install or remove non-SCI interrupt handlers per ACPI Component Architecture
User Guide and Programmer Reference. ACPICA may install such interrupt
handler when a GPE block device is found, for example. Add a wrapper for
ACPI_OSD_HANDLER, convert its return values to ours, and make it a filter.
Prefer KASSERT(9) over panic(9) as we have never seen those in reality.
Clean up some style(9) nits and add my copyright.
method is used by the PCI bus driver to query the power management system
to determine the proper device state to be used for a device during suspend
and resume. For the ACPI PCI bridge drivers this calls
acpi_device_pwr_for_sleep(). This removes ACPI-specific knowledge from
the PCI and PCI-PCI bridge drivers.
Reviewed by: jkim
device, make sure we have no real HPET device entry with same ID.
As side effect, it potentially allows several HPETs to be attached.
Use first of them for timecounting, rest (if ever present) could later
be used as event sources.
o acpi_hpet: auto-added 'wildcard' devices can be identified by
non-NULL handle attribute.
o acpi_ec: auto-add 'wildcard' devices can be identified by
unset (NULL) private attribute.
o acpi_cpu: use private instead of magic to store cpu id.
Reviewed by: jhb
Silence from: acpi@
MFC after: 2 weeks
X-MFC-Note: perhaps the ivar should stay for ABI stability
startup and genericize it so it can be reused to map other tables as well:
- Add a routine to walk a list of ACPI subtables such as those used in the
APIC and SRAT tables in the MI acpi(4) driver.
- Move the routines for mapping and unmapping an ACPI table as well as
mapping the RSDT or XSDT and searching for a table with a given signature
out into acpica_machdep.c for both amd64 and i386.
- Preallocate some memory for ACPI tasks early enough. We cannot use
malloc(9) any more because spin mutex may be held here. The reserved
memory can be tuned via debug.acpi.max_tasks tunable or ACPI_MAX_TASKS
in kernel configuration. The default is 32 tasks.
- Implement a custom taskqueue_fast to wrap the new memory allocation.
This implementation is not the fastest in the world but we are being
conservative here.
different "platforms" on x86 machines. The existing code already handles
having two platforms: ACPI and legacy. However, the existing approach was
rather hardcoded and difficult to extend. These changes take the approach
that each x86 hardware platform should provide its own nexus(4) driver (it
can inherit most of its behavior from the default legacy nexus(4) driver)
which is responsible for probing for the platform and performing
appropriate platform-specific setup during attach (such as adding a
platform-specific bus device). This does mean changing the x86 platform
busses to no longer use an identify routine for probing, but to move that
logic into their matching nexus(4) driver instead.
- Make the default nexus(4) driver in nexus.c on i386 and amd64 handle the
legacy platform. It's probe routine now returns BUS_PROBE_GENERIC so it
can be overriden.
- Expose a nexus_init_resources() routine which initializes the various
resource managers so that subclassed nexus(4) drivers can invoke it from
their attach routine.
- The legacy nexus(4) driver explicitly adds a legacy0 device in its
attach routine.
- The ACPI driver no longer contains an new-bus identify method. Instead
it exposes a public function (acpi_identify()) which is a probe routine
that the MD nexus(4) drivers can use to probe for ACPI. All of the
probe logic in acpi_probe() is now moved into acpi_identify() and
acpi_probe() is just a stub.
- On i386 and amd64, an ACPI-specific nexus(4) driver checks for ACPI via
acpi_identify() and claims the nexus0 device if the probe succeeds. It
then explicitly adds an acpi0 device in its attach routine.
- The legacy(4) driver no longer knows anything about the acpi0 device.
- On ia64 if acpi_identify() fails you basically end up with no devices.
This matches the previous behavior where the old acpi_identify() would
fail to add an acpi0 device again leaving you with no devices.
Discussed with: imp
Silence on: arch@
of directly from acpi0. Before it would attach prior to the sysresource
devices, causing the later allocation of its memory range to fail and
print a warning like "acpi0: reservation of fed00000, 1000 (3) failed".
Use an explicit define for our probe order base value of 10.
Help from: jhb
Tested by: Abdullah Ibn Hamad Al-Marri <almarrie / gmail.com>
MFC after: 3 days
Approved by: re
Improvements:
* /etc/rc.suspend,rc.resume are always run, no matter the source of the
suspend request (user or kernel, apm or acpi)
* suspend now requires positive user acknowledgement. If a user program
wants to cancel the suspend, they can. If one of the user programs
hangs or doesn't respond within 10 seconds, the system suspends anyway.
* /dev/apm is clonable, allowing multiple listeners for suspend events.
In the future, xorg-server can use this to be informed about suspend
even if there are other listeners (i.e. apmd).
Changes:
* Two new ACPI ioctls: REQSLPSTATE and ACKSLPSTATE. Request begins the
process of suspending by notifying all listeners. acpi is monitored by
devd(8) and /dev/apm listener(s) are also counted. Users register their
approval or disapproval via Ack. If anyone disapproves, suspend is vetoed.
* Old user programs or kernel modules that used SETSLPSTATE continue to
work. A message is printed once that this interface is deprecated.
* acpiconf gains the -k flag to ack the suspend request. This flag is
undocumented on purpose since it's only used by /etc/rc.suspend. It is
not intended to be a permanent change and will be removed once a better
power API is implemented.
* S5 (power off) is no longer supported via acpiconf -s 5 or apm -z/-Z.
This restores previous behavior of halt/shutdown -p being the interface.
* Miscellaneous improvements to error reporting
Approved by: re
modern dual-core systems as well.
- Parse the _CST packages for each cpu and track all the states individually,
on a per-cpu basis.
- Revert to generic FADT/P_BLK based Cx control if the _CST package
is not present on all cpus. In that case, the new driver will
still support per-cpu Cx state handling. The driver will determine the
highest Cx level that can be supported by all the cpus and configure the
available Cx state based on that.
- Fixed the case where multiple cpus in the system share the same
registers for Cx state handling. To do that, added a new flag
parameter to the acpi_PkgGas and acpi_bus_alloc_gas functions that
enable the caller to add the RF_SHAREABLE flag. This flag could also be
useful to other callers (acpi_throttle?) in the tree but this change is
not yet made.
- For Core Duo cpus, both cores seems to be taken out of C3 state when
any one of the cores need to transition out. This broke the short sleep
detection logic. It is disabled now if there is more than one cpu in
the system for now as it fixed it in my case. This quirk may need to
be re-enabled later differently.
- Added support to control cx_lowest on a per-cpu basis. There is still
a generic cx_lowest to enable changing cx_lowest for all cpus with a single
sysctl and for ease of use. Sample output for the new sysctl:
dev.cpu.0.cx_supported: C1/1 C2/1 C3/57
dev.cpu.0.cx_lowest: C3
dev.cpu.0.cx_usage: 0.00% 43.16% 56.83%
dev.cpu.1.cx_supported: C1/1 C2/1 C3/57
dev.cpu.1.cx_lowest: C3
dev.cpu.1.cx_usage: 0.00% 45.65% 54.34%
hw.acpi.cpu.cx_lowest: C3
This work was done by Stephane E. Potvin with some simple reworking by
myself. Thank you.
Submitted by: Stephane E. Potvin <sepotvin / videotron.ca>
MFC after: 2 weeks
perform the reboot action via the reset register instead of our legacy
method. Default is 0 (use legacy). This is needed because some systems
hang on reboot even though they claim to support the reset register.
MFC after: 2 days
(i.e., smart battery) and fix various bugs found during the cleanup.
API changes:
* kernel access:
Access to individual batteries is now via devclass_find("battery").
Introduce new methods ACPI_BATT_GET_STATUS (for _BST-formatted data) and
ACPI_BATT_GET_INFO (for _BIF-formatted data). The helper function
acpi_battery_get_battinfo() now takes a device_t instead of a unit #
argument. If dev is NULL, this signifies all batteries.
* ioctl access:
The ACPIIO_BATT_GET_TYPE and ACPIIO_BATT_GET_BATTDESC ioctls have been
removed. Since there is now no need for a mapping between "virtual" unit
and physical unit, usermode programs can just specify the unit directly and
skip the old translation steps. In fact, acpiconf(8) was actually already
doing this and virtual unit was the same as physical unit in all cases
since there was previously only one battery type (acpi_cmbat). Additionally,
we now map the ACPIIO_BATT_GET_BIF and ACPIIO_BATT_GET_BST ioctls for all
batteries, if they provide the associated methods.
* apm compatibility device/ioctls: no change
* sysctl: no change
Since most third-party applications use the apm(4) compat interface, there
should be very few affected applications (if any).
Reviewed by: bruno
MFC after: 5 days
of swi. This allows us to use the taskqueue_thread_* functions instead of
rolling our own. It also avoids a double trip through the queue.
Submitted by: njl
Reviewed by: sam
number of task threads to start on boot. Go back to a default of 3
threads to work around lost battery state problems. Users that need
a setting of 1 can set this via the tunable. I am investigating the
underlying issues and this tunable can be removed once they are solved.
MFC after: 2 days
to see what features they may support before calling identify/probe/attach.
This is necessary because the ACPI 3.0 spec requires driver support be
advertised before running any methods. For now, the flags are as specified
in for the _PDC and _OSC methods but we can support private flags as needed.
Add an implementation of this for acpi_cpu. It checks all its children
(notably cpufreq drivers) and calls the _PDC method to report the results.
may help with various interdependencies between subsystems. More testing
is needed to understand what the underlying issues are here.
Tested by: Juho Vuori
MFC after: 2 days
IRQ 0 and not an ExtINT pin. The MADT enumerators ignore the PC-AT flag
and ignore overrides that map IRQ 0 to pin 2 when this quirk is present.
- Add a block comment above the quirks to document each quirk so that we
can use more verbose descriptions quirks.
MFC after: 2 weeks
type. This is needed if the resource is to be released later. The RID is
still also present, though less necessary since rman_get_rid() can be used
to obtain it from the resource.
with acpi but the timer runs twice as fast. Note that the main problem
(system doesn't work properly with acpi disabled) should be fixed separately.
Changes:
* Add a quirk to disable the timer
* Merge the P5A and P5A-B quirks since they appear to be based on the
same ASL.
PR: i386/72450
Tested by: Kevin Oberman <oberman es.net>
MFC after: 3 days
hold its own values, pass them up to the parent (acpi0) and merge/uniq them
on the way. After the namespace evaluation, acpi will reserve these
resources and manage them via rman before bus_generic_probe() and
bus_generic_attach(). This is necessary because some systems specify
conflicting resources in separate sysresource objects. It's also cleaner
in that the interface between sysresource and acpi is now merely the parent's
resource list. This code handles the following cases:
1. Unique resource: add it to the parent via bus_set_resource().
2. New wholly contained in old: discard new.
3. New tail overlaps old head: grow old head downward.
AND/OR
4. New head overlaps old tail: grow old tail upward.
Tested by: Pawel Worach <sajd_at_telia.com>
Tested by: Radek Kozlowski <radek_at_raadradd.com>
MFC after: 5 days
callers. These ioctls attempted to enable and disable the ACPI
interpreter at runtime. In practice, it is not possible to boot with
ACPI and then disable it on many systems and trying to do so can cause
crashes, interrupt storms, etc. Binary compatibility with userland is
retained.
MFC after: 2 days
* Add and comment our locking primitives. The mutex primitives use a
a static mutex and the serialization ones use a static sx lock. A global
acpi_mutex is used for access to global resources (i.e., writes to the
SMI_CMD register.)
* Remove 4.x compat defines.
Unify the code to disable GPEs with the enable code. Shutdown is handled
the same way. ACPI now does all wake/sleep prep for child devices so
now they no longer need to call external functions in the suspend/resume
path. Add the flags to non-ACPI busses (i.e., pci).
