- Bring HEAD up to the latest shared code
- Fix TSO problem using limited MSS and forwarding
- Dual lock implementation
- New device support
- For my ease, this code can compile in either 6.x or later
- brings this driver in sync with the 6.3
prepend a data mbuf in front of a header mbuf without moving the header
to the new mbuf, and (2) a possible alignment problem on architectures
with strict alignment as reported in kern/4184.
PR: kern/4184 (1)
addresses as the source of an AARP request. While this PR was submitted
in the context of work in OpenBSD to port netatalk (in 1997), I've
synchronized the code more to our ARP input routine, which had similar
requirements.
Submitted by: Denton Gentry
PR: kern/4184
MFC after: 1 week
only at address 0 which is supposed to be the only valid phy address
on Marvell PHY. The more correct solution would be masking PHY
address ranges allowable in PHY probe routine. Unfortunately,
FreeBSD has no way to retrict the PHY address ranges or to pass special
flags to PHY driver.
This change assumes that PHY hardwares attached to msk(4) would be
Marvell made 88E11xx PHY.
With this changes the phantom phys attached on 88E8036(Yukon FE)
should disappear.
Reported by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
Tested by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
only 4KB SRAM.
o Rework setting Tx/Rx RAM buffer size. Give receiver 2/3 of memory
and round it down to the multiple of 1024. The RAM buffer size of
Yukon II should be multiple of 1024. This fixes bogus RAM buffer
configuration used in Yukon FE.
Reported by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
Tested by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
timestamps in the initial SYN packet actually use them in the rest of the
connection. Unfortunately, during the 7.0 testing cycle users have already
found network devices that violate this constraint.
RFC 1323 states 'and may send a TSopt in other segments' rather than
'and MUST send', so we must allow it.
Discovered by: Rob Zietlow
Tracked down by: Kip Macy
PR: bin/118005
publicly available datasheet for Yukon II and don't know what
bug/workaround exist for the specific hardware revision. Also I don't
think the vendor will release hardware errata in near future.
The hardware feature lists were not used at all except setting water
mark registers. Since msk(4) should know exact chip model/revision
number to decide which hardware capability could be used the extra
feature lists were redundant.
o Enable jumbo frame support for EC Ultra and disable jumbo frame
for FE.
o Enable store and forward mode for standard MTU sized frame.
o Enable TSO for EC Ultra. However TSO/checksum offload is disabled
for jumbo frame case. Because EC Ultra can't use store and forward
mode for jumbo frame TSO/checksum offload is not available.
o Adjust Tx GMAC almost empty threshold value and add a jumbo frame
water mark. The maic value was obtained from Marvell's sk98lin
driver.
o Fix EC Ultra chip revision number.
rwlocks in conjuction with callouts. The function does basically what
callout_init_mtx() alredy does with the difference of using a rwlock
as extra argument.
CALLOUT_SHAREDLOCK flag can be used, now, in order to acquire the lock only
in read mode when running the callout handler. It has no effects when used
in conjuction with mtx.
In order to implement this, underlying callout functions have been made
completely lock type-unaware, so accordingly with this, sysctl
debug.to_avg_mtxcalls is now changed in the generic
debug.to_avg_lockcalls.
Note: currently the allowed lock classes are mutexes and rwlocks because
callout handlers run in softclock swi, so they cannot sleep and they
cannot acquire sleepable locks like sx or lockmgr.
Requested by: kmacy, pjd, rwatson
Reviewed by: jhb
Revert the probe in atapi-cd.c to the old usage now its fixed on AHCI.
THis change also fixes using virtual CD's om fx parallels.
Still leaves the GEOM problem of telling media vs device access apart in the access function.
server-side RPC retranmission cache for non-idempotent operations: these
hacks substituted 0 (success) for the expected EEXIST in the event that
a target name already existed for LINK, SYMLINK, and MKDIR operations,
under the assumption that EEXIST represented a second application of the
original RPC rather than a true failure.
Background: certain NFS operations (in this case, LINK, SYMLINK, and
MKDIR) are not idempotent, as they leave behind persisting state on the
server that prevents them from being replayed without an error;if an UDP
RPC reply is lost leading to a retransmission by theclient, the second
reply will return EEXIST rather than success, asthe new object has
already been created. The NFS client previouslysilently mapped the
EEXIST return into success to paper over thisproblem.
However, in all modern NFS server implementations, a reply cache is kept
in order to retransmit the original reply to a retransmitted request,
rather than performing the operation a second time, allowing this hack
to be avoided. This allows link()-based filelocking over NFS to operate
correctly, as an application requestingthe creation of a new link for a
file to tell if it succeededatomically or not.
Other NFS clients, including Solaris and Linux, generally follow this
behavior for the same reasons. Most clients also now default to TCP,
which also helps avoid the issue of retransmitted but non-idempotent
requests in most cases.
Reported by: Adam McDougall <mcdouga9 at egr dot msu dot edu>,
Timo Sirainen <tss at iki dot fi>
Reviewed by: mohans
MFC after: 1 week
o buffered write, for chunks smaller than PIPE_MINDIRECT bytes
o direct write, for everything else
A call to writev(2) may receive struct iov of various size and the
kernel may have to switch from one solution to the other. Before doing
this, it must wake reader processes and any select/poll/kqueue up.
This commit fixes a bug where select/poll/kqueue are not triggered
when switching from buffered write to direct write. It adds calls to
pipeselwakeup().
I give more details on freebsd-arch@:
http://lists.freebsd.org/pipermail/freebsd-arch/2007-September/006790.html
This should fix issues with Erlang (lang/erlang) and kqueue.
Reported by: Rickard Green (Erlang)
time ago (2002 according to the gcc log). Using the proper name
fixes a warning in src/lib/libc/gen/ulimit.c about the second
argument of va_start() not being the last named (when it really
was).
This has the following benefits:
- allows to use the AT keyboard maps in share/syscons/keymaps with
sunkbd(4),
- allows to use kbdmux(4) with sunkbd(4),
- allows Sun RS232 keyboards to be configured and used the same
way as Sun USB keyboards driven by ukbd(4) (which also does AT
keyboard emulation) with X.Org, putting an end to the problem
of native support for the former in X.Org being broken over and
over again.
MFC after: 3 days
an unified way for all the lock primitives to express lock assertions.
Currenty, lockmgrs and rmlocks don't have assertions, so just panic in
that case.
This will be a base for more callout improvements.
Ok'ed by: jhb, jeff
strees2 suite, to quote his letter, this change:
1. It removes the tn_lookup_dirent stuff. I think this cannot be fixed,
because nothing protects vnode/tmpfs node between lookup is done, and
actual operation is performed, in the case the vnode lock is dropped.
At least, this is the case with the from vnode for rename.
For now, we do the linear lookup in the parent node. This has its own
drawbacks. Not mentioning speed (that could be fixed by using hash), the
real problem is the situation where several hardlinks exist in the dvp.
But, I think this is fixable.
2. The patch restores the VV_ROOT flag on the root vnode after it became
reclaimed and allocated again. This fixes MPASS assertion at the start
of the tmpfs_lookup() reported by many.
Submitted by: kib
First, a file is mmap(2)ed and then mlock(2)ed. Later, it is truncated.
Under "normal" circumstances, i.e., when the file is not mlock(2)ed, the
pages beyond the EOF are unmapped and freed. However, when the file is
mlock(2)ed, the pages beyond the EOF are unmapped but not freed because
they have a non-zero wire count. This can be a mistake. Specifically,
it is a mistake if the sole reason why the pages are wired is because of
wired, managed mappings. Previously, unmapping the pages destroys these
wired, managed mappings, but does not reduce the pages' wire count.
Consequently, when the file is unmapped, the pages are not unwired
because the wired mapping has been destroyed. Moreover, when the vm
object is finally destroyed, the pages are leaked because they are still
wired. The fix is to reduce the pages' wired count by the number of
wired, managed mappings destroyed. To do this, I introduce a new pmap
function pmap_page_wired_mappings() that returns the number of managed
mappings to the given physical page that are wired, and I use this
function in vm_object_page_remove().
Reviewed by: tegge
MFC after: 6 weeks
If it is set to zero value (default) dummynet module will try to emulate
real link as close as possible (bandwidth & latency): packet will not leave
pipe faster than it should be on real link with given bandwidth.
(This is original behaviour of dummynet which was altered in previous commit)
If it is set to non-zero value only bandwidth is enforced: packet's latency
can be lower comparing to real link with given bandwidth.
- Document recently introduced dummynet(4) sysctl variables.
Requested by: luigi, julian
MFC after: 3 month
with ACCESSPERMS. Document in mount_ntfs(8) only the nine
low-order bits of mask are used (taken from mount_msdosfs(8)).
PR: kern/114856
Submitted by: Ighighi
MFC after: 1 month
In case attach fails because of the priv check we leaked the
memory and left so_pcb as fodder for invariants.
Reported by: Pawel Worach
Reviewed by: rwatson
- Implement timing out of VPD register access.[1]
- Fix an off-by-one error of freeing malloc'd space when checksum is invalid.
- Fix style(9) bugs, i.e., sizeof cannot be followed by space.
- Retire now obsolete 'hw.pci.enable_vpd' tunable.
Submitted by: cokane (initial revision)[1]
Reviewed by: marius (intermediate revision)
Silence from: jhb, jmg, rwatson
Tested by: cokane, jkim
MFC after: 3 days
The register layout is little different from memory-mapped stats
in the previous generation chips. In fact, it is bad because
registers in this range are cleared after reading them.
Reviewed by: scottl
MFC after: 3 days
- Trying to eliminate another racing by replacing the timeout(9) with
callout APIs. In addition to that, the callout_drain() in an_detach()
help us to avoid a possible panic-on-free due to the callout API tries
to lock a destroyed mutex.
- In an_stats_update(), check the return value of an_read_record(). This
should reduce the chance of device removal(PCCARD) panic [2].
- Adding a comment to state the fact that an_stats_update() is now called
via callout(9) with a lock held [2].
Submitted by: jhb [1], ambrisko [2]
Reviewed by: jhb, ambrisko
Reported by: dhw
Tested by: dhw
MFC after: 3 days
priorities of the technologies supported by 802.3 Selector Field
value.
1000BASE-T full duplex
1000BASE-T
100BASE-T2 full duplex
100BASE-TX full duplex
100BASE-T2
100BASE-T4
100BASE-TX
10BASE-T full duplex
10BAST-T
However PHY drivers didn't honor the order such that 100BASE-T4 had
higher priority than 100BASE-TX full duplex. Fix that long standing
bugs such that have PHY drivers choose the highest common denominator
ability.
Fix a bug in dcphy which inadvertently aceepts 100BASE-T4.
PR: 92599
