required for the ABI the kernel is being built for.
XXX This is implemented in a kind-of nasty way that involves including source
files, but it's still an improvement.
o) Retire ISA_* options since they're unused and were always wrong.
stack. It means that all legacy ATA drivers are disabled and replaced by
respective CAM drivers. If you are using ATA device names in /etc/fstab or
other places, make sure to update them respectively (adX -> adaY,
acdX -> cdY, afdX -> daY, astX -> saY, where 'Y's are the sequential
numbers for each type in order of detection, unless configured otherwise
with tunables, see cam(4)).
ataraid(4) functionality is now supported by the RAID GEOM class.
To use it you can load geom_raid kernel module and use graid(8) tool
for management. Instead of /dev/arX device names, use /dev/raid/rX.
mipsel' or 'machine mips mipseb' into the config file (with a few 64's
tossed in for good measure). This will let us build the proper
kernels with different worlds as part of make universe.
the 'debugging' section of any HEAD kernel and enable for the mainstream
ones, excluding the embedded architectures.
It may, of course, enabled on a case-by-case basis.
Sponsored by: Sandvine Incorporated
Requested by: emaste
Discussed with: kib
I think these are the relevant changes, but definitely are a superset
of them. Software archaeologists are invited to check the branch
itself for the details.
r199695 | imp | 2009-11-23 00:49:50 -0700 (Mon, 23 Nov 2009) | 2 lines
Specify loader script and load address
r198263 | neel | 2009-10-19 22:31:20 -0600 (Mon, 19 Oct 2009) | 7 lines
The default KERNLOADADDR does not work on MALTA hardware. On my platform the
"First free SDRAM address" reported by YAMON is 0x800b6e61.
So use a conservative KERNLOADADDR of 0x80100000.
Approved by: imp (mentor)
r194163 | imp | 2009-06-14 00:12:21 -0600 (Sun, 14 Jun 2009) | 2 lines
Kludge: pretend to be ISA_MIPS32 for the moment.
r192864 | gonzo | 2009-05-26 16:40:12 -0600 (Tue, 26 May 2009) | 4 lines
- Replace CPU_NOFPU and SOFTFLOAT options with CPU_FPU. By default
we assume that there is no FPU, because majority of SoC does
not have it.
r187461 | gonzo | 2009-01-19 21:24:03 -0700 (Mon, 19 Jan 2009) | 3 lines
- KERNLOADADDR should be defined with makeoption.
Redboot loads kernel now
r187418 | gonzo | 2009-01-18 19:37:10 -0700 (Sun, 18 Jan 2009) | 4 lines
- Add trampoline stuff for bootloaders that do not support ELF
- Replace arm'ish KERNPHYSADDR/KERNVIRTADDR with
KERNLOADADDR/TRAMPLOADADDR and clean configs
machine arm
device mem
device uart_ns8250
options GEOM_BSD
options GEOM_MBR
Remove the first three from all kernel configuration files
(sometimes commented-out) and change geom_bsd and geom_mbr
from standard to optional.
mips32r2 and mips64r2 (and close relatives) processors. There
presently is support for ADMtek ADM5120, A mips 4Kc in a malta board,
the RB533 routerboard (based on IDT RC32434) and some preliminary
support for sibtye/broadcom designs. Other hardware support will be
forthcomcing.
This port boots multiuser under gxemul emulating the malta board and
also bootstraps on the hardware whose support is forthcoming...
Oleksandr Tymoshenko, Wojciech Koszek, Warner Losh, Olivier Houchard,
Randall Stewert and others that have contributed to the mips2 and/or
mips2-jnpr perforce branches. Juniper contirbuted a generic mips port
late in the life cycle of the misp2 branch. Warner Losh merged the
mips2 and Juniper code bases, and others list above have worked for
the past several months to get to multiuser.
In addition, the mips2 work owe a debt to the trail blazing efforts of
the original mips branch in perforce done by Juli Mallett.
