Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
- Use the existing vbus locks instead of Giant for the CAM sim lock.
- Use callout(9) instead of timeout(9).
- Mark the interrupt handler MPSAFE.
- Don't attempt to pass data in the softc from probe() to attach().
- Remove compat shims for FreeBSD versions older than 8.0.
Reviewed by: Steve Chang <ychang@highpoint-tech.com>
original, this hides the contents of cam_compat.h from ktrace/kdump/truss,
avoiding problems there. There are no user-servicable parts in there, so
no need for those tools to be groping around in there.
Approved by: re
- Remove the timeout_ch field. It's been deprecated since FreeBSD 7.0;
MPSAFE drivers should be managing their own timeout storage. The
remaining non-MPSAFE drivers have been modified to also manage their own
storage, and should be considered for updating to MPSAFE (or removal)
during the FreeBSD 10.x lifecycle.
- Add fields related to soft timeouts and quality of service, to be used
in upcoming work.
- Add room for more flags in the CCB header and path_inq structures.
- Begin support for extended 64-bit LUNs.
- Bump the CAM version number to 0x18, but add compat shims. Tested with
camcontrol and smartctl.
Reviewed by: nathanw, ken, kib
Approved by: re
Obtained from: Netflix
- Unify bus reset/probe sequence. Whenever bus attached at boot or later,
CAM will automatically reset and scan it. It allows to remove duplicate
code from many drivers.
- Any bus, attached before CAM completed it's boot-time initialization,
will equally join to the process, delaying boot if needed.
- New kern.cam.boot_delay loader tunable should help controllers that
are still unable to register their buses in time (such as slow USB/
PCCard/ CardBus devices), by adding one more event to wait on boot.
- To allow synchronization between different CAM levels, concept of
requests priorities was extended. Priorities now split between several
"run levels". Device can be freezed at specified level, allowing higher
priority requests to pass. For example, no payload requests allowed,
until PMP driver enable port. ATA XPT negotiate transfer parameters,
periph driver configure caching and so on.
- Frozen requests are no more counted by request allocation scheduler.
It fixes deadlocks, when frozen low priority payload requests occupying
slots, required by higher levels to manage theit execution.
- Two last changes were holding proper ATA reinitialization and error
recovery implementation. Now it is done: SATA controllers and Port
Multipliers now implement automatic hot-plug and should correctly
recover from timeouts and bus resets.
- Improve SCSI error recovery for devices on buses without automatic sense
reporting, such as ATAPI or USB. For example, it allows CAM to wait, while
CD drive loads disk, instead of immediately return error status.
- Decapitalize diagnostic messages and make them more readable and sensible.
- Teach PMP driver to limit maximum speed on fan-out ports.
- Make boot wait for PMP scan completes, and make rescan more reliable.
- Fix pass driver, to return CCB to user level in case of error.
- Increase number of retries in cd driver, as device may return several UAs.
cards:
o RocketRAID 172x series
o RocketRAID 174x series
o RocketRAID 2210
o RocketRAID 222x series
o RocketRAID 2240
o RocketRAID 230x series
o RocketRAID 231x series
o RocketRAID 232x series
o RocketRAID 2340
o RocketRAID 2522
Many thanks to Highpoint for their continued support of FreeBSD.
Submitted by: Highpoint
