containing an Ethernet address fitted as this is yet another thing
that fails in that case in order to avoid the one second delay
until pci_read_vpd_reg() times out.
- Const'ify the bge_devs array.
when it runs on half-duplex media.
While I'm here add register definition for GPREG1. ATM the GPREG1
register is only valid for JMC250 A1/A2.
Submitted by: Ethan at JMicron
o don't use the key index to identify when the driver has been
asked to allocate a key slot, use an explicit flag; allows
drivers to force s/w fallback for entries in the global table
o change callback api to allocate driver resources for a crypto key:
- de-const the key parameter so drivers can muck with the flags
- on callback failure don't automatically try to setup s/w crypto;
instead the driver must now mark the key entry for s/w crypto and
the caller will re-attach the cipher module
NB: api change permits drivers more control over fallback to s/w
crypto (e.g. based on a limited number of h/w key slots)
to vga_pci.c to request on behalf of it's children. This causes vgapci to show
up as the interrupt owner in vmstat -i, rather than the child device.
Approved by: jhb(mentor)
kib@ and I have decided we will MFC the bpf(4)/snp(4) fixes after we've
released 7.1. Make sure the code in HEAD doesn't refer to a flag we
don't need anyway.
snp(4) in the MPSAFE TTY P4 branch already works, but still needs some
polishing before it can be integrated to SVN.
this also can be happened if we pull the USN stick out forcibly.
Currently the ZyDAS driver uses tsleep() when it try to query a read
command to the device and it'd make a timeout if the device doesn't
response within about 1 sec.
In a case of that the USB stick is gone by hand and the driver's
scanning with changing the channel numbers, the thread which is sleeping
until a command requested is responded can be waked up after all
detaching routines finished that means the zyd softc already freed.
Tring to touch the softc freed by the wakeup thread makes a panic.
So make sure that all sleeping threads should be waken up before the
detach is completed and any other new requests to the device should be
prevented.
years by the priv_check(9) interface and just very few places are left.
Note that compatibility stub with older FreeBSD version
(all above the 8 limit though) are left in order to reduce diffs against
old versions. It is responsibility of the maintainers for any module, if
they think it is the case, to axe out such cases.
This patch breaks KPI so __FreeBSD_version will be bumped into a later
commit.
This patch needs to be credited 50-50 with rwatson@ as he found time to
explain me how the priv_check() works in detail and to review patches.
Tested by: Giovanni Trematerra <giovanni dot trematerra at gmail dot com>
Reviewed by: rwatson
Left only parts surely required for basic troubleshooting and configuration
purposes. There is still very long output, but further shrinking makes it
less informative.
Original debugging can be enabled with hw.snd.verbose=4.
the command set (only so long as the module is present):
o add db_command_register and db_command_unregister to add and remove
commands, respectively
o replace linker sets with SYSINIT's (and SYSUINIT's) that register
commands
o expose 3 list heads: db_cmd_table, db_show_table, and db_show_all_table
for registering top-level commands, show operands, and show all operands,
respectively
While here also:
o sort command lists
o add DB_ALIAS, DB_SHOW_ALIAS, and DB_SHOW_ALL_ALIAS to add aliases
for existing commands
o add "show all trace" as an alias for "show alltrace"
o add "show all locks" as an alias for "show alllocks"
Submitted by: Guillaume Ballet <gballet@gmail.com> (original version)
Reviewed by: jhb
MFC after: 1 month
- Retire IVARs for passing IRQs around. Instead, ppbus and ppc now allow
child devices to access the interrupt by via a rid 0 IRQ resource
using bus_alloc_resource_any().
- ppc creates its own interrupt event to manage the interrupt handlers of
child devices. ppc does not allow child devices to use filters. It
could allow this if needed, but none of the current drivers use them
and it adds a good bit of complication. It uses
intr_event_execute_handlers() to fire the child device interrupt handlers
from its threaded interrupt handler.
- Remove the ppbus_dummy_intr() hack. Now the ppc device always has an
interrupt handler registered and we no longer bounce all the way up to
nexus to manage adding/removing ppbus child interrupt handlers. Instead,
the child handlers are added and removed to the private interrupt event
in the ppc device.
On the i386 architecture, the processor only saves the current value
of `%esp' on stack if a privilege switch is necessary when entering
the interrupt handler. Thus, `frame->tf_esp' is only valid for
an entry from user mode. For interrupts taken in kernel mode, we
need to determine the top-of-stack for the interrupted kernel
procedure by adding the appropriate offset to the current frame
pointer.
Reported by: kris, Fabien Thomas
Tested by: Fabien Thomas <fabien.thomas at netasq dot com>
Because of using more clear and same time more functional codec parser
new driver is able to handle more codecs, use them better then before and
without most of previous quirks. All of tested codecs itself manage playback,
record, input mixing and monitoring quite fine. In all of investigated
trouble cases problem was found or in nonstandard codec usage or incorrect
codec configuration made by BIOS. Most of that cases could be fixed using
device hints, some of which are already included to the driver.
New driver supports multiple codecs per HDA bus, multiple audio function
groups per codec and multiple logical sound devices per audio function group.
So don't worry when you get several PCM devices instead of one, it is normal.
It is usual situation with powerful codecs to provide, for example, 3 PCM
devices: one for 7.1 playback and main recording, one for headset and one
for digital SPDIF I/O.
New driver implements Universal Audio Architecture (UAA) much better then
previous one. Most information about recommended codec usage now taken from
the codec configuration registers initialized by BIOS. User may alter that
configuration using device hints to reconfigure logical audio devices to
his needs in a very broad range up to the limits of the codec functionality.
New driver supports digital PCM playback and AC3 pass-through. I am not sure
about completeness of this implementation, but I have several success stories
including my own. Vchans subsystem does not support AC3 pass-through so it
had to be disabled for that devices at this moment.
New driver is ready for multichannel playback, but until our OSS is unable
to use this it will just duplicate same stereo stream into all channel
pairs.
New driver supports suspend/resume. I am unable to really test this part
myself, but I have got several success stories.
Driver has very informative verbose boot messages. So if you have any
questions or problems - enable and read them first.
Discussed on: freebsd-multimedia@
Tested by: many
- When searching for the next system drive, return the next one instead
of always returning the first one.
- Plug fd lead and make sure that the MLX_NEXT_CHILD ioctl is called
on the controller fd, not the disk's one.
While there, fix a cut-n-pase error in a warning.
Reviewed by: jhb
Approved by: kan (mentor)
MFC after: 1 month
detaching that when the USB is pulled out forcibly during the driver is
running background scan, a page fault can be occurred even if we called
usb_rem_task() when detaching. It looks like a kind of races.
be un-cached. Our previous memory barrier was not sufficient. This patch
allocates the IGP GART tables using the BUS_DMA_NOCACHE flag to get these
cards working.
Approved by: kib
calls to bus_dma. There were multiple paths that held different locks or
no locks at all. This patch ensures that all of the calling paths drop
their lock(s) before calling drm_pci_alloc().
Reviewed by: kib
