This change is needed because 'opt_rss.h' is included by multiple source
files and RSS macro is defined as 1 within the file during build process
if option RSS is enabled in the kernel.
Submitted by: Ivan Malov <Ivan.Malov at oktetlabs.ru>
Reviewed by: gnn
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D6718
And fix message processing; only channel messages are supported.
MFC after: 1 week
Sponsored by: Microsoft OSTC
Differential Revision: https://reviews.freebsd.org/D6706
makeman doesn't handle this since it would need to enable all
non-default options when checking enabling 1 option, which
then convolutes what is really affecting each other.
This fixes build failures on older releases that lack various
definitions such as EM_AARCH64 (which was unfixed before this).
Revert all of the recent compatibility changes that worked around this
problem.
This uses the same method of using the in-tree header as lib/libelf,
lib/libdwarf and usr.bin/readelf.
Reviewed by: emaste
Sponsored by: EMC / Isilon Storage Division
Differential Revision: https://reviews.freebsd.org/D6734
This is actually a revision in the stable/9 branch released as 9.1. The
localedef build requires xlocale from this period.
Sponsored by: EMC / Isilon Storage Division
CCACHE_DIR needs to be resolved to its full path before processing
legacy.meta or meta mode may see the change to the stats file.
Sponsored by: EMC / Isilon Storage Division
The WITH_META_MODE build is intended to be a working incremental build.
It spies on the build command to see if things should be rebuilt if the
command changes. If you run buildworld, it builds a cross-compiler,
then do installworld and buildworld again it will invoke the
WITH_SYSTEM_COMPILER logic. This then adds on -target/--sysroot, etc,
and causes rebuilds due to the changed build command even though the
compiler used is technically the same revision. Since the incremental
build is not cleaning anything by default then there is much
less risk to rebuilding the already-existing cross-compiler. Just
disable the combined logic and always use and build the cross-compiler.
An alternative to this would be to always pass -target/--sysroot. Doing
so may occur in the future.
Sponsored by: EMC / Isilon Storage Division
Using buildworld, installworld, buildworld. It is expected that nothing
should rebuild. However any host tool used could have its timestamp
updated. Any library used by dynamic tools could have its timestamp
updated. The filemon(4) data in the .meta files captures all reads to
these files. This causes the 2nd buildworld to rebuild everything since
host tools and files have been updated.
Because the build is self-reliant and bootstraps itself, it should be
safe to ignore mtime changes on host files used during the build. Host
files should only impact the build of legacy, build-tools, bootstrap-tools,
cross-tools, but those are already intended to be reproducible from its
own bootstrapping. It is possible in a rare case that a bug in a host
file does produce a broken build tool. If that happens it will just
have to be communicated properly.
An alternative solution would be to update the mtime of all files in the
object directory after installworld so that the host files are not newer
than the object files. That also requires special care for read-only
obj directories and special care to not mess with any intended timestamps in
the build, such as done for reproducibility.
Reported by: many
Sponsored by: EMC / Isilon Storage Division
When collation support was brought in, the second and third
arguments in __collate_range_cmp() were changed from int to
wchar_t, breaking the ABI. Change them to a "char" type which
makes more sense and keeps the ABI compatible.
Also introduce __wcollate_range_cmp() which does work with wide
characters. This function is used only internally in libc so
we don't export it. Use the new function in glob(3), fnmatch(3),
and regexec(3).
PR: 179721
Suggested by: ache. jilles
MFC after: 3 weeks (perhaps partial only)
This is a NOP.
The COMPAT_IA32 was renamed in r205014 to COMPAT_FREEBSD32 and
COMPAT_ARCH32 does not seem to have existed. Also remove some
leftovers from the sysent rework in r301404. Include
freebsd32_util.h for the freebsd32_sysent prototype.
X-MFC-With: r301404
Reported by: kib
MFC after: 3 days
Sponsored by: EMC / Isilon Storage Division
Do not try to change attributes for DMAP when working on a mapping
which is not covered by the DMAP. This was reported on real system
where a BAR of a device (NTB) was mapped outside the PCI window.
Reported and tested by: mav
Reviewed by: jhb, mav
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D6668
p_sched is unused.
The struct td_sched is always co-allocated with the struct thread,
except for the thread0. Avoid useless indirection, instead calculate
td_sched location using simple pointer arithmetic in td_get_sched(9).
For thread0, which is statically allocated, create a structure to
emulate layout of the dynamic allocation.
Reviewed by: jhb (previous version)
Sponsored by: The FreeBSD Foundation
Differential revision: https://reviews.freebsd.org/D6711
BUS_MAP_INTR() is used to get an interrupt mapping data according
to provided hints. The hints could be modified afterwards, but only
if mapping data was allocated. This method is intended to be called
before BUS_ALLOC_RESOURCE().
An interrupt mapping data describes an interrupt - hardware number,
type, configuration, cpu binding, and whatever is needed to setup it.
(2) Introduce a method which allows storing of an additional data
in struct resource to be available for bus drivers. This method is
convenient in two ways:
- there is no need to rework existing bus drivers as they can simply
be extended to provide an additional data,
- there is no need to modify any existing bus methods as struct
resource is already passed to them as argument and thus stored data
is simply accessible by other bus drivers.
For now, implement this method only for INTRNG.
This is motivated by needs of modern SOCs where hardware initialization
is not straightforward and resources descriptions are complex, opaque
for everyone but provider, and may vary from SOC to SOC. Typical
situation is that one bus driver can fetch a resource description for
its child device, but it's opaque for this driver. Another bus driver
knows a provider for this kind of resource and can pass this resource
description to it. In fact, something like device IVARS would be
perfect for that if implemented generally enough. Unfortunatelly, IVARS
are usable only by their owners now. Only owner knows its IVARS layout,
thus other bus drivers are not able to use them.
Differential Revision: https://reviews.freebsd.org/D6632
This trips me up whenever I'm fooling around with partially supported
NICs that fail to fully attach or initialise - the firmware gets loaded
and references, but something fails - and the firmware references
aren't cleaned up.
After perusing the PHY-LP code (don't ask why; honest) I discovered that
it /has/ 5GHz support - but it's not ever used. I found one NIC - a
BCM4312 w/ pci id 0x4315 - which advertised dual-band PHY-LP support.
Turns out it works.
Whilst here, move up the support bit logging code so I can use it
to debug this.
Tested:
* BCM4312 (pci id 0x4315); 5GHz STA operation
On Medford, licenses are required to enable RX and event cut through and to
disable RX batching. To avoid the need for the driver to make decisions based on
the licensing state, the MC_CMD_INIT_EVQ has been extended to allow us to leave
the decision to the firmware. If the adapter is licensed for low-latency use,
the firmware will choose the optimal settings for latency, otherwise it will use
the best settings for throughput.
For Huntington we still need to choose the settings ourselves.
Submitted by: Mark Spender <mspender at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D6717
This seems to make 5G work better.
It doesn't fix powersave handling though, that still sees the PHY get
stuck during initial calibration and everything goes pear shaped.
I'll look into that later.
Tested:
* QCAFN222 NIC, STA mode, 5GHz
Obtained from: Linux ath9k
Turns out I wasn't even initialising or programming a lot of stuff
for the AR9462 2.1 chip. Oops.
This mostly gets it working. powersave scan results in some pretty
hilarious NFcal hangs and I don't see beacons reliably.
There are still some xlna gain tables missing that ath9k has; I'll
follow up with some fixes and then see if the QCAFN222 NIC I have
tests this path.
Tested:
* QCAFN222 NIC, STA mode, 2GHz and 5GHz
the graphics drivers can benefit from access to the lid handle for querying and getting notifications
Submitted by: kmacy
Differential Revision: https://reviews.freebsd.org/D6643
