tested on Intel BX chipsets only. The other agp minidrivers are totally
untested.
The programming api is a subset of the Linux api and is only intended to
be enough for the X server to use. There is also an in-kernel api for the
use of other kernel modules such as the 3D DRI.
21143 chips, I accidentally removed the DC_MII_REDUCED_POLL flag
for all 21143 cards. This caused problems with timer-instigated
TCP retransmits, which happened to occur at the same time as an
MII poll tick on MII-based cards (e.g. D-Link DFE-570TX). Fixed this,
plus made some other cleanups. The autoneg fixes for the non-MII
cards still work. Also tested the PNIC II now that I have one again.
Fix several instances of breakage in RAID-5 revive code.
Tidy up code.
parityops:
Don't attempt to do anything if the plex is degraded or worse.
parityrebuild:
Add comments.
Perform transfers in correct length.
after autoneg so we make sure to set the link state and duplex mode
correctly.
- Make sure to set the 'ignore pause frames' bit on the XMAC.
- Small linewrap fix.
needed to add into ether_input) and finally sorting IFF_RUNNING through
whole driver.
As part of the IFF_RUNNING stuff, we've added an extra flag so callers
can request that runq routines should check IFF_RUNNING before executing.
Remove BPF taps as this is now done by ether_input.
Resurrect multicast code, moving the multicast list stuff to the runq
routine.
Dump ray_promisc_user as all flag changes are now handled by ray_init, and
add a couple of checks to ray_promisc.
In uppparams_user, allow changes before the card is running (need to
fix some breakage with _download here later). In addition, don't
assume that the current n/w parameters are valid - they are only valid
in the runq.
Fix a nasty flag bug - runq_add cleared all the flags on the last command!
Remove the hacks for setting the memory flags - problems were down
to buggy versions of pccardd. For some reason pccardd only dtrt with
the "right" debug_level.
not gone yet.
format_config: print correct text when a volume has a preferred plex.
This is still broken, but not quite as badly.
Reported-by: Phil Regnauld <regnauld@ftf.net>
Change a rather silly comment.
routines from foo_watchdog() because foo_watchdog() is called at
interrupt context, and that's a no-no due to the way the USB stack
is currently set up.
What we do now is call the TX end of frame handler manually to clear
the completed transmission, then check the send queue and send off
any frames that are pending.
Also turned off the interrupt pipe stuff in if_aue, since it appears
to tickle a bug in the USB stack that I haven't found yet.
motherboards that use YMF740's. It has a strange subvendor and subdevice
ID and requires a disturbingly long delay after the ac97 codec init.
Cameron hasn't had this driver tested on another 740 yet, so we don't know
if this is a quirk of all 740's, or if its just something about the codec
that Intel used.
workalike chips (Macronix 98713A/98715 and PNIC II). Timing is somewhat
critical: you need to bring the link as soon as possible after NWAY
is done, and the old one second polling interval was too long. Now
we poll every 10th of a second until NWAY completes (at which point
we return to the 1 second interval again to keep an eye on the link
state).
I tested all the other cards I had on hand to make sure I didn't bust
any of them and they seem to work (including the MII-based 21143 card).
This should fix some autoneg problems with DE500-BA cards and the
built-in 10/100 ethernet on some alpha systems.
(Now before anyone asks why I never noticed this before, the old code
worked just find with the Intel swich I used for testing back in NY.
Apparently not all switches are as picky about the timing.)
It may cause misterious chars appearse in the middle of the scrolled lines.
The bug trigger: enter
grep P_32 /usr/include/*.h
command and see misterious "db.\" filename.
