Unfortunately (sigh) some firmware doesn't provide the RX BA starting point,
so we need to cope and set a "close enough" sequence number so we (hopefully!)
don't discard frames as duplicates.
Tested:
* QCA9880v2, athp driver (under development), STA mode
Also - allow driver specific bits to be added, rather than just net80211.
This still isn't as useful as it should be by default; it needs to
be a standalone struct/instance so it can be done before net80211
registration occurs, and it can log per-device items.
But, it's getting there.
* extend the keycache flag word to be 32 bits, not 16 bits
* add new key flags for transmit:
+ IEEE80211_KEY_NOIV: Don't insert IV in the payload when transmitting data frames;
+ IEEE80211_KEY_NOIVMGT: Don't insert IV in the payload when transmitting MIC frames;
+ IEEE80211_KEY_NOMIC: Don't insert MIC in the payload when transmitting data frames;
+ IEEE80211_KEY_NOMICMGT: don't insert MIC in the payload when transmitting management
frames.
* teach ieee80211_crypto_demic() about hardware decrypted frames:
+ if frames are hardware decrypted and the frame has failed MIC, treat it as a
michael failure.
+ if frames are hardware decrypted and the frame has stripped MIC, we can't check the
MIC in the payload - we don't have anything to compare it against.
This is only part of the work required to successfully transmit/receive
hardware crypto frames such as the qualcomm atheros 11ac offload chips.
There will be further work in the transmit and receive path before this
can be done by default.
Reviewed by: avos
Differential Revision: https://reviews.freebsd.org/D8364
This is a very simple addition to the net80211 scan support.
It doesn't implement a replacement scan interface - it just disables
the pieces that we should disable to make this lifecycle a bit
more managable.
There's more work to come before full scan offload support is available
but it should be good enough for driver work.
* add a flag to say "full offload"
* don't do probe requests when scanning full-offload - firmware can do that
* don't do powersave transitions and buffering - firmware can do that
tested:
* iwm(4) - STA mode
* ath10k port (local, not in freebsd-head yet)
Reviewed by: avos
Differential Revision: https://reviews.freebsd.org/D8262
to ieee80211_add_rx_params() + drop last (ieee80211_rx_stats) parameter
Note: there is an additional check for ieee80211_get_rx_params()
return value (which does not exist in the original diff).
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D8207
There are a variety of more interesting RX statistics that we should
keep track of but we don't. This is a starting point for adding more
information.
Specifically:
* now the RX rate information and some of the packet status is
passed up;
* The 32 bit or 64 bit TSF is passed up;
* the PHY mode is passed up;
* the "I'm decap'ed AMSDU!" state is passed up;
* number of RX chains is bumped to 4.
This is all mostly a placeholder for getting the data into the RX status
before we pass it up to net80211 - unfortunately we don't yet enforce
that drivers provide it, nor do we pass the provided info back up the
stack so anyone can use the data.
We're going to need to use some of this data moving forward.
Notably, now that some hardware can do AMSDU decap for us (the intel iwm
driver can do it when we flip it on; the ath10k port I'm doing does
it for us) then we need to pass it up through the stack so the duplicate
RX sequence numbers and crypto/IV details don't cause the packet to
be dropped and/or counted against a replay counter.
It's also the beginning of being able to do more interesting node
accounting in net80211. Specifically, once drivers start populating
per-packet rate information, AMPDU information, timestamps, etc,
we can start providing histograms of rate-versus-RSSI, account
for receive time spent per node and other such interesting things.
(Note: I'm also hoping to include ranging and RTT information for
future chipset support; and it's likely going to include it in
this kind of fashion.)
Replace various void * / int argument combinations with common structures:
- ieee80211_ratectl_tx_status for *_tx_complete();
- ieee80211_ratectl_tx_stats for *_tx_update();
While here, improve amrr_tx_update() for a bit:
1. In case, if receiver is not known (typical for Ralink USB drivers),
refresh Tx rate for all nodes on the interface.
2. There was a misuse:
- otus(4) sends non-decreasing counters (as originally intended);
- but ural(4), rum(4) and run(4) are using 'read & clear' registers
to obtain statistics for some period of time (and those 'last period'
values are used as arguments for tx_update()). If arguments are not big
enough, they are just discarded after the next call.
Fix: move counting into *_tx_update()
(now otus(4) will zero out all node counters after every tx_update() call)
Tested with:
- Intel 3945BG (wpi(4)), STA mode.
- WUSB54GC (rum(4)), STA / HOSTAP mode.
- RTL8188EU (urtwn(4)), STA mode.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D8037
- Add a counter into 'struct ieee80211_node_table' to save current number
of allocated nodes.
(allows to remove array overflow checking in ieee80211_iterate_nodes()).
- Add ieee80211_iterate_nodes_vap() function; unlike non-vap version,
it iterates on nodes for specified vap only.
In addition to the above:
- Remove ieee80211_iterate_nt(); it is not used by drivers / net80211
outside ieee80211_iterate_nodes() function + cannot be separated due
to structural changes in code.
Since size of 'struct ieee80211_node_table' (part of ieee80211com,
which is a part of driver's softc) is changed all wireless drivers /
kernel need to be recompiled.
Tested with wpi(4), STA mode.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D7996
Restore pre-r300383 behavior when a frame is sent:
- stop scan;
- send frame;
- when beacon arrives and our bit in TIM is not set - restart the scan.
NOTE:
Ideally, this should introduce new interface (ieee80211_pause_anyscan());
however, since ieee80211_cancel_anyscan() is not used by drivers and only
called by ieee80211_start_pkt() the current patch overrides it's behavior
instead.
Tested with Intel 3945BG, STA mode
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D7979
The adhoc probe/beacon input path was creating nodes for all SSIDs.
This wasn't a problem when the NICs were configured to only process
frames for the current BSSID, but that didn't allow IBSS merges.
Once avos and I flipped on "beacons from all BSSIDs" to allow for
correct IBSS merging, we found this interesting behaviour.
This adds a check against the current SSID.
* If there's no VAP SSID, allow anything
* If there's a VAP SSID, check if the incoming frame has a suitable
SSID and if so, allow it.
This prevents nodes being created for other SSIDs in probe and beacon
frames - ie, beacons overlapping IBSSes with different SSIDs, and
probe requests from arbitrary devices.
Tested:
* AR9380, IBSS mode, both local and other IBSSes.
Reviewed by: avos
Differential Revision: https://reviews.freebsd.org/D7959
IBSS negotiation is a subset of the STA/AP negotiation. We always have a
current channel, so base the HT capabilities on the current channel.
This is then put into IBSS probe requests to inform peers of our
11n capabilities.
Add IEEE80211_KEY_SWCRYPT / IEEE80211_KEY_SWMIC bits to the
IEEE80211_KEY_DEVICE mask - as a result, those bits will be preserved
during group key handshake.
A driver can override them in iv_key_alloc() for some keys in case
when hardware crypto support is not possible. As an example:
- multi-vap without multicast key search support;
- IBSS RSN for devices w/ fixed storage for group keys;
Tested with RTL8188EU (AP, sw crypto) and
RTL8821AU (STA, sw crypto for group keys + hw crypto for pairwise keys)
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D7901
- Add few checks for group/pairwise ciphers into
ieee80211_parse_{wpa,rsn}().
- Split error code and cipher value in wpa_cipher() / rsn_cipher(); current
hack with (1 << 32) does not work - it's 1, not 0 (detected by CSA).
- Return IEEE80211_REASON_UNSUPP_RSN_IE_VERSION instead of
IEEE80211_REASON_IE_INVALID when version field is not equal to RSN_VERSION.
Tested with wpi(4) / urtwn(4) (HOSTAP mode).
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D7887
In case if there is already running interface, a second non-sta
interface will omit scanning, going directly to RUN state. Handle
this case for adhoc mode appropriately.
Tested with RTL8821AU, 2 vaps in IBSS mode.
Uses of commas instead of a semicolons can easily go undetected. The comma
can serve as a statement separator but this shouldn't be abused when
statements are meant to be standalone.
Detected with devel/coccinelle following a hint from DragonFlyBSD.
MFC after: 1 month
turn them into a shared definition.
Set M_MCAST/M_BCAST appropriately upon packet reception in net80211, just
before they are delivered up to the ethernet stack.
Submitted by: rstone
Add new lock for stageq (part of ieee80211_superg structure) and
ni_tx_superg (part of ieee80211_node structure);
drop com_lock protection where it is used to protect them.
While here, drop duplicate OPACKETS counter incrementation.
ni_tx_ampdu is not protected with it (however, it is also used without
locking in other places; probably, it requires some other solution
to be thread-safe).
Tested with RTL8188CUS (AP) and RTL8188EU (STA).
NOTE: Since this change breaks KBI, all wireless drivers need to be
recompiled.
Reviewed by: adrian
Approved by: re (gjb)
Differential Revision: https://reviews.freebsd.org/D6958
avos@ pointed out to me that this broke IBSS merging because the rest of
the input path no longer was called for non-IBSS frames.
I committed a change to not input non-IBSS frames, which stopped
nodes being created for BSSes that weren't ours. Unfortunately
thta stopped the input path for non-IBSS frames in general,
so the management input path didn't work.
So, I'll revert this until I come up with a better solution.
(Hopefully before 11.)
Reviewed by: avos
Approved by: re (gjb)
Drop scan generation number and node table scan lock - the only place
where ni_scangen is checked is in ieee80211_timeout_stations() (and it
is used to prevent duplicate checking of the same node); node scan lock
protects only this variable + node table scan generation number.
This will fix (at least) next LOR (hostap mode):
lock order reversal:
1st 0xc175f84c urtwm0_scan_loc (urtwm0_scan_loc) @ /usr/src/sys/modules/wlan/../../net80211/ieee80211_node.c:2019
2nd 0xc175e018 urtwm0_com_lock (urtwm0_com_lock) @ /usr/src/sys/modules/wlan/../../net80211/ieee80211_node.c:2693
stack backtrace:
#0 0xa070d1c5 at witness_debugger+0x75
#1 0xa070d0f6 at witness_checkorder+0xd46
#2 0xa0694cce at __mtx_lock_flags+0x9e
#3 0xb03ad9ef at ieee80211_node_leave+0x12f
#4 0xb03afd13 at ieee80211_timeout_stations+0x483
#5 0xb03aa1c2 at ieee80211_node_timeout+0x42
#6 0xa06c6fa1 at softclock_call_cc+0x1e1
#7 0xa06c7518 at softclock+0xc8
#8 0xa06789ae at intr_event_execute_handlers+0x8e
#9 0xa0678fa0 at ithread_loop+0x90
#10 0xa0675fbe at fork_exit+0x7e
#11 0xa08af910 at fork_trampoline+0x8
In addition to the above:
* switch to ieee80211_iterate_nodes();
* do not assert that node table lock is held, while calling node_age();
that's not really needed (there are no resources, which can be protected
by this lock) + this fixes LOR/deadlock between ieee80211_timeout_stations()
and ieee80211_set_tim() (easy to reproduce in HOSTAP mode while
sending something to an STA with enabled power management).
Tested:
* (avos) urtwn0, hostap mode
* (adrian) AR9380, STA mode
* (adrian) AR9380, AR9331, AR9580, hostap mode
Notes:
* This changes the net80211 internals, so you have to recompile all of it
and the wifi drivers.
Submitted by: avos
Approved by: re (delphij)
Differential Revision: https://reviews.freebsd.org/D6833
Do not try to pass such frames; a correct frame cannot be smaller than
(the corresponding) header size.
(for wpi(4) an additional check was added in r289012).
PR: 144987
Remove 'if_inc_counter(ifp, IFCOUNTER_OPACKETS, 1);' from raw xmit
and apbridge path; it will be incremented by ieee80211_tx_complete()
after packet transmission.
Noticed by: Imre Vadasz <imre@vdsz.com>
- Assign frame sequence/fragment number before frame concatenation;
otherwise, frame header pointer (wh) will be invalid.
- Move this code block upper and eliminate duplicate 'lwh = mtod()'
assignment.
Tested with wpi(4) (transmitter) (STA mode) and urtwn(4) (receiver)
(HOSTAP mode).
Change default regulatory domain from DEBUG (no limitations;
exposes all device channels) to FCC; as a result, newly created wireless
interface with default settings will have less chances to violate
country-specific regulations.
This change will not affect drivers with pre-initialized regdomain
structure (currentry ath(4) and mwl(4)); in that case, the default
channel list must correspond to the default regdomain / country setting.
You can switch to another regdomain / country via corresponding
ifconfig(8) options; the driver must implement ic_getradiocaps()
method to restore full channel list.
Full country / regdomain list may be obtained via
'ifconfig <iface> list countries' command.
Example: change country to Germany:
ifconfig wlan0 down # all wlans on the device must be down
ifconfig wlan0 country DE
ifconfig wlan0 up
# wpa_supplicant(8), dhclient(8) etc
At the creation time:
ifconfig wlan0 create wlandev wpi0 country DE
To make changes permanent add the following line to the rc.conf(5):
create_args_wlan0="country DE"
Tested with
- Intel 3945BG (wpi(4)).
- WUSB54GC (rum(4)).
Reviewed by: adrian
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D6228
wpa_supplicant(8) expects to see 'scan complete' event after every
scan command; in case, when event is not sent it will hang for
indefinite time.
PR: 209198
Do not try to start a scan when interface is not running.
How-to-reproduce:
1) ifconfig wlan0 create wlandev urtwn0
2) wlandebug -i wlan0 state
3) ifconfig wlan0 scan
ieee80211.c:
add_chanlist(): 'error' variable will be uninitialized if
no channels were passed; return '0' instead.
ieee80211_action.c:
ieee80211_send_action_register(): drop 'break' after 'return'.
ieee80211_crypto_none.c:
none_encap(): 'keyid' is not used in non-debug builds; hide it
behind IEEE80211_DEBUG ifdef.
ieee80211_freebsd.c:
Staticize global 'ieee80211_debug' variable (used only in this
file).
ieee80211_hostap.c:
Fix a comment (associatio -> association).
ieee80211_ht.c:
ieee80211_setup_htrates(): initialize 'maxunequalmcs' to 0 to mute
compiler warning.
ieee80211_hwmp.c:
hwmp_recv_preq(): copy 'prep' between conditional blocks to fix
-Wshadow warning.
ieee80211_mesh.c:
mesh_newstate(): remove duplicate 'ni' definition.
mesh_recv_group_data(): fix -Wempty-body warning in non-debug
builds.
ieee80211_phy.c:
ieee80211_compute_duration(): remove 'break' after panic() call.
ieee80211_scan_sta.c:
Hide some TDMA-specific macros under IEEE80211_SUPPORT_TDMA ifdef
adhoc_pick_bss(): remove 'ic' pointer redefinition.
ieee80211_sta.c:
sta_beacon_miss(): remove 'ic' pointer redefinition.
ieee80211_superg.c:
superg_ioctl_set80211(): drop unreachable return.
Tested with clang 3.8.0, gcc 4.6.4 and gcc 5.3.0.
Replace ifnet list lookup (which is broken since r287197, because
IFT_IEEE80211 type is not used anymore) with iteration on
ieee80211com list.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D6419
again hopefully.
Rather than blindly removing a supposedly unused variable as reported by
the Clang Static Analyzer, inspect the code and hide them with proper
#ifdefs as they are used in certain conditional parts of the code.
