command. This fixes some weird booting issues on newer versions
of the firmware on the MSA20.
Reported by: Philippe Pegon <Philippe dot Pegon at crc dot u-strasbg dot fr>
- Give up endianess support and switch to native-endian format for
accessing hardware structures. In fact embedded processor for
BCM57xx is big-endian architure(MIPS) and it requires native-endian
format for NIC structures.The NIC performs necessary byte/word
swapping depending on programmed endian type.
- With above changes all htole16/htole32 calls were gone.
- Remove bge_vhandle member in softc and changed to use explicit
register access. This may add additional performance penalty
that than that of previous memory access. But most of the access
is performed on initialization phase(e.g. RCB setup), it would be
negligible.
Due to incorrect use of bus_dma(9) in bge(4) it still panics sparc64
system in device detach path. The issue would be fixed in next patch.
Reviewed by: jkim (initial version)
Silence from: ps
Tested by: glebius
Obtained from: NetBSD via OpenBSD
1. Implement a large set of ioctl shims so that the Linux management apps
from LSI will work. This includes infrastructure to support adding, deleting
and rescanning arrays at runtime. This is based on work from Doug Ambrosko,
heavily augmented by LSI and Yahoo.
2. Implement full 64-bit DMA support. Systems with more than 4GB of RAM
can now operate without the cost of bounce buffers. Cards that cannot do
64-bit DMA will automatically revert to using bounce buffers. This option
can be forced off by setting the 'hw.amr.force_sg32" tunable in the loader.
It should only be turned off for debugging purposes. This work was sponsored
by Yahoo.
3. Streamline the command delivery and interrupt handler paths after
much discussion with Dell and LSI. The logic now closely matches the
intended design, making it both more robust and much faster. Certain
i/o failures under heavy load should be fixed with this.
4. Optimize the locking. In the interrupt handler, the card can be checked
for completed commands without any locks held, due to the handler being
implicitely serialized and there being no need to look at any shared data.
Only grab the lock to return the command structure to the free pool. A
small optimization can still be made to collect all of the completions
together and then free them together under a single lock.
Items 3 and 4 significantly increase the performance of the driver. On an
LSI 320-2X card, transactions per second went from 13,000 to 31,000 in my
testing with these changes. However, these changes are still fairly
experimental and shouldn't be merged to 6.x until there is more testing.
Thanks to Doug Ambrosko, LSI, Dell, and Yahoo for contributing towards
this.
to use busdma. Unlike most of the other drivers, but similar to the
if_em driver, pre-allocate the dmamaps at init time instead of allocating
them on the fly when descriptors need to be filled. This isn't ideal right
now because a map is allocated for every descriptor slot in the tx, rx, mini,
and jumbo rings (which is a lot!) in order to simplify the bookkeeping, even
though the driver might support filling only a subset of those slots.
Luckily, maps are typically NULL on i386 and amd64, so the cost isn't
very high. It could be an issue with sparc64, but the driver isn't endian
clean either, and that is a much bigger problem to solve first.
Note that jumbo frame support is under-tested, and I'm not even sure if
it till really works correctly given the evil VM magic that is does.
The changes here attempt to preserve the existing semanitcs.
Thanks to Martin Nillson for contributing the Netgear card for this work.
MFC-After: 3 weeks
compilation of kernels without ns8250 support but using the uart framework.
These kernels will be for machines where size matters more, so including code
that can never be executed is undesriable...
working at all and only saw "nve0: device timeout (N)" messages.
- Setup PHY before handing control to NVidia API setting
speed, duplex, enabling interrupts, etc.
- Add restriction of MAXADDR_32BIT for high address to contigmalloc
to make the driver work on machines with 4+GB of memory.
PR: kern/85583, kern/88045
Tested by: scottl, others earlier version
MFC after: 10 days
transmitted bits was between 8.6180us and 8.6200us when we used a RCLK
of 16.500MHz. This is a little low (should be 8.6805us). This error
is exactly the error one would expect if it actually had a 16.384MHz
watch oscillator (as suggested by garrett) instead of using the PCI
RCLK. Assume that the pci clock therefore wasn't really used, but
instead the cheap 16.384MH watch quartz oscillator. This gives bits
in the 8.6800us to 8.6810us ranage, which matches theoretical.
Submitted by: garrett
cluster allocator, that wasn't MPSAFE. Instead, utilize our new generic
UMA jumbo cluster allocator. Since UMA gives us a 9k piece that is contigous
in virtual memory, but isn't contigous in physical memory we need to handle
a few segments. To deal with this we utilize Tigon chip feature - extended
RX descriptors, that can handle up to four DMA segments for one frame.
Details:
o Remove bge_alloc_jumbo_mem(), bge_free_jumbo_mem(),
bge_jalloc(), bge_jfree() functions.
o Remove SLIST heads, bge_jumbo_tag, bge_jumbo_map from softc.
o Use extended RX BDs for Jumbo receive producer ring, and
initialize it appropriately.
o New bge_newbuf_jumbo():
- Allocate an mbuf with Jumbo cluster with help of m_cljget().
- Load the cluster for DMA with help of bus_dmamap_load_mbuf_sg().
- Assert that we got 3 segments in the DMA mapping.
- Fill in these 3 segments into the extended RX descriptor.
2) rework link state detection code & use it in POLLING mode
3) fix 2 bugs in link state detection code:
a) driver unable to detect link loss on bcm5721
b) on bcm570x chips (tested on bcm5700 bcm5701 bcm5702) driver fails
to detect link loss with probability 1/6 (solved in brgphy.c)
Devices working in TBI mode should not be affected by this change.
Approved by: glebius (mentor)
MFC after: 1 month
"done" method so that for non-repeat operations we have completely
finished with the transfer by the time the callback is invoked.
This makes it possible to recycle a transfer from within the callback
routine for the same transfer. Previously this almost worked, but
with OHCI controllers calling the "done" method after the callback
would zero out some important fields needed by the recycled transfer.
Only some usb peripheral drivers such as ucom appear to rely on the
ability to reuse a transfer from its callback.
MFC after: 1 week
time ago appears to be based not on the typical 1.8432MHz clock, or
the other more typical multiple of 8 of this (14.7456MHz), but instead
it appears to be 1/2 the PCI clock rate or 16.50000MHz. I'm not 100%
sure that this is right, but since I did the original entry, I'm going
to go ahead and modify it. With the 14.7456MHz value, I was getting
bits that were ~7.3us instead of ~8.6us like they are supposed to be.
My measuring gear for today is a stupid handheld scope with two
signficant digits. So I don't know if it is 33.000000/2 MHz or some
other value close to 16.5MHz, but 16.5MHz works well enough for me to
use a couple of different devices at 115200 baud, and is a nice even
multiple of a well known clock frequency...
acquired anywhere in the driver now.
- Axe the spin mutex used for the nve_oslock*() routines. The driver lock
already provides sufficient synchronization.
- Don't mess around with IFF_UP when the link state changes. IFF_UP is
an administrative flag, not a link status indicator.
MFC after: 1 week
immediately from acpi_pci_link_route_interrupt() since we aren't going
to have a valid pci_link device to talk to try to route interrupts. This
fixes a page fault if you disable just pci_link. Note that trying to use
ACPI without pci_link is probably not advised however.
MFC after: 1 week
Tested by: Eugene Grosbein eugen at kuzbass dot ru
the eaddr array (introduced in rev. 1.174) prior to writing to it. As
dc_read_eeprom() is told to write only 3 16-bit words to eaddr but eaddr
in fact is somewhat larger removal of the zeroing defeated the check
whether the MAC address is all zero as there can be some random garbage
in eaddr past the 3 words written to it and the check verifys all bits
in eaddr. Solve this by changing the check to verify only the 3 words
(happenning to be ETHER_ADDR_LEN bytes) written to eaddr.
- While here change the notation of "FCode" in a nearby comment to the
official way.
Ok'ed by: marcel, ru
polarity. Some machines route PCI IRQs to an ISA IRQ but fail to include
an interrupt override entry to set the polarity and trigger of the given
ISA IRQ in their MADT table.
PR: usb/74989
Reported by: Julien Gabel jpeg at thilelli dot net
MFC after: 1 week
and some fixes from Motomichi Matsuzaki. Testing involved many people, but the
final, successful testing was from rwatson who endured several rounds of "it
crashes at XYZ stage" "oh, please correct this typo and try again." The Linux
driver, and to a small extent the limited specs, were both used as a reference
for how to program the chipset.
PR: kern/80396
Submitted by: Martin Mersberger
Update Intel MatrixRAID support to be able to pick up RAID0+1 (RAID10)
and RAID5 arrays without panic'ing.
This has the side effect of now also supporting multiple volumes on
MatrixRAID's now I have the metadata better understood..
HW sponsored by: Mullet Scandinavia AB
commit. Copy the ethernet address into a local buffer, which we know
is sufficiently aligned for the width of the memory accesses that we
do. This also eliminates all suspicious and potentionally harmful
casts.
In collaboration with: ru
- S3 Savage driver ported.
- Added support for ATI_fragment_shader registers for r200.
- Improved r300 support, needed for latest r300 DRI driver.
- (possibly) r300 PCIE support, needs X.Org server from CVS.
- Added support for PCI Matrox cards.
- Software fallbacks fixed for Rage 128, which used to render badly or hang.
- Some issues reported by WITNESS are fixed.
- i915 module Makefile added, as the driver may now be working, but is untested.
- Added scripts for copying and preprocessing DRM CVS for inclusion in the
kernel. Thanks to Daniel Stone for getting me started on that.
appeared to rely on all kinds of non-guaranteed behaviours: the
transfer abort code assumed that TDs with no interrupt timeout
configured would end up on the done queue within 20ms, the done
queue processing assumed that all TDs from a transfer would appear
at the same time, and there were access-after-free bugs triggered
on failed transfers.
Attempt to fix these problems by the following changes:
- Use a maximum (6-frame) interrupt delay instead of no interrupt
delay to ensure that the 20ms wait in ohci_abort_xfer() is enough
for the TDs to have been taken off the hardware done queue.
- Defer cancellation of timeouts and freeing of TDs until we either
hit an error or reach the final TD.
- Remove TDs from the done queue before freeing them so that it
is safe to continue traversing the done queue.
This appears to fix a hang that was reproducable with revision 1.67
or 1.68 of ulpt.c (earlier revisions had a different transfer
pattern). With certain HP printers, the command "true > /dev/ulpt0"
would cause ohci_add_done() to spin because the done queue had a
loop. The list corruption was caused by a 3-TD transfer where the
first TD completed but remained on the internal host controller
done queue because it had no interrupt timeout. When the transfer
timed out, the TD got freed and reused, so it caused a loop in the
done queue when it was inserted a second time from a different
transfer.
Reported by: Alex Pivovarov
MFC after: 1 week
This shouldn't happen as far as the self-id buffer is vaild but
some people have this problem.
PR: kern/83999
Submitted by: Markus Wild <fbsd-lists@dudes.ch>
MFC after: 3 days
- Add locked variants of start, init, and ifmedia_upd.
- Add a mutex to the softc and remove spl calls.
- Use callout(9) rather than timeout(9).
- Setup interrupt handler last in attach.
- Use M_ZERO rather than bzero.
MFC after: 1 week
Tested by: wpaul
- Improve panic message if we fail to read the PCI bus number from a bridge
device.
- Don't try to lookup a BIOS IRQ for a link unless the link is routed via
an ISA IRQ since BIOSen currently only route PCI link devices via ISA
IRQs.
Tested by: Mathieu Prevot bsdhack at club-internet dot fr
MFC after: 1 week
Instead, re-evaluate _BIF only when we get a notify and use the cached
results. We also still evaluate _BIF once on boot. Also, optimize the
init loop a little by only querying for a particular info if it's not valid.
MFC after: 2 days
a newly introduced struct ofw_bus_devinfo which can hold the OFW info
of a device recallable via the ofw_bus KOBJ interface. Introduce a set
of functions ofw_bus_gen_get_*() which use ofw_bus_default_get_devinfo()
to provide generic subroutines for implementing the rest of the ofw_bus
KOBJ interface in a bus driver.
This is inspired by bus_get_resource_list() and bus_generic_rl_*_resource()
and allows to reduce code duplication in bus drivers as they only have
to provide an ofw_bus_default_get_devinfo() implementation in order to
provide the ofw_bus KOBJ interface via ofw_bus_gen_get_*().
- While here add a comment to ofw_bus_if.m describing the intention of
the ofw_bus KOBJ interface.
Reviewed by: marcel
the tree.
- Add locked variants of nve_start(), nve_init(), and nve_ifmedia_upd().
- Use callout_* to manage callouts rather than timeout(9).
- Mark interrupt handler MPSAFE (IFF_NEEDGIANT was already clear).
- Lock the driver lock in driver entry points such as the interrupt
handler, if_start, and if_init rather than locking the driver mutex
in the various work functions called by the binary blob. The spin lock
used by the binary block can probably be stubbed out now.
- Use IFQ_DRV_IS_EMPTY() macro rather than doing it by hand.
- Fix locking in detach.
- Remove some unused fields from the softc.
Tested by: cognet
MFC after: 2 weeks
the IRQ set by the BIOS in existing devices to actually get the correct
bus number of the child PCI bus. I was not reading the bus number from
the bridge device correctly. The __BUS_ACCESSOR() macros (from which
pcib_get_bus() is built) assume that the passed in argument is a child
device. However, at the time I'm reading the bus there is no child
device yet, so I was passing in the pcib device as the child device.
The parent of the pcib device probably returned an error in the case of
a host bridge, thus resulting in random stack garbage for the bus number.
For PCI-PCI bridges, the bus number being used was actually the subvendor
of the PCI-PCI bridge device itself.
MFC after: 1 week
- Don't call tulip_addr_filter() to reset the RX address filter in
tulip_reset() since that gets called before ether_ifattach(). Just
call it in tulip_init_locked().
- Use be16dec() and le16dec() to parse MAC addresses when programming
the RX filter.
- Let ether_ioctl() handle SIOCSIFMTU since we were doing the exact same
thing with the added bonus that we leaked the driver lock if the MTU
was > ETHERMTU in the homerolled version. This part will be MFC'd.
Clue from: wpaul (1)
Stolen from: marcel (2 via patch for dc(4))
MFC after: 1 week
via the DEFAULTS kernel configs. This allows folks to turn it that option
off in the kernel configs if desired without having to hack the source.
This is especially useful since PUC_FASTINTR hangs the kernel boot on my
ultra60 which has two uart(4) devices hung off of a puc(4) device.
I did not enable PUC_FASTINTR by default on powerpc since powerpc does not
currently allow sharing of INTR_FAST with non-INTR_FAST like the other
archs.
buildkernel: provide a real but dummy name to ${DEPENDFILE}
so that the relevant exists() check in bsd.prog.mk fails and
ensures that ${GENHDRS} are built before any other objects.
MFC after: 3 days
- don't force busdma to pre-allocate bounce pages for parent tag.
- use system supplied roundup2 macro instead of rolling its own version.
- TX/RX decriptor length should be multiple of 128. There is no
no need to expand the size with the multiple of 4096.
- don't create/destroy DMA maps in TX/RX handlers. Use pre-allocated
DMA maps. Since creating DMA maps on sparc64 is time consuming
operations(resource mananger overhead), this change should boost
performance on sparc64. I could get > 2x speedup on Ultra60.
- TX/RX descriptors could be aligned on 128 boundary. Aligning them
on PAGE_SIZE is waste of resource.
- don't blindly create TX DMA tag with size of MCLBYTES * 8. The size
is only valid under jumbo frame environments. Instead of using the
hardcoded value, re-compute necessary size on the fly.
- RX side bus_dmamap_load_mbuf_sg(9) support.
- remove unused macro EM_ROUNDUP and constant EM_MMBA.
Reviewed by: scottl
Tested by: glebius
that enabling busmastering would result in PCR bit ON after codec
reset.
While I'm here add DELAY(1) to codec access routine to give reasonable
time to codec operation. Without the delay, it would cause problems on
super-fast machines(> 2GHz). Also enable legacy audio for all 6300ESB,
82801[D-G]B chips. Previously, it enabled legacy audio for 82801DB(ICH4)
chip only.
Reported by: Maxim Maximov mcsi AT mcsi DOT pp DOT ru
Andrew Bliznak andriko.b AT gmail DOT com
Tested by: brueffer, Maxim Maximov, Andrew Bliznak
directory by default) without requiring the user to load them by hand using
e.g iwicontrol. Get rid of the old ioctl crud.
Updated iwi-firmware port coming soon.
Obtained from: OpenBSD
for a notebook with em(4) adapter.
- Introduce tunables em.hw.txd and em.hw.rxd, which allow administrator
to configure number of transmit and receive descriptors.
- Check em.hw.txd and em.hw.rxd against hardware limits [*] and require
them to be multiple of 128.
[*] According to comments in if_em.h the 82540EM/82541ER chips can handle
more than 256 descriptors. Since we don't have this hardware to test,
we decided to mimic NetBSD wm(4) driver, that limits these chips to
256 descriptors.
In collaboration with: yongari
stale when called to reset rate control state causing us to
pickup an invalid index, check for this and skip 'em (things
will eventually get fixed up so this is not harmful)
of volumes that might need administrator attention through device
specific sysctl to simplify device monitoring.
Submitted by: Deomid Ryabkov <myself at rojer dot pp dot ru>
This one simply tries to simplify the logic to select the
buffer sizes. I am not sure it is necessary but the code
seems a bit more readable to me. And at least i have tried
to document how the buffer sizes are computed.
Thanks to luigi for deciphering one of the most cryptic part of
sound driver.
Submitted by: luigi
Approved by: netchild (mentor)
In SNDCTL_DSP_SETFRAGMENT, if you specify both read and
write channels, the existing code first acts on the
read channel, but as a side effect it updates the
arguments (maxfrags, fragsz) passed by the caller according
to acceptable values for the read channel, and then uses the
modified values to act on the write channel.
The problem with this approach is that, given a
(maxfrags, fragsz) user-specified value, the actual
values computed by the read and write channels may differ:
e.g. the read channel might want to allocate more fragments
than what the user specified because it has no side-effects
on the delay and it helps in case of slow readers,
whereas the write channel needs to use as few fragments
as possible to keep the audio latency low (very important
with telephony apps).
This patch stores the values computed by the read channel
into temproary variables so the write channel will use
the actual arguments of the ioctl.
This patch is very helpful with telephony apps such as asterisk.
Submitted by: luigi
Approved by: netchild (mentor)
- Added new codec id for CX20468-21 and VIA1617A.
Submitted by: Chen Lihong <lihong.chen@gmail.com>
- Re-enable SOUND_MIXER_IGAIN, but set the default level as 0 (mute)
Suggested by: luigi
mixer.c:
- Set default value for SOUND_MIXER_IGAIN as 0 (mute) to avoid
feedback problems on some laptops (was disabled by jhb during
ac97.c revision 1.42).
Approved by: netchild (mentor)
erratic system slowdown (beaten to a pulp) and possible panic. This
issue has bugged me for as long as I could remember, until I
realized that it is possible for register base offset to hold zero
value which is definitely a "FALSE".
Approved by: netchild (mentor)
compatible AC97 codec.
- As the driver supports so many variants, create a table ids for
ease of probing and maintenance.
Submitted by: yongari
Reviewed/Tested by: multimedia@
- From luigi:
The code to compute fragment sizes in the ich driver almost
invariably ends up using the full buffer available, no matter
how the user specifies fragment size and number.
With audio telephony (8khz, 16bit-stereo) and the 16k buffer
size this results in an unbearable 500ms delay.
This patch makes sure that we never use more than 4 fragments,
(i don't think we need more unless there are huge interrupt
servicing latencies), and obey to the requested fragment size,
so that latency is acceptable.
Based on this (and after much regression tests), I can conclude
that this driver works best with 2 fragments, thus solving various
long standing issues of ICH driver not capable to flush or play
short files perfectly.
Suggested by: luigi (the idea of smaller fragments)
- MPSAFE conversion.
Approved by: netchild (mentor)
distinct hardware playback channels. DAC configuration can be
accessed through kernel hint - hint.pcm.<unit>.dac="val" with
following possible values:
0 = Enable both DACs (default)
1 = Enable single DAC (DAC1)
2 = Enable single DAC (DAC2)
3 = Enable both DACs, swap position (DAC2 comes first instead
of DAC1)
Special case for ES1370:
Unlike ES1371,2,3/CT5880, volume for each DAC 1 and 2 can be
controlled indepedently (synth for DAC1, pcm for DAC2). It is
possible that user will confuse by this behaviour, since both
DACs are enabled by default. Thus, provide a knob through sysctl
hw.snd.pcm<unit>.single_pcm_mixer:
0 = each DACs will be controlled separately (synth/pcm).
1 = combine both DACs volume mixer controller into a single
"pcm" (default)
As a side note, fixed rate operation (provided by previous
commit) is not a mandatory if the configuration space does not
involve DAC2 (perhaps disabled by user through the above kernel
hint). Unlike DAC2, DAC1 has its own register / control space,
not affected by the speed settings of ADC.
Tested by: multimedia@
Approved by: netchild (mentor)
mask to recdev_l and recdev_r, since each have its own unique mask.
Submitted by: Watanabe Kazuhiro <CQG00620@nifty.ne.jp>
Approved by: netchild (mentor)
just discard the received frame and reuse the old mbuf.
This should prevent the connection from stalling after high network traffic.
MFC after: 2 weeks
a new mbuf, just discard the received frame and reuse the old mbuf.
This should fix kernel panics on high network traffic.
Obtained from: NetBSD (joerg@)
MFC after: 2 weeks
It may be the case that you may hear some unwanted noise while
playing back with 24/32 bit. This is a problem in the USB system.
Explanation from Hans Petter Selasky:
---snip---
The current USB sound driver only uses one isochronous
buffer, that is restarted when it is completed. This will lead to a short
period of time, +1ms, where no sound data is sent to the external USB device.
Depending on the load of your computer, this can be as much as 50ms. So the
USB sound driver must use 2 isochronous transfers. At the beginning one will
queue both. Then these are restarted on completion. This will result in a
constant-rate data stream to the external sound device, a minimum sound
buffer equal to the size of the isochronous buffer, and possibly the sound
will reach your ears with less delay. Little delay is a result of constant
data rate. Currently only my USB driver will support that. If one tries that
with the USB driver in *BSD, then it will crash at the first moment one gets
a buffer underrun.
---snip---
Submitted by: Kazuhito HONDA <kazuhito@ph.noda.tus.ac.jp>
Mono-recording still not tested by: julian
- several TerraTec TValue [1]
- PixelView PlayTV Pro REV-4C [2]
In case you have the PixelView card, please tell us the "pciconf -v -l"
output on multimedia@FreeBSD.org if it works. There are revisions out there
which may not work and we need to know which ones work.
PR: 53383 [1], 76002 [2]
Submitted by: Tanja Wittke <tawi@gruft.de> [1], barner [1],
Dan Angelescu <mrhsaacdoh@yahoo.com> [2]
MFC after: 2 months
This is the only file of > 1700 files in a buildkernel here doing that.
It makes reproducible builds (same source => same binary) impossible.
Spotted by: devel/ccache
from the printer and discarding the data even if the ulpt device
was opened for reading. This resulted in crashes because two
conconcurrent read transfers were using the same transfer structure.
PR: usb/88886
Reported By: Alex Pivovarov
MFC after: 1 week
rather than in ifindex_table[]; all (except one) accesses are
through ifp anyway. IF_LLADDR() works faster, and all (except
one) ifaddr_byindex() users were converted to use ifp->if_addr.
- Stop storing a (pointer to) Ethernet address in "struct arpcom",
and drop the IFP2ENADDR() macro; all users have been converted
to use IF_LLADDR() instead.
The following repo-copies were made (by Mark Murray):
sys/i386/isa/spkr.c -> sys/dev/speaker/spkr.c
sys/i386/include/speaker.h -> sys/dev/speaker/speaker.h
share/man/man4/man4.i386/spkr.4 -> share/man/man4/spkr.4
copy of Ethernet address.
- Change iso88025_ifattach() and fddi_ifattach() to accept MAC
address as an argument, similar to ether_ifattach(), to make
this work.
overruns and number of watchdog timeouts.
- Do not log(9) RX overrun events, since this pessimizes
things under load [1].
- Do not increase if->if_oerrors in em_watchdog(), since
this leads to counter slipping back, when if->if_oerrors
is recalculated in em_update_stats_counters(). Instead
increase watchdog counter in em_watchdog() and take it
into account in em_update_stats_counters().
Submitted by: ade [1]
- disable jumbo frame support on strict alignment architectures due
to the limitation of hardware. The driver needs a fix-up code for
RX side. The fix will show up in near future.
- fix endian issue for 82544 on PCI-X bus. I couldn't test this as
I don't have the NIC/hardware.
- prefer PCIR_BAR to hardcoded EM_MMBA.
- Properly checks for for 64bit BAR [1]
- replace inl/outl with bus_space(9) [1]
- fix endian issue on VLAN handling.
- reorder header files and remove unnecessary one.
Reviewed by: cognet
No response from: pdeuskar, tackerman
Obtained from: OpenBSD [1]
the RocketPort unit number in the name of the devices. This means that
unit 0 device names will change from ttyR0 .. ttyRf to ttyR00 .. ttyR0f.
Reviewed by: phk
acpi_resource change was a minor nit offered as an early candidate for
the recent ACPICA import problem and the acpi.c change is one I need to
test still that makes the ordered probing of system devices actually work
as advertised (probe devices in order based on the type of device rather
than in the order we encounter them in the device tree).
entry that is not zero, assume that it is really a hard-wired IRQ (commonly
used for APIC routing) and not a source index. In practice, we've only
ever seen source indices of 0 for legitimate non-hard-wired _PRT entries.
Reviewed by: njl
Tested by: Alex Lyashkov shadow at psoft dot net
MFC after: 2 weeks
Intel's web site requires some minor tweaks to get it to work:
- The driver seems to have been released with full WMI tracing enabled,
and makes references to some WMI APIs, namely IoWMIRegistrationControl(),
WmiQueryTraceInformation() and WmiTraceMessage(). Only the first
one is ever called (during intialization). These have been implemented
as do-nothing stubs for now. Also added a definition for STATUS_NOT_FOUND
to ntoskrnl_var.h, which is used as a return code for one of the WMI
routines.
- The driver references KeRaiseIrqlToDpcLevel() and KeLowerIrql()
(the latter as a function, which is unusual because normally
KeLowerIrql() is a macro in the Windows DDK that calls KfLowewIrql()).
I'm not sure why these are being called since they're not really
part of WDM. Presumeably they're being used for backwards
compatibility with old versions of Windows. These have been
implemented in subr_hal.c. (Note that they're _stdcall routines
instead of _fastcall.)
- When querying the OID_802_11_BSSID_LIST OID to get a BSSID list,
you don't know ahead of time how many networks the NIC has found
during scanning, so you're allowed to pass 0 as the list length.
This should cause the driver to return an 'insufficient resources'
error and set the length to indicate how many bytes are actually
needed. However for some reason, the Intel driver does not honor
this convention: if you give it a length of 0, it returns some
other error and doesn't tell you how much space is really needed.
To get around this, if using a length of 0 yields anything besides
the expected error case, we arbitrarily assume a length of 64K.
This is similar to the hack that wpa_supplicant uses when doing
a BSSID list query.
for code to start out on one CPU when thunking into Windows
mode in ctxsw_utow(), and then be pre-empted and migrated to another
CPU before thunking back to UNIX mode in ctxsw_wtou(). This is
bad, because then we can end up looking at the wrong 'thread environment
block' when trying to come back to UNIX mode. To avoid this, we now
pin ourselves to the current CPU when thunking into Windows code.
Few other cleanups, since I'm here:
- Get rid of the ndis_isr(), ndis_enable_interrupt() and
ndis_disable_interrupt() wrappers from kern_ndis.c and just invoke
the miniport's methods directly in the interrupt handling routines
in subr_ndis.c. We may as well lose the function call overhead,
since we don't need to export these things outside of ndis.ko
now anyway.
- Remove call to ndis_enable_interrupt() from ndis_init() in if_ndis.c.
We don't need to do it there anyway (the miniport init routine handles
it, if needed).
- Fix the logic in NdisWriteErrorLogEntry() a little.
- Change some NDIS_STATUS_xxx codes in subr_ntoskrnl.c into STATUS_xxx
codes.
- Handle kthread_create() failure correctly in PsCreateSystemThread().
since the link takes a bit to negotiate, the information is pretty
much never available during the probe. As such, the boot output
pretty much always prints N/A for speed and duplex. Since we print
out the output of ifconfig during the user space boot, this early
boot information is also generally redundant, and added to the noise.
MFC after: 2 weeks
- Prefer '_' to ' ', as it results in more easily parsed results in
memory monitoring tools such as vmstat.
- Remove punctuation that is incompatible with using memory type names
as file names, such as '/' characters.
- Disambiguate some collisions by adding subsystem prefixes to some
memory types.
- Generally prefer lower case to upper case.
- If the same type is defined in multiple architecture directories,
attempt to use the same name in additional cases.
Not all instances were caught in this change, so more work is required to
finish this conversion. Similar changes are required for UMA zone names.
in bytes to start off with. This caused the GPT geom sniffer to attempt
a seek just back from the end of the 'disk', which resulted in a > 4G
seek, causing gdb psim to exit since it only supports 32-bit seeks.
The size of the disk should really be specified in the psim device tree,
but for now do the minimal amount of work to get psim to run again.
aac_alloc_sync_fib(). aac_alloc_sync_fib() will assert that the I/O locks
are held. This fixes a panic on system boot up when the aac(4) device's
bus_generic_attach() routine is called.
Reviewed by: scottl
- Return EINVAL if play_format or rec_format is set but the corresponding
sample rate is 0.
- Don't try to set the playback or recording format to 0. Previously,
issuing an AIOSFMT ioctl with an all-zeroes snd_chan_param would
trigger a KASSERT in chn_fmtchain(); I'm unsure about the effects on
a kernel without INVARIANTS. After this commit, issuing AIOSFMT with
an all-zeroes snd_chan_param is equivalent to issuing AIOGFMT.
MFC after: 2 weeks
actual resource values we received from the system rather than the range
we requested. Since we request a range starting at 0, we would record
that number. Later, since this == 0, we'd allocate again. However,
we wouldn't write the new resource into the BAR. This resulted in
a resource leak as well as a BAR that couldn't access the resource at
all since rman_get_start, et al, were wrong.
MFC After: 1 week (assuming RELENG_6 is open for business)
the ifp, so you can't call it before doing if_alloc(). Also, there's
really no need to call it here anyway: the code I originally ported from
OpenBSD incorrectly set the station address only once at device attach
time, instead of setting in txp_init(). This meant you couldn't change
the address with ifconfig txp0 ether xx:xx:xx:xx:xx:xx. I added the
call to txp_set_filter() in txp_init() to correct this, but forgot to
remove the call from txp_attach(). Until now, it never mattered.
With this fix, the txp driver tests good:
txp0: <3Com 3cR990-TX-97 Etherlink with 3XP Processor> port 0xb800-0xb87f mem 0xe6800000-0xe683ffff irq 12 at device 10.0 on pci0
txp0: Ethernet address: 00:01:03:d4:91:4f
and channel to ifconfig. Also use the SSID and channel info from
the association info that we already have instead of using ndis_get_info()
to ask the driver for it again.
