other architectures [1].
While here:
- Remove an unused and commented out include.
- Add a comment describing the file that other copies have.
- Fix the style of the defines and add a comment on what each one is.
Suggested by: [1] alc
sent a SIGABRT when it is loaded as it is too large. This is the smallest
power of two MiB value that allows us to execute clang.
While here wrap it in an #ifndef to be consistent with the other
architectures.
Submitted by: Daisuke Aoyama <aoyama at peach.ne.jp>
Switch eventtimers(9) from using struct bintime to sbintime_t.
Even before this not a single driver really supported full dynamic range of
struct bintime even in theory, not speaking about practical inexpediency.
This change legitimates the status quo and cleans up the code.
Although AM335x TRM states that GPIO_OE register is not used and just
reflects pads configuration in practice it does control pin behavior
and shoiuld be set in addition to pinmux setup
Replace the sub-optimal uma_zone_set_obj() primitive with more modern
uma_zone_reserve_kva(). The new primitive reserves before hand
the necessary KVA space to cater the zone allocations and allocates pages
with ALLOC_NOOBJ. More specifically:
- uma_zone_reserve_kva() does not need an object to cater the backend
allocator.
- uma_zone_reserve_kva() can cater M_WAITOK requests, in order to
serve zones which need to do uma_prealloc() too.
- When possible, uma_zone_reserve_kva() uses directly the direct-mapping
by uma_small_alloc() rather than relying on the KVA / offset
combination.
The removal of the object attribute allows 2 further changes:
1) _vm_object_allocate() becomes static within vm_object.c
2) VM_OBJECT_LOCK_INIT() is removed. This function is replaced by
direct calls to mtx_init() as there is no need to export it anymore
and the calls aren't either homogeneous anymore: there are now small
differences between arguments passed to mtx_init().
Sponsored by: EMC / Isilon storage division
Reviewed by: alc (which also offered almost all the comments)
Tested by: pho, jhb, davide
fact, use the same values here that we use on 32-bit x86 and MIPS. Some
machines were reported to have problems with the more aggressive values.
Reported and tested by: andrew
thread scheduled by interrupt fired after we entered critical section.
None of cpu_sleep() implementations on ARM check sched_runnable() now, so
put the first line of defence here. This mostly fixes unexpectedly long
sleeps in synthetic tests of calloutng code and probably other situations.
* VM_OBJECT_LOCK and VM_OBJECT_UNLOCK are mapped to write operations
* VM_OBJECT_SLEEP() is introduced as a general purpose primitve to
get a sleep operation using a VM_OBJECT_LOCK() as protection
* The approach must bear with vm_pager.h namespace pollution so many
files require including directly rwlock.h
seems to cause more problems then previous behavior: it either breaks
initilization sequence in other places or uncovers problems with
high-speed mode timing for SDHCI 3.0
Fix pull-up and pull-down values of gpio.
According to A10 user manual possible pull register
values are 00 Pull-up/down disable, 01 Pull-up, 10 Pull-down.
Approved by: gonzo@
submap. Otherwise, after r246204, the auto-scaling logic in kern_malloc.c
tries to create a kmem submap that consumes the entire kernel map on a
Pandaboard with 1 GB of RAM.
Tested by: gonzo
machine to another. Therefore, VM_MAX_KERNEL_ADDRESS can't be a constant.
Instead, #define it to be a variable, vm_max_kernel_address, just like we
do on sparc64.
Reviewed by: kib
Tested by: ian
SDHCI driver
Suggested by: Daisuke Aoyama
- Set initilization sequence frequency to 8MHz. It should fix Data CRC
errors. Standard requires initialization sequence to be executed
at 400KHz but on this hardware low frequncies seems to cause
Data CRC errors.
Value was derived from analyzing hardware signals after
Raspberry Pi is powered up. Before any data is read though DATA line
adapter's clock frequency is changed to 8MHz.
Modern cards should function fine at 8MHz but for older MMC cards it
can be overriden by setting hw.bcm2835.sdhci.min_freq tunable.
every architecture's busdma_machdep.c. It is done by unifying the
bus_dmamap_load_buffer() routines so that they may be called from MI
code. The MD busdma is then given a chance to do any final processing
in the complete() callback.
The cam changes unify the bus_dmamap_load* handling in cam drivers.
The arm and mips implementations are updated to track virtual
addresses for sync(). Previously this was done in a type specific
way. Now it is done in a generic way by recording the list of
virtuals in the map.
Submitted by: jeff (sponsored by EMC/Isilon)
Reviewed by: kan (previous version), scottl,
mjacob (isp(4), no objections for target mode changes)
Discussed with: ian (arm changes)
Tested by: marius (sparc64), mips (jmallet), isci(4) on x86 (jharris),
amd64 (Fabian Keil <freebsd-listen@fabiankeil.de>)
