Unfortunately there are two slight problems with that:
- Yacc and lex might generate code that generates warnings because of
this. Require yacc and lex to be rebuilt during bootstrap. I'm not
incrementing __FreeBSD_version here, because I assume someone else
will do this eventually.
- When running `make buildkernel', it uses share/mk from the source
treeo to build aicasm. Because aicasm also depends on lex, this would
break. Lower WARNS to 5 for now. We should just increment it to 6
again somewhere in the very far future.
stored in a BAR since the CIS BAR is mapped before the PCI bus driver
enumerates all the BARs. Without this change, the PCI bus driver would
attempt to initialize a BAR that was already allocated resulting in a panic.
handling for the PCIR_BIOS decoding enable bit from the cardbus driver.
The PCIR_BIOS BAR does include type bits like other BARs. Instead, it is
always a 32-bit non-prefetchable memory BAR where the low bit is used as a
flag to enable decoding.
Reviewed by: imp
This replaces d_mmap() with the d_mmap2() implementation and also
changes the type of offset to vm_ooffset_t.
Purge d_mmap2().
All driver modules will need to be rebuilt since D_VERSION is also
bumped.
Reviewed by: jhb@
MFC after: Not in this lifetime...
get required command protocol. But they have no idea about new commands,
such as DATA SET MANAGEMENT (TRIM). As soon as this info any way provided
by CAM, give controller specific instructions.
* new firmware
* untested support for 1000 and 6000 series
* bgscan support
* remove unnecessary RXON changes
* allow setting of country/regdomain by enforcing channel flags read
from the EEPROM
* suspend/resume fixes
* RF kill switch fixes
* LED adjustments
* several bus_dma*() related fixes
* addressed some LORs
* many other bug fixes
Submitted by: Bernhard Schmidt <bschmidt at techwires.net>
Obtained from: Brandon Gooch <jamesbrandongooch at gmail dot com> (LED
related changes), Benjamin Kaduk <kaduk at mit dot edu>
(LOR fixes), OpenBSD
Fix some wrong usages.
Note: this does not affect generated binaries as this argument is not used.
PR: 137213
Submitted by: Eygene Ryabinkin (initial version)
MFC after: 1 month
blkif interface in Xen requires all I/O to be 512 byte aligned with each
segment bounded by a 4k page.
Note: This submission only documents the proper contraints for blkif I/O.
The alignment code in busdma does not yet handle alignment constraints
correctly in all cases.
* Correct a group of typos: for Core2 programmable events, check
user supplied umask values against the correct event descriptor
field.
Submitted by: Ryan Stone <rysto32 at gmail dot com>
Unlike TX interrupt, ST201 does not provide any mechanism to
suppress RX interrupts. ste(4) can generate more than 70k RX
interrupts under heavy RX traffics such that these excessive
interrupts make system useless to process other useful things.
Maybe this was the major reason why polling support code was
introduced to ste(4).
The STE_COUNTDOWN register provides a programmable counter that
will generate an interrupt upon its expiration. We program
STE_DMACTL register to use 3.2us clock rate to drive the counter
register. Whenever ste(4) serves RX interrupt, the driver rearm
the timer to expire after STE_IM_RX_TIMER_DEFAULT time and disables
further generation of RX interrupts. This trick seems to work well
and ste(4) generates less than 8k RX interrupts even under 64 bytes
UDP torture test. Combined with TX interrupts, the total number of
interrupts are less than 10k which looks reasonable on heavily
loaded controller.
The default RX interrupt moderation time is 150us. Users can change
the value at any time with dev.ste.%d.int_rx_mod sysctl node.
Setting it 0 effectively disables the RX interrupt moderation
feature. Now we have both TX/RX interrupt moderation code so remove
loop of interrupt handler which resulted in sub-optimal performance
as well as more register accesses.
This brings hwpmc(4) support for 2nd and 3rd generation XScale cores.
Right now it's enabled by default to make sure we test this a bit.
When the time comes it can be disabled by default.
Tested on Gateworks boards.
A man page is coming.
Obtained from: //depot/user/rpaulo/xscalepmc/...
transmitted frames. So request interrupt for every 16th frames. Due
to the limitation of hardware we can't suppress the interrupt as
driver should have to check TX status register. The TX status
register can store up to 31 TX status so driver can't send more
than 31 frames without reading TX status register.
With this change controller would not generate TX completion
interrupt for every frame, so reclaim transmitted frames in
ste_tick().
used to return success without respect to the result.
While I'm here use mii_mediachg() in ste_init_locked which allows
driver to use currently configured media. ste_ifmedia_upd() is
supposed to be called whenever user changes current media settings.
o Let RX filter handler program promiscuous/multicast filter as
well as broadcasting.
o Remove unnecessary register access.
o Simplify ioctl handler and have set_rxfilter to handle
IFF_PROMISC and IFF_ALLMULTI change instead of directly
programming the controller.
o Removed unnecessary error variable reinitialization in ioctl
handler.
o Add IFF_DRV_RUNNING check before programming multicast filter.
o Configure maximum allowed frame length before enabling MAC.
Datasheet didn't say the exact ordering of programming sequence
but it looks more natural to set maximum allowed frame length
first prior to enabling controller.
1ms. Since we switched to memory register mapping make sure to
flush PCI posted write by reading the register again.
While I'm here add additional delays in loop while driver waits the
completion of the reset.
If ste(4) encounter TX underrun or excessive collisions the TX MAC
of controller is stalled so driver should wake it up again. TX
underrun requires increasing TX threshold value to minimize
further TX underruns. Previously ste(4) used to reset controller
to recover from TX underrun, excessive collision and reclaiming
error. However datasheet says only TX underrun requires resetting
entire controller. So implement ste_restart_tx() that restarts TX
MAC and do not perform full reset except TX underrun case.
Now ste(4) uses CSR_READ_2 instead of CSR_READ_1 to read
STE_TX_STATUS register. This way ste(4) will also read frame id
value and we can write the same value back to STE_TX_FRAMEID
register instead of overwriting it to 0. The datasheet was wrong
in write back of STE_TX_STATUS so add some comments why we do so.
Also always invoke ste_txeoc() after ste_txeof() in ste_poll as
without reading TX status register can stall TX MAC.
