This driver works in PIO mode for now, interrupts are available only when
FIFO is enabled. The FIFO cannot be used with arbitrary sizes which defeat
its general use.
At some point we can add DMA transfers where the FIFO can be more useful.
Tested on uBMC (microBMC) and BBB.
Sponsored by: Rubicon Communications (Netgate)
a DRIVER_MODULE() referencing mmc_driver has a MODULE_DEPEND() on mmc. This
is because the kernel linker only searches for symbols in dependent modules,
so loading sdhci_pci (and other bus-flavors of sdhci) would fail when mmc
was not compiled into the kernel (even if you hand-loaded mmc first).
(Thanks to jilles@ for providing the vital clue about the kernel linker.)
In dual emac mode, the CPSW subsystem provides two independent ethernets.
This is implemented (as recommended by TI's TRM) with a mixture of switch
settings (vlans) and specific features of CPSW subsystem.
The driver was splitted to accommodate the shared parts (RX and TX rings
for example) while it still provides two independent ethernets.
Each of the ethernet ports driver has it's own set of MDIO registers among
the other private settings.
Previously this driver always operate in promisc mode, now the Switch ALE
(address table entry) is properly initialized and enabled.
The driver is also tested (and known to work) with both ports operating in
single port mode (active_slave 0 or 1).
Tested on uBMC (dual emac mode, both ports in single mode, giga and fast
ethernet) and BBB (single port, fast ethernet).
Sponsored by: Rubicon Communications (Netgate)
taskqueue_enqueue() was changed to support both fast and non-fast
taskqueues 10 years ago in r154167. It has been a compat shim ever
since. It's time for the compat shim to go.
Submitted by: Howard Su <howard0su@gmail.com>
Reviewed by: sephe
Differential Revision: https://reviews.freebsd.org/D5131
intr_pic_init_secondary. Replace them with a direct call. On BCM2836
and ARMADA XP we need to add this function, but it can be empty.
Reviewed by: ian, imp
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D5460
slightly wrong on the others. We should just check if mp_ncpus is set to
more than one CPU as we may wish to run on a single core even when SMP is
available.
Reviewed by: ian
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D5458
Only L2 PIPT cache is supported for __ARM_ARCH >= 6.
In fact, this is just a pure proclamation as this option is used
only in armv4 specific files now.
am335x_prcm driver which uses it. Used BUS_PASS_BUS is a quick pick
for now and may be revised when other drivers start using multipass
feature.
This is needed after an update of Linux dts files done in r295436.
The ci20 port (by kan@) is going to reuse almost all of the intrng code
since the SoC in question looks suspiciously like someone took an ARM
SoC design and replaced the ARM core with a MIPS core.
* migrate out the code;
* rename ARM_ -> INTR_;
* rename arm_ -> intr_;
* move the interrupt flush routine from intr.c / intrng.c into
arm/machdep_intr.c - removing the code duplication and removing
the ARM specific bits from here.
Thanks to the Star Wars: The Force Awakens premiere line for allowing
me a couple hours of quiet time to finish the universe builds.
Tested:
* make universe
TODO:
* The structure definitions in subr_intr.c still includes machine/intr.h
which requires one duplicates all of the intrng definitions in
the platform code (which kan has done, and I think we don't have to.)
Instead I should break out the generic things (function declarations,
common intr structures, etc) into a separate header.
* Kan has requested I make the PIC based IPI stuff optional.
variable during mp_start() which is too late. Move this to mp_setmaxid()
where other architectures set it and move x86 assertions to MI code.
Reviewed by: kib (x86 part)
represented in 7-bits format in DT files, but system expect it in 8-bit
format. Also, fix two drivers that locally hack around this bug.
Submitted by: Michal Meloun <meloun@miracle.cz>
the name the function will have when the new ARM_INTRNG code is integrated,
and doing this rename first will make it easier to toggle the new interrupt
handling code on/off with a config option for debugging.
specific as we may use the pmu registers for other uses. No configs seem
to currently build this.
This will allow for more use of this device.
Discussed with: bz
Sponsored by: ABT Systems Ltd
redoing it as a separate driver. Now that each hardware timer is handled by
a separate instance of the timer driver, it no longer makes sense to bundle
the pps driver with the regular timecounter code. (When all 8 timers were
handled by one driver there was no choice about this.)
Split the hardware register definitions out to their own file, so that the
new pps driver (coming in a separate commit later) can share them.
With the PPS driver gone, the question of which hardware timer to use for
what purpose becomes much easier (some instances can't do the PPS capture).
Now we can just hardcore timer2 for eventtimer and timer3 for timecounter.
This also now only instantiates devices for the 2 hardware timers actually
used to implement eventtimer and timecounter. This is required so that
other drivers can come along and attach to other hardware timers to provide
other functionality. (In addition to PPS, this hardware can also do PWM
stuff, general pulse width and frequency measurements, etc. Maybe some
day we'll have drivers for those things.)
given the hardware name.
The ti,hwmods property is used (among other things) to associate an fdt node
with a specific instance of some hardware. For example given a device node
that contains the property ti,hwmods = "timer3", if you call this passing
"timer" as the hwmod string to look for it would return 3.
Some of FDT blobs for AM335x-based devices use pinmux pullup/pulldown
flag to setup initial GPIO ouputp value, e.g. 4DCAPE-43 sets LCD DATAEN
signal this way. It works for Linux because Linux driver does not enforce
pin direction until after it's requested by consumer. So input with pullup
flag set acts as output with GPIO_HIGH value
Reviewed by: loos
