completenss. The pessimization is tiny compared with i/o port slowness
except on very old machines, but code that used signed short types for
i/o ports was unpessimized long ago, and the macro that detected it
recently started working for u_short types too. Use of bus space
should have made this moot long ago.
Not tested at runtime by: bde
network layer (ether).
- Don't abuse module names to facilitate ifconfig module loading;
such abuse isn't really needed. (And if we do need type information
associated with a module then we should make it explicit and not
use hacks.)
is required. NetBSD has one because it checks for the mac address
match as well wanting to give its own string in the description.
Since we do neither, we don't need a separate entry.
# I suspect that a few of the COREGA cards might fall into that category
# as well, but since I don't have access to any of them it is hard to know
# for sure.
enet_mcast fields, so remove them. Sort. Eliminate now duplicate
entries.
This reorg saves about 500 bytes in the binary. I've tested this only
with a couple of cards, so please let me know if I've broken anything.
where physical addresses larger than virtual addresses, such as i386s
with PAE.
- Use this to represent physical addresses in the MI vm system and in the
i386 pmap code. This also changes the paddr parameter to d_mmap_t.
- Fix printf formats to handle physical addresses >4G in the i386 memory
detection code, and due to kvtop returning vm_paddr_t instead of u_long.
Note that this is a name change only; vm_paddr_t is still the same as
vm_offset_t on all currently supported platforms.
Sponsored by: DARPA, Network Associates Laboratories
Discussed with: re, phk (cdevsw change)
o don't strip the Ethernet header from inbound packets; pass packets
up the stack intact (required significant changes to some drivers)
o reference common definitions in net/ethernet.h (e.g. ETHER_ALIGN)
o track ether_ifattach/ether_ifdetach API changes
o track bpf changes (use BPF_TAP and BPF_MTAP)
o track vlan changes (ifnet capabilities, revised processing scheme, etc.)
o use if_input to pass packets "up"
o call ether_ioctl for default handling of ioctls
Reviewed by: many
Approved by: re
o Honor NE2000DVF_{AX88190,DL10019} flags by setting the ED_FLAGS_xxxx
flag.
o Mark linksys combo_ecard as ax88190
o Set the type_str to AX88190 for the ax88190 cards.
This fixes ax88190 based cards, for the most part, but doesn't seem to fix
the mii based dl10019 cards (aka linksys cards).
card is ejected while we're in this routine.
yamamoto-san's original patch had a small race window for AX88190
chips, which I corrected by limiting the number of iterations we'd try
to reset the bits to be about 15ms rather than forever. This seems to
work for me, but I don't have a large collections of cards based on
this chipset.
Submitted by: YAMAMOTO Shigeru
built without support for miibus PHYs. Most ed cards don't need
miibus support, so it's useful to be able to avoid the bloat of
all the mii devices for small fixed-purpose kernels.
storing a flag in the global variable 'linksys' during the probe
routine and reading it during the attach routine. We now have the
ED_VENDOR_LINKSYS vendor code stored in sc->vendor, so check that
instead.
not from the probe routine. This was an oversight when I originally
ported the miibus support to -current, though it was mostly harmless.
We now set the vendor code to the new value ED_VENDOR_LINKSYS in
ed_pccard_Linksys() at probe time. Then ed_pccard_attach() checks
the vendor code, and sets up the miibus if appropriate.
Reviewed by: imp
bolted to a ne-2000 chip. This is necessary for the NetGear FA-410TX
and other cards.
This also requires you add mii to your kernel if you have an ed driver
configured.
This code will result in a couple of timeout messages for ed on the
impacted cards. Additional work will be needed, but this does work
right now, and many people need these cards.
Submitted by: Ian Dowse <iedowse@maths.tcd.ie>
* a ">" is really ">=" ;
* do not try to fetch zero-sized blocks from the card;
* make sure that bpf gets the packets it wants even with
bridging active;
