octeon_ap_boot is not a bitmask. It holds the CPU Id of the
AP currently being started. As such there's no need to make
it a 64-bit integral and we're not limited to 64 CPUs.
Reported by: jmallet
Obtained from: Andre Duane
Add some improvements in the idle table callbacks:
- Replace instances of manual assembly instruction "hlt" call
with halt() function calling.
- In cpu_idle_mwait() avoid races in check to sched_runnable() using
the same pattern used in cpu_idle_hlt() with the 'hlt' instruction.
- Add comments explaining the logic behind the pattern used in
cpu_idle_hlt() and other idle callbacks.
Pre-11n devices and AR5416 use AR_PHY(263) for current RX RSSI.
AR9130 and later have a fourth calibration register (for doing
ADC calibration) and thus the register has moved to AR_PHY(271).
This isn't currently used by any of the active code; I'm committing
this for completeness and in case any third party code attempts to
use it for legacy reasons.
It is reported that on some chips (e.g. the 970MP) behavior of POW bit set
simultaneously with modifying other bits is undefined and may cause hangs.
The race should be handled in some other way, but for now just get back.
Reported by: nwitehorn
CAM.
Desriptor sense is a new sense data format that originated in SPC-3. Among
other things, it allows for an 8-byte info field, which is necessary to
pass back block numbers larger than 4 bytes.
This change adds a number of new functions to scsi_all.c (and therefore
libcam) that abstract out most access to sense data.
This includes a bump of CAM_VERSION, because the CCB ABI has changed.
Userland programs that use the CAM pass(4) driver will need to be
recompiled.
camcontrol.c: Change uses of scsi_extract_sense() to use
scsi_extract_sense_len().
Use scsi_get_sks() instead of accessing sense key specific
data directly.
scsi_modes: Update the control mode page to the latest version (SPC-4).
scsi_cmds.c,
scsi_target.c: Change references to struct scsi_sense_data to struct
scsi_sense_data_fixed. This should be changed to allow the
user to specify fixed or descriptor sense, and then use
scsi_set_sense_data() to build the sense data.
ps3cdrom.c: Use scsi_set_sense_data() instead of setting sense data
manually.
cam_periph.c: Use scsi_extract_sense_len() instead of using
scsi_extract_sense() or accessing sense data directly.
cam_ccb.h: Bump the CAM_VERSION from 0x15 to 0x16. The change of
struct scsi_sense_data from 32 to 252 bytes changes the
size of struct ccb_scsiio, but not the size of union ccb.
So the version must be bumped to prevent structure
mis-matches.
scsi_all.h: Lots of updated SCSI sense data and other structures.
Add function prototypes for the new sense data functions.
Take out the inline implementation of scsi_extract_sense().
It is now too large to put in a header file.
Add macros to calculate whether fields are present and
filled in fixed and descriptor sense data
scsi_all.c: In scsi_op_desc(), allow the user to pass in NULL inquiry
data, and we'll assume a direct access device in that case.
Changed the SCSI RESERVED sense key name and description
to COMPLETED, as it is now defined in the spec.
Change the error recovery action for a number of read errors
to prevent lots of retries when the drive has said that the
block isn't accessible. This speeds up reconstruction of
the block by any RAID software running on top of the drive
(e.g. ZFS).
In scsi_sense_desc(), allow for invalid sense key numbers.
This allows calling this routine without checking the input
values first.
Change scsi_error_action() to use scsi_extract_sense_len(),
and handle things when invalid asc/ascq values are
encountered.
Add a new routine, scsi_desc_iterate(), that will call the
supplied function for every descriptor in descriptor format
sense data.
Add scsi_set_sense_data(), and scsi_set_sense_data_va(),
which build descriptor and fixed format sense data. They
currently default to fixed format sense data.
Add a number of scsi_get_*() functions, which get different
types of sense data fields from either fixed or descriptor
format sense data, if the data is present.
Add a number of scsi_*_sbuf() functions, which print
formatted versions of various sense data fields. These
functions work for either fixed or descriptor sense.
Add a number of scsi_sense_*_sbuf() functions, which have a
standard calling interface and print the indicated field.
These functions take descriptors only.
Add scsi_sense_desc_sbuf(), which will print a formatted
version of the given sense descriptor.
Pull out a majority of the scsi_sense_sbuf() function and
put it into scsi_sense_only_sbuf(). This allows callers
that don't use struct ccb_scsiio to easily utilize the
printing routines. Revamp that function to handle
descriptor sense and use the new sense fetching and
printing routines.
Move scsi_extract_sense() into scsi_all.c, and implement it
in terms of the new function, scsi_extract_sense_len().
The _len() version takes a length (which should be the
sense length - residual) and can indicate which fields are
present and valid in the sense data.
Add a couple of new scsi_get_*() routines to get the sense
key, asc, and ascq only.
mly.c: Rename struct scsi_sense_data to struct
scsi_sense_data_fixed.
sbp_targ.c: Use the new sense fetching routines to get sense data
instead of accessing it directly.
sbp.c: Change the firewire/SCSI sense data transformation code to
use struct scsi_sense_data_fixed instead of struct
scsi_sense_data. This should be changed later to use
scsi_set_sense_data().
ciss.c: Calculate the sense residual properly. Use
scsi_get_sense_key() to fetch the sense key.
mps_sas.c,
mpt_cam.c: Set the sense residual properly.
iir.c: Use scsi_set_sense_data() instead of building sense data by
hand.
iscsi_subr.c: Use scsi_extract_sense_len() instead of grabbing sense data
directly.
umass.c: Use scsi_set_sense_data() to build sense data.
Grab the sense key using scsi_get_sense_key().
Calculate the sense residual properly.
isp_freebsd.h: Use scsi_get_*() routines to grab asc, ascq, and sense key
values.
Calculate and set the sense residual.
MFC after: 3 days
Sponsored by: Spectra Logic Corporation
same prefix. Since a single route entry is installed for the prefix
(without RADIX_MPATH), incoming packets on the interfaces that are not
associated with the prefix route may trigger an error message about
unable to allocation LLE entry, and fails L2. This patch makes sure a
valid route is present in the system, and allow the aforementioned
condition to exist and treats as valid.
Reviewed by: bz
MFC after: 5 days
- Replace instances of manual assembly instruction "hlt" call
with halt() function calling.
- In cpu_idle_mwait() avoid races in check to sched_runnable() using
the same pattern used in cpu_idle_hlt() with the 'hlt' instruction.
- Add comments explaining the logic behind the pattern used in
cpu_idle_hlt() and other idle callbacks.
In collabouration with: jhb, mav
Reviewed by: adri, kib
MFC after: 3 weeks
- Implement bus_adjust_resource() methods as far as necessary and in non-PCI
bridge drivers as far as feasible without rototilling them.
- As NEW_PCIB does a layering violation by activating resources at layers
above pci(4) without previously bubbling up their allocation there, move
the assignment of bus tags and handles from the bus_alloc_resource() to
the bus_activate_resource() methods like at least the other NEW_PCIB
enabled architectures do. This is somewhat unfortunate as previously
sparc64 (ab)used resource activation to indicate whether SYS_RES_MEMORY
resources should be mapped into KVA, which is only necessary if their
going to be accessed via the pointer returned from rman_get_virtual() but
not for bus_space(9) as the later always uses physical access on sparc64.
Besides wasting KVA if we always map in SYS_RES_MEMORY resources, a driver
also may deliberately not map them in if the firmware already has done so,
possibly in a special way. So in order to still allow a driver to decide
whether a SYS_RES_MEMORY resource should be mapped into KVA we let it
indicate that by calling bus_space_map(9) with BUS_SPACE_MAP_LINEAR as
actually documented in the bus_space(9) page. This is implemented by
allocating a separate bus tag per SYS_RES_MEMORY resource and passing the
resource via the previously unused bus tag cookie so we later on can call
rman_set_virtual() in sparc64_bus_mem_map(). As a side effect this now
also allows to actually indicate that a SYS_RES_MEMORY resource should be
mapped in as cacheable and/or read-only via BUS_SPACE_MAP_CACHEABLE and
BUS_SPACE_MAP_READONLY respectively.
- Do some minor cleanup like taking advantage of rman_init_from_resource(),
factor out the common part of bus tag allocation into a newly added
sparc64_alloc_bus_tag(), hook up some missing newbus methods and replace
some homegrown versions with the generic counterparts etc.
- While at it, let apb_attach() (which can't use the generic NEW_PCIB code
as APB bridges just don't have the base and limit registers implemented)
regarding the config space registers cached in pcib_softc and the SYSCTL
reporting nodes set up.
* The AR_ISR_RAC interrupt processing method has a subtle bug in all
the MAC revisions (including pre-11n NICs) until AR9300v2.
If you're unlucky, the clear phase clears an update to one of the
secondary registers, which includes TX status.
This shows up as a "watchdog timeout" if you're doing very low levels
of TX traffic. If you're doing a lot of non-11n TX traffic, you'll
end up receiving a TX interrupt from some later traffic anyway.
But when TX'ing 11n aggregation session traffic (which -HEAD isn't yet
doing), you may find that you're only able to TX one frame (due to
BAW restrictions) and this may end up hitting this race condition.
The only solution is to not use RAC and instead use AR_ISR and the
AR_ISR_Sx registers. The bit in AR_ISR which represents the secondary
registers are not cleared; only the AR_ISR_Sx bits are. This way
any updates which occur between the read and subsequent write will
stay asserted and (correctly) trigger a subsequent interrupt.
I've tested this on the AR5416, AR9160, AR9280. I will soon test
the AR9285 and AR9287.
* The AR_ISR TX and RX bits (and all others!) are set regardless of
whether the contents of the AR_IMR register. So if RX mitigation is
enabled, RXOK is going to be set in AR_ISR and it would normally set
HAL_INT_RX.
Fix the code to not set HAL_INT_RX when RXOK is set and RX mitigation
is compiled in. That way the RX path isn't prematurely called.
I would see:
* An interrupt would come in (eg a beacon, or TX completion) where
RXOK was set but RXINTM/RXMINT wasn't;
* ath_rx_proc() be called - completing RX frames;
* RXINTM/RXMINT would then fire;
* ath_rx_proc() would then be called again but find no frames in the
queue.
This fixes the RX mitigation behaviour to not overly call ath_rx_proc().
* Start to flesh out more correct timer interrupt handling - it isn't
kite/merlin specific. It's actually based on whether autosleep support
is enabled or not.
This is sourced from my 11n TX branch and has been tested for a few weeks.
Finally, the interrupt handling change should likely be implemented
for AR5210, AR5211 and AR5212.
There are some timing concerns which I've yet to fully map out.
In any case, there's an existing software driven mitigation method
for TX interrupts and when TX'ing 11n frames, the whole frame itself
generates an interrupt rather then the subframes.
The ieee80211_swbmiss() callout is not called with the ic lock held, so it's
quite possible the scheduler will run the callout during a state change.
This patch:
* changes the swbmiss callout to be locked by the ic lock
* enforces the ic lock being held across the beacon vap functions
by grabbing it inside beacon_miss() and beacon_swmiss().
This ensures that the ic lock is held (and thus the VAP state
stays constant) during beacon miss and software miss processing.
Since the callout is removed whilst the ic lock is held, it also
ensures that the ic lock can't be called during a state change
or exhibit any race conditions seen above.
Both Edgar and Joel report that this patch fixes the crash and
doesn't introduce new issues.
Reported by: Edgar Martinez <emartinez@kbcnetworks.com>
Reported by: Joel Dahl <joel@vnode.se>
Reported by: emaste
POSIX/SUSvN. The sigwait(2) syscall does return EINTR, and libc.so.7
contains the wrapper sigwait(3) which hides EINTR from callers. The
EINTR return is used by libthr to handle required cancellation point
in the sigwait(3).
To help the binaries linked against pre-libc.so.7, i.e. RELENG_6 and
earlier, to have right ABI for sigwait(3), transform EINTR return from
sigwait(2) into ERESTART.
Discussed with: davidxu
MFC after: 1 week
also use the streaming buffer of pre version 5/revision 2.3 hardware as
long as we stay away from context flushes (which iommu(4) so far doesn't
take advantage of). OpenSolaris does the same.
atomic operations behave as if the were followed by a memory barrier so
there's no need to include ones in the acquire variants of atomic(9).
Removing these results a small performance improvement, specifically this
is sufficient to compensate the performance loss seen in the worldstone
benchmark seen when using SCHED_ULE instead of SCHED_4BSD.
This change is inspired by Linux even more radically doing the equivalent
thing some time ago.
Thanks go to Peter Jeremy for additional testing.
appending the new mbuf to the chain reference but possibly causing an mbuf
nextpkt loop leading to a memory used after handoff (or having been freed)
and leaking an mbuf here.
Reviewed by: rwatson, brooks
MFC after: 3 days
Although I tried to fix this earlier by introducing HALDEBUG_G(), it
turns out there seem to be other cases where the pointer value is still
NULL.
* Fix DO_HALDEBUG() and the HALDEBUG macro to check whether ah is NULL
before deferencing it
* Remove HALDEBUG_G() as it's no longer needed
This is hopefully a merge candidate for 9.0-RELEASE as enabling
debugging at startup could result in a kernel panic.
into sleep after receiving interrupt, delaying interrupt thread execution
indefinitely until the next interrupt arrive.
Reviewed by: nwhitehorn
MFC after: 3 days
by present MegaCLI version. It has some special meaning for the first s/g
list entry, while the main s/g list begins from the the second entry, and
those lists should remain separate after loading to the busdma map.
- Fix bug in 32bit ioctl compatibility shims when s/g list consists of
more then on element.
Sponsored by: iXsystems, inc.
MFC after: 3 days
protected the dirty mask updates. The dirty mask updates are handled
by atomics after the r225840.
Submitted by: alc
Tested by: flo (sparc64)
MFC after: 2 weeks
word to handle the dirty mask updates in vm_page_clear_dirty_mask().
Remove the vm page queue lock around vm_page_dirty() call in vm_fault_hold()
the sole purpose of which was to protect dirty on architectures which
does not provide short or byte-wide atomics.
Reviewed by: alc, attilio
Tested by: flo (sparc64)
MFC after: 2 weeks
Import the rest of HID improvements from the branch:
- improve report descriptor parser in libusbhid to handle several kinds of
reports same time;
- add to the libusbhid API two functions wrapping respective kernel IOCTLs
for reading and writing reports;
- tune uhid IOCTL interface to allow reading and writing arbitrary report,
when multiple supported by the device;
- teach usbhidctl to set output and feature reports;
- make usbhidaction support all the same item names as bhidctl.
Sponsored by: iXsystems, inc.
rtsock allowing routing daemons to filter routing updates on an
rtsock per FIB.
Adjust raw_input() and split it into wrapper and a new function
taking an optional callback argument even though we only have one
consumer [1] to keep the hackish flags local to rtsock.c.
PR: kern/134931
Submitted by: multiple (see PR)
Suggested by: rwatson [1]
Reviewed by: rwatson
MFC after: 3 days
rather than the whole beacon interval.
The reference driver and Linux ath9k both choose 80% of the
beacon interval and they do it in the driver rather than
the HAL (Ath reference) or ath9k_hw (ath9k.)
This quietens stuck beacon conditions on my AR9220/AR9280
based NICs when a lot of burst broadcast/multicast traffic
is going on. It doesn't seem to annoy the earlier MACs as
much as the AR9280 and later one.
Obtained from: Linux ath9k, Atheros
local variable with a beacon interval of 100 TU. This never gets modified
if the beacon interval configuration changes.
This may have been correct in earlier times, but with the advent of
staggered beacons (which default to 1 / ATH_BCBUF beacon interval, so
25 TU here) this value is incorrect.
It is used to configure the default CABQ readytime. So here, the cabq
was being configured to be much greater than the target beacon timer
(TBTT.)
The driver should be configuring a cabq readytime value rather then
leaving it to the HAL to choose sensible defaults. This should be
done in the future - I'm simply trying to ensure sensible defaults
are chosen.
whle tracking down the system hang reported in kern/160662 and
corrected in revision 225806. The LOR is not the cause of the system
hang and indeed cannot cause an actual deadlock. However, it can
be easily eliminated by defering the acquisition of a buflock until
after all the vnode locks have been acquired.
Reported by: Hans Ottevanger
PR: kern/160662
wdog_kern_pat() acquires eventhandler mutex, thus it cannot work in
kernel context (from where kdb_trap() runs).
The right way to fix this is both offering the
cpu-stop-on-panic-and-skip-locking logic and also a context for KDB
to officially run. We can re-enable this (or a similar) improvement
when these 2 patches hit the tree.
Sponsored by: Sandvine Incorporated
Discussed with: emaste, rstone
MFC after: immediately
build the ip_fw_pfil.c hooks and ipfw even in case of no-ip under the
assumption that the private L2 hook (which hopefully eventually will be a
pfil hook as well) can still be useful.
Allow building the module without inet as well.
Glanced at by: jhb
MFC after: 3 days
syscall exit path. Otherwise, if SIGTRAP is ignored, that tdsendsignal()
do not want to deliver the signal, and debugger never get a notification
of exec.
Found and tested by: Anton Yuzhaninov <citrin citrin ru>
Discussed with: jhb
MFC after: 2 weeks
back-end features.
sys/dev/xen/netfront/netfront.c:
o Add xn_query_features() which reads the XenStore and
records the TSO, LRO, and chained ring-request support
of the backend.
o Rename xn_configure_lro() to xn_configure_features() and
use this routine to manage the setup of TSO, LRO, and
checksum offload.
o In create_netdev(), initialize if_capabilities and
if_hwassist to the capabilities found on all backends.
Delegate configuration of if_capenable and the TSO flag
if if_hwassist to xn_configure_features().
Reported by: Hugo Silva (fix inspired by patch provided)
Approved by: re
MFC after: 1 week
PV devices with the ioemu attribute set.
sys/dev/xen/netfront/netfront.c:
o If a mac address for the interface cannot be found
in the front-side XenStore tree, look for an entry
in the back-side tree. With ioemu devices, the
emulator does not populate the front side tree and
neither does Xend.
o Return an error rather than panic when an attach
attempt fails.
Reported by: Janne Snabb (fix inspired by patch provided)
PR: kern/154302
Approved by: re
Sponsored by: BQ Internet
sys/dev/xen/netfront/netfront.c:
o Implement netfront_suspend(), a specialized suspend
handler for the netfront driver. This routine simply
disables the carrier so the driver is idle during
system suspend processing.
o Fix a leak when re-initializing LRO during a link reset.
o In netif_release_tx_bufs(), when cleaning up the grant
references for our TX ring, use gnttab_end_foreign_access_ref
instead of attempting to grant the page again.
o In netif_release_tx_bufs(), we do not track mbufs associated
with mbuf chains, but instead just free each mbuf directly.
Use m_free(), not m_freem(), to avoid double frees of mbufs.
o Refactor some code to enhance clarity.
Approved by: re
MFC after: 1 week
Sponsored by: BQ Internet
sys/dev/xen/blkfront/block.h:
sys/dev/xen/blkfront/blkfront.c:
Remove now unused blkif_vdev_t from the blkfront soft.
sys/dev/xen/blkfront/blkfront.c:
o In blkfront_suspend(), indicate the desire to suspend
by changing the softc connected state to SUSPENDED, and
then wait for any I/O pending on the remote peer to
drain. Cancel suspend processing if I/O does not
drain within 30 seconds.
o Enable and update blkfront_resume(). Since I/O is
drained prior to the suspension of the VM, the complicated
recovery process performed by other Xen blkfront
implementations is avoided. We simply tear down the
connection to our old peer, and then re-connect.
o In blkif_initialize(), fix a resource leak and botched
return if we cannot allocate shadow memory for our
requests.
o In blkfront_backend_changed(), correct our response to
the XenbusStateInitialised state. This state indicates
that our backend peer has published sufficient data for
blkfront to publish ring information and other XenStore
data, not that a connection can occur. Blkfront now
will only perform connection processing in response to
the XenbusStateConnected state. This corrects an issue
where blkfront connected before the backend was ready
during resume processing.
Approved by: re
MFC after: 1 week
framework.
Sponsored by: BQ Internet
sys/xen/xenbus/xenbusb.c:
o In xenbusb_resume(), publish the state transition of the
resuming device into XenbusStateIntiailising so that the
remote peer can see it. Recording the state locally is
not sufficient to trigger a re-connect sequence.
o In xenbusb_resume(), defer new-bus resume processing until
after the remote peer's XenStore address has been updated.
The drivers may need to refer to this information during
resume processing.
sys/xen/xenbus/xenbusb_back.c:
sys/xen/xenbus/xenbusb_front.c:
Register xenbusb_resume() rather than bus_generic_resume()
as the handler for device_resume events.
sys/xen/xenstore/xenstore.c:
o Fix grammer in a comment.
o In xs_suspend(), pass suspend events on to the child
devices (e.g. xenbusb_front/back, that are attached
to the XenStore.
Approved by: re
MFC after: 1 week
This change fixes a race in device side mode during clear-stall from
host, which can cause data to be sent too early on the given
endpoint.
Approved by: re (kib)
MFC after: 1 week
thing all the other architectures already do) thus just initialize
kernel_pmap in pmap_bootstrap().
Reported by: alc
Reviewed by: alc, marius
Tested by: flo, marius
Approved by: re (kib)
MFC after: 1 week
we were accounting the newly created process to its parent instead
of the child itself. This caused problems later, when the child
changed its credentials - the per-uid, per-jail etc counters were
not properly updated, because the maxproc counter in the child
process was 0.
Approved by: re (kib)
initialization. Prior to this change packets may be transmitted with an
incorrect checksum.
Em(4) already has an equivalent change in r213234.
Obtained From: Sandvine
MFC After: 1 week
Approved by: re (bz)
patch modifies makesyscalls.sh to prefix all of the non-compatibility
calls (e.g. not linux_, freebsd32_) with sys_ and updates the kernel
entry points and all places in the code that use them. It also
fixes an additional name space collision between the kernel function
psignal and the libc function of the same name by renaming the kernel
psignal kern_psignal(). By introducing this change now we will ease future
MFCs that change syscalls.
Reviewed by: rwatson
Approved by: re (bz)
build it with and without INET/INET6 support.
Submitted by: Alexander V. Chernikov <melifaro at yandex-team.ru> [1]
Tested by: Alexander V. Chernikov <melifaro at yandex-team.ru> [1]
Approved by: re (bz)
MFC after: 2 weeks
the code to have the fall-through path to follow the likely target.
Do not use intermediate register to reload user %rsp.
Proposed by: alc
Reviewed by: alc, jhb
Approved by: re (bz)
MFC after: 2 weeks
If it overflows before the taskqueue can run, the task will be
re-added to the taskqueue and cause a loop in the task list.
Reported by: Arnaud Lacombe <lacombar@gmail.com>
Submitted by: Ryan Stone <rysto32@gmail.com>
Reviewed by: jhb
Approved by: re (kib)
MFC after: 1 day
We are allocating some kilobytes of extra memory during USB device enumeration.
This does not change alot under FreeBSD, but makes sense for various embedded
operating systems using the FreeBSD USB stack, which have less memory
resources available.
Approved by: re (kib)
MFC after: 1 week
on vfc_name to set vfc_typenum, so that vfc_typenum doesn't
change when file systems are loaded in different orders. This
keeps NFS file handles from changing, for file systems that
use vfc_typenum in their fsid. This change is controlled via
a loader.conf variable called vfs.typenumhash, since vfc_typenum
will change once when this is enabled. It defaults to 1 for
9.0, but will default to 0 when MFC'd to stable/8.
Tested by: hrs
Reviewed by: jhb, pjd (earlier version)
Approved by: re (kib)
MFC after: 1 month
gpt and zfs boot blocks are not nearly as size-constrained as boot2
from which they inherited their current optimization and anti-optimization
options. As such the current options do not provide any benefit, but
make debugging of the code much harder.
Also, it has been demonstrated that combination of -mrtd and
-fno-unit-at-a-time may result in mis-compilation of the boot code
with the current base gcc.
Additionally, intermediate assembly file filtering is removed for
zfsboot.
The new boot blocks are all compile- and boot- tested using qemu.
gptzfsboot is tested with real hardware.
Reported by: Peter Jeremy <peterjeremy@acm.org> [miscompilation]
Discussed with: bde, jhb
Tested by: Sebastian Chmielewski <chmielsster@gmail.com> [gptzfsboot]
Approved by: re (kib)
MFC after: 3 weeks
The utility is not connected to the build, so it should be safe
to update it.
To do: move the utility to tools/.
Some code is provided by Peter Jeremy <peterjeremy@acm.org>
Tested by: Sebastian Chmielewski <chmielsster@gmail.com>,
Peter Jeremy <peterjeremy@acm.org> (earlier versions)
Approved by: re (kib)
MFC after: 4 days
(r225485). When setting an interface name to it, the following
configurations will be enabled:
1. "no_radr" is set to all IPv6 interfaces automatically.
2. "-no_radr accept_rtadv" will be set only for $ipv6_cpe_wanif. This is
done just before evaluating $ifconfig_IF_ipv6 in the rc.d scripts (this
means you can manually supersede this configuration if necessary).
3. The node will add RA-sending routers to the default router list
even if net.inet6.ip6.forwarding=1.
This mode is added to conform to RFC 6204 (a router which connects
the end-user network to a service provider network). To enable
packet forwarding, you still need to set ipv6_gateway_enable=YES.
Note that accepting router entries into the default router list when
packet forwarding capability and a routing daemon are enabled can
result in messing up the routing table. To minimize such unexpected
behaviors, "no_radr" is set on all interfaces but $ipv6_cpe_wanif.
Approved by: re (bz)
options defined in the kernel config. This more closely matches the
behavior of other modules which inherit configuration settings from the
kernel configuration during a kernel + modules build.
Reviewed by: luigi
Approved by: re (kib)
MFC after: 1 week
of the device boundry.
While this is generally ok, the problem is that all the consumers
handle similar cases (and expect to catch) ENOSPC for this (for a
reference look at minidumpsys() and dumpsys() constructions). That
ends up in consumers not recognizing the issue and amd64 failing to
retry if the number of pages grows up during minidump.
Fix this by returning ENOSPC in dump_write() and while here add some
more diagnostic on involved values.
Sponsored by: Sandvine Incorporated
In collabouration with: emaste
Approved by: re (kib)
MFC after: 10 days
the BAR after parsing the CIS. This forces the resource range to be
reallocated if the BAR is reused by the device.
Submitted by: deischen
Reviewed by: imp
Approved by: re (kib)
In revision 223722 we introduced support for driver ioctls on init/lock
state devices. Unfortunately the call to ttydevsw_cioctl() clobbers the
value of the error variable, meaning that in many cases ioctl() will now
return ENOTTY, even though the ioctl() was processed properly.
Reported by: Boris Samorodov <bsam ipt ru>
Patch by: jilles@
Approved by: re@ (kib@)
sequence. The effect is ~1% on the microbenchmark.
In particular, do not restore registers which are preserved by the
C calling sequence. Align the jump target. Avoid unneeded memory
accesses by calculating some data in syscall entry trampoline.
Reviewed by: jhb
Approved by: re (bz)
MFC after: 2 weeks
- Axe out the SHOW_BUSYBUFS option and uses a tunable for selectively
enable/disable it, which is defaulted for not printing anything (0
value) but can be changed for printing (1 value) and be verbose (2
value)
- Improves the informations outputed: right now, there is no track of
the actual struct buf object or vnode which are referenced by the
shutdown process, but it is printed the related struct bufobj object
which is not really helpful
- Add more verbosity about the state of the struct buf lock and the
vnode informations, with the latter to be activated separately by the
sysctl
Sponsored by: Sandvine Incorporated
Reviewed by: emaste, kib
Approved by: re (ksmith)
MFC after: 10 days
This is another commit in a series of TDMA support fixes for the 11n NICs.
* Move ath_hal_getnexttbtt() into the HAL; write methods for it.
This returns a timer value in TSF, rather than TU.
* Move ath_hal_getcca() and ath_hal_setcca() into the HAL too, where they
likely now belong.
* Create a new HAL capability: HAL_CAP_LONG_RXDESC_TSF.
The pre-11n NICs write 15 bit TSF snapshots into the RX descriptor;
the AR5416 and later write 32 bit TSF snapshots into the RX descriptor.
* Use the new capability to choose between 15 and 31 bit TSF adjustment
functions in ath_extend_tsf().
* Write ar5416GetTsf64() and ar5416SetTsf64() methods.
ar5416GetTsf64() tries to compensate for TSF changes at the 32 bit boundary.
According to yin, this fixes the TDMA beaconing on 11n chipsets and TDMA
stations can now associate/talk, but there are still issues with traffic
stability which need to be investigated.
The ath_hal_extendtsf() function is also used in RX packet timestamping;
this may improve adhoc mode on the 11n chipsets. It also will affect the
timestamps seen in radiotap frames.
Submitted by: Kang Yin Su <cantona@cantona.net>
Approved by: re (kib)
whenever the link state is changed. Using software based polling
for media status tracking is known to cause MII access failure
under certain conditions once link is established so vge(4) used to
rely on link status change interrupt.
However DEVICE_POLLING completely disables generation of all kind
of interrupts on vge(4) such that this resulted in not detecting
link state change event. This means vge(4) does not correctly
detect established/lost link with DEVICE_POLLING. Losing the
interrupt made vge(4) not to send any packets to peer since vge(4)
does not try to send any packets when there is no established link.
Work around the issue by generating link state change interrupt
with DEVICE_POLLING.
PR: kern/160442
Approved by: re (kib)
reference driver does clear the async interrupts after each service.
I'll tinker with this in a future commit.
Obtained from: Atheros
Approved by: re (kib)
such as j:name:maxproc:sigkill=100. Proper fix - deferring psignal
to a taskqueue - is somewhat complicated and thus will happen
after 9.0.
Approved by: re (kib)
When the fast clock (44mhz) is enabled for 5ghz HT20, the
dual ADCs aren't enabled. Trying to do the ADC calibrations
here would result in calibration never completing; this
resulted in IQ calibration never running and thus performance
issues in 11a/11n HT20 mode.
Leave it enabled for non-fastclock (40mhz) 11a mode and
HT40 modes.
This has been fixed in discussion with Felix Fietkau (nbd)
and discussions with the Atheros baseband team.
Linux ath9k now has a similar fix.
Approved by: re (kib)
flags field. Updates to the atomic flags are performed using the atomic
ops on the containing word, do not require any vm lock to be held, and
are non-blocking. The vm_page_aflag_set(9) and vm_page_aflag_clear(9)
functions are provided to modify afalgs.
Document the changes to flags field to only require the page lock.
Introduce vm_page_reference(9) function to provide a stable KPI and
KBI for filesystems like tmpfs and zfs which need to mark a page as
referenced.
Reviewed by: alc, attilio
Tested by: marius, flo (sparc64); andreast (powerpc, powerpc64)
Approved by: re (bz)
The current code was rounding down the maximum frame size instead of
routing up, resulting in a read size of 1024 bytes, in the non-jumbo
frame case, and splitting the packets across multiple mbufs.
Consequently the above problem exposed another issue, which is when
packets were splitted across multiple mbufs, and all of the mbufs in the
chain have the M_PKTHDR flag set.
Submitted by: original patch by Ray Ruvinskiy at BlueCoat dot com
Reviewed by: jfv, kmacy, rwatson
Approved by: re (rwatson)
MFC after: 5 days
is retrieved after a failed SCSI command to continue normal
operation. Else this sense information is retrived at the next
SCSI command.
Approved by: re (kib)
Reported by: Alex Kozlov
MFC after: 1 week
PR: usb/160299
* Update the hardware access register definitions and functions to bring
them in line with other Netlogic software.
* Update the platform bus to use PCI even for on-chip devices. Add a dummy
PCI driver to ignore on-chip devices which do not need driver.
* Provide memory and IRQ resource allocation code for on-chip devices
which cannot get it from PCI config.
* add support for on-chip PCI and USB interfaces.
* update conf files, enable pci and retain old MAXCPU until we can support
>32 cpus.
Approved by: re(kib), jmallett
hostid, this gives a good chance of keeping the same address over
reboots. This is intended to help IPV6 and similar which generate
their addresses from the mac.
PR: kern/160300
Submitted by: mdodd
Approved by: re (kib)
While this is generally good, it brings along a serie of problems,
like clocks going off sync and in presence of SW_WATCHDOG, watchdogs
firing without a good reason (missed hardclock wdog ticks update).
Fix the latter by kicking the watchdog just before to re-enable the interrupts.
Also, while here, not rely on users to stop the watchdog manually when
entering DDB but do that when entering KDB context.
Sponsored by: Sandvine Incorporated
Reviewed by: emaste, rstone
Approved by: re (kib)
MFC after: 1 week
which requires that ni_strictrelative be set to 0, post-r224810.
Tested by: swills (earlier version), geo dot liaskos at gmail.com
Approved by: re (kib)
pre-r222417 state. The behavior was essentially reversed in r222417
which can cause confusion.
PR: 159775
Submitted by: Devin Teske
Approved by: re (kib)
which does not support the no synchronize cache SCSI command.
The __FreeBSD_version version macro has been bumped and
external kernel modules needs to be recompiled after
this patch.
Approved by: re (kib)
MFC after: 1 week
PR: usb/160299
and the new setmode and setowner fileops in FreeBSD 9.0:
- Add new MAC Framework entry point mac_posixshm_check_create() to allow
MAC policies to authorise shared memory use. Provide a stub policy and
test policy templates.
- Add missing Biba and MLS implementations of mac_posixshm_check_setmode()
and mac_posixshm_check_setowner().
- Add 'accmode' argument to mac_posixshm_check_open() -- unlike the
mac_posixsem_check_open() entry point it was modeled on, the access mode
is required as shared memory access can be read-only as well as writable;
this isn't true of POSIX semaphores.
- Implement full range of POSIX shared memory entry points for Biba and MLS.
Sponsored by: Google Inc.
Obtained from: TrustedBSD Project
Approved by: re (kib)
- tjmax - Tj(max) value from the CPU
- delta - current delta reading
- resolution - sensor resolution in Celsius
- throttle_log - whether a #PROCHOT was asserted since last reset
Submitted by: Mark Johnston <markjdb gmail.com> (mostly)
MFC after: 1 month
Approved by: re (kib)
been interrupted in a restartable syscall. Otherwise we could end up
in an (almost) endless loop in clnt_reconnect_call().
PR: kern/160198
Reviewed by: rmacklem
Approved by: re (kib), avg (mentor)
MFC after: 1 week
which may cause problems when these contain garbage so zero the range
descriptors embedding the rmans when allocating them.
Approved by: re (kib)
MFC after: 3 days
