps, backing off to C1
with this chipset before you may want to try cx_lowest of C2 again.
Reviewed by: rpaulo (mentor), njl
Approved by: rpaulo (mentor)
if (batt_sleep_ms)
AcpiOsSleep(1);
where the rest are all:
if (batt_sleep_ms)
AcpiOsSleep(batt_sleep_ms);
I can't recall why that one was different, so change it
to match the rest.
Pointed out by: Christoph Mallon
MFC after: 2 weeks
On some laptops with smart batteries, enabling battery monitoring
software causes keystrokes from atkbd to be lost. This has also been
reported on Linux, and is apparently due to the keyboard and I2C line
for the battery being routed through the same chip. Whether that's
accurate or not, adding extra sleeps to the status checking code
causes the problem to go away.
I've been running this for nearly six months now on my laptop,
it works like a charm.
Reviewed by: Nate Lawson (in a previous revision)
MFC after: 2 weeks
- An "at" hint now reserves a device name.
- A new BUS_HINT_DEVICE_UNIT method is added to the bus interface. When
determining the unit number of a device, this method is invoked to
let the bus driver specify the unit of a device given a specific
devclass. This is the only way a device can be given a name reserved
via an "at" hint.
- Implement BUS_HINT_DEVICE_UNIT() for the acpi(4) and isa(4) bus drivers.
Both of these busses implement this by comparing the resources for a
given hint device with the resources enumerated by ACPI/PnPBIOS and
wire a unit if the hint resources are a subset of the "real" resources.
- Use bus_hinted_children() for adding hinted devices on isa(4) busses
now instead of doing it by hand.
- Remove the unit kludging from sio(4) as it is no longer necessary.
Prodding from: peter, imp
OK'd by: marcel
MFC after: 1 month
use process ID as ACPI thread ID. Concurrent requests with equal thread
IDs broke ACPI mutexes operation causing unpredictable errors including
AE_AML_MUTEX_NOT_ACQUIRED that I have seen.
Use kernel thread ID instead of process ID for ACPI thread.
- Rename pciereg_cfgopen() to pcie_cfgregopen() and expose it to the
rest of the kernel. It now also accepts parameters via function
arguments rather than global variables.
- Add a notion of minimum and maximum bus numbers and reject requests for
an out of range bus.
- Add more range checks on slot/func/reg/bytes parameters to the cfg reg
read/write routines. Don't panic on any invalid parameters, just fail
the request (writes do nothing, reads return -1). This matches the
behavior of the other cfg mechanisms.
- Port the memory mapped configuration space access to amd64. On amd64
we simply use the direct map (via pmap_mapdev()) for the memory mapped
window.
- During acpi_attach() just after loading the ACPI tables, check for a
MCFG table. If it exists, call pciereg_cfgopen() on each subtable
(memory mapped window). For now we only support windows for domain 0
that start with bus 0. This removes the need for more chipset-specific
quirks in the MD code.
- Remove the chipset-specific quirks for the Intel 5000P/V/Z chipsets
since these machines should all have MCFG tables via ACPI.
- Updated pci_cfgregopen() to DTRT if ACPI had invoked pcie_cfgregopen()
earlier.
MFC after: 2 weeks
behavior. Specifically, probe Host-PCI bridges in the order they are
encountered in the tree. For CPUs, just use an order of 100000 and assume
that no Host-PCI bridges will be more than 10000 levels deep in the
namespace. This fixes an issue on some boxes where the HPET timer stopped
attaching.
assumptions about the state of the cooling devices. Instead, switch them
off on init and, only after that, we are in TZ_ACTIVE_NONE.
Submited by: Andriy Gapon <avg at icyb.net.ua>
Reviewed by: njl
different "platforms" on x86 machines. The existing code already handles
having two platforms: ACPI and legacy. However, the existing approach was
rather hardcoded and difficult to extend. These changes take the approach
that each x86 hardware platform should provide its own nexus(4) driver (it
can inherit most of its behavior from the default legacy nexus(4) driver)
which is responsible for probing for the platform and performing
appropriate platform-specific setup during attach (such as adding a
platform-specific bus device). This does mean changing the x86 platform
busses to no longer use an identify routine for probing, but to move that
logic into their matching nexus(4) driver instead.
- Make the default nexus(4) driver in nexus.c on i386 and amd64 handle the
legacy platform. It's probe routine now returns BUS_PROBE_GENERIC so it
can be overriden.
- Expose a nexus_init_resources() routine which initializes the various
resource managers so that subclassed nexus(4) drivers can invoke it from
their attach routine.
- The legacy nexus(4) driver explicitly adds a legacy0 device in its
attach routine.
- The ACPI driver no longer contains an new-bus identify method. Instead
it exposes a public function (acpi_identify()) which is a probe routine
that the MD nexus(4) drivers can use to probe for ACPI. All of the
probe logic in acpi_probe() is now moved into acpi_identify() and
acpi_probe() is just a stub.
- On i386 and amd64, an ACPI-specific nexus(4) driver checks for ACPI via
acpi_identify() and claims the nexus0 device if the probe succeeds. It
then explicitly adds an acpi0 device in its attach routine.
- The legacy(4) driver no longer knows anything about the acpi0 device.
- On ia64 if acpi_identify() fails you basically end up with no devices.
This matches the previous behavior where the old acpi_identify() would
fail to add an acpi0 device again leaving you with no devices.
Discussed with: imp
Silence on: arch@
the cpufreq drivers to reliably use properties of PCI devices for quirks,
etc.
- For the legacy drivers, add CPU devices via an identify routine in the
CPU driver itself rather than in the legacy driver's attach routine.
- Add CPU devices after Host-PCI bridges in the acpi bus driver.
- Change the ichss(4) driver to use pci_find_bsf() to locate the ICH and
check its device ID rather than having a bogus PCI attachment that only
checked for the ID in probe and always failed. As a side effect, you
can now kldload ichss after boot.
- Fix the ichss(4) driver to use the correct device_t for the ICH (and not
for ichss0) when doing PCI config space operations to enable SpeedStep.
MFC after: 2 weeks
Reviewed by: njl, Andriy Gapon avg of icyb.net.ua
the appropriate bit in the DEVACTB register.
This change allows the C2 state on those systems to work as expected.
Reviewed by: njl
Submitted by: Andriy Gapon <avg at icyb.net.ua>
MFC after: 1 week
spec:
- Use read/modify/write cycles to enable and disable the HPET instead of
writing 0 to reserved bits.
- Shutdown the HPET during suspend as encouraged by the spec.
- Fail to attach to an HPET with a period of zero.
MFC after: 1 week
PR: kern/119675 [3]
Reported by: Leo Bicknell | bicknell ufp.org
zone code. The GPE handler method (i.e. _L00) generates various Notify
events that need to be run to completion before the GPE is re-enabled.
In ACPI-CA, we queue an asynch callback at the same priority as a Notify
so that it will only run after all Notify handlers have completed. The
callback re-enables the GPE afterwards. We also changed the priority of
Notifies to be the same as GPEs, given the possibility that another GPE
could arrive before the Notifies have completed and we don't want it to
get queued ahead of the rest.
The ACPI-CA change was submitted by Alexey Starikovskiy (SUSE) and will
appear in a later release. Special thanks to him for helping track this
bug down.
MFC after: 1 week
Tested by: jhb, Yousif Hassan <yousif / alumni.jmu.edu>
correct number of acpi_thermalX devices. Having this wrong caused the
acpi_thermal thread to realloc the array of devices on each loop iteration.
MFC after: 1 week
PR: kern/118497
Submitted by: Pasi Parviainen
for that argument. This will allow DDB to detect the broad category of
reason why the debugger has been entered, which it can use for the
purposes of deciding which DDB script to run.
Assign approximate why values to all current consumers of the
kdb_enter() interface.
CPUs to make sure idle threads are evicted from the softc before returning
from acpi_cpu_shutdown(). However, this is unnecessary since stop_cpus()
handles this for itself and at this point it's possible that our IPI will be
blocked (interrupts disabled).
Thanks to: Glen Leeder <glen.leeder / nokia.com>
MFC after: 3 days
reason (not all BIOSen have _DIS methods for all link devices for example).
This matches the behavior of attach() with respect to _DIS as well.
Submitted by: njl
handle to the PCI device_t if the ACPI device_t is already attached to a
driver. This happens on the Tablet TC1000 which for some reason includes
two PCI-ISA bridges and treats the second bridge as an ACPI system resource
device.
Reviewed by: njl (a while ago)
MFC after: 3 days
