Clocks, GPIO, UART, SD card / eMMC, USB, watchdog, and ethernet are
supported. Note that the A83T contains two clusters of four Cortex-A7
CPUs, and only CPUs in first cluster are started for now.
Tested on a Sinovoip Banana Pi BPI-M3.
Different versions of firmware have different requirments for TX/RX
packet layouts (and other things, of course.) Currently the driver
checks between 3xx and 4xx firmware by using the BWN_ISOLDFMT() macro,
which doesn't take into account the 5xx firmware (which I think I need
for the HT and N series PHY chips. I'll know when I do the port.)
BWN_HDRSIZE() also needs to learn about the 5xx series firmware
as well.
So:
* add a firmware version enum
* populate it based on the firmware version we read at load time
* don't finish loading if the firmware is the 5xx firmware; any
code using BWN_ISOLDFMT or BWN_HDRSIZE needs updating (most notably
the TX and RX bits.)
Then, for RX RSSI:
* write down and reimplement the b43 rssi calculation method;
* use it for the correct PHYs (which are all the ones we support);
* do the RSSI calculation before radiotap, not after.
Tested:
* Broadcom BCM4312, STA mode
Obtained from: Linux b43 (careful writing and reimplementing; lots of integer math..)
The change broke buildworld when building lib/libkvm
This change likely needs to be run through a ports -exp run as a sanity
check, as it might break downstream consumers.
Pointyhat to: adrian
Reported by: kargl (confirmed on $work workstation)
Sponsored by: EMC / Isilon Storage Division
Don't crash if the user has more than 31 of them. A follow-up to
r298230.
Reviewed by: allanjude
Relnotes: maybe
Sponsored by: EMC / Isilon Storage Division
Differential Revision: https://reviews.freebsd.org/D6212
This is an initial work in progress to use the replacement bhnd
bus code for devices which support it.
* Add manpage updates for bhnd, bhndb, siba
* Add kernel options for bhnd, bhndbus, etc
* Add initial support in if_bwn_pci / if_bwn_mac for using bhnd
as the bus transport for suppoted NICs
* if_bwn_pci will eventually be the PCI bus glue to interface to bwn,
which will use the right backend bus to attach to, versus direct
nexus/bhnd attachments (as found in embedded broadcom devices.)
The PCI glue defaults to probing at a lower level than the bwn glue,
so bwn should still attach as per normal without a boot time tunable set.
It's also not fully fleshed out - the bwn probe/attach code needs to be
broken out into platform and bus specific things (just like ath, ath_pci,
ath_ahb) before we can shift the driver over to using this.
Tested:
* BCM4311, STA mode
* BCM4312, STA mode
Submitted by: Landon Fuller <landonf@landonf.org>
Differential Revision: https://reviews.freebsd.org/D6191
after r298107
Summary of changes:
- Replace all instances of FILES/TESTS with ${PACKAGE}FILES. This ensures that
namespacing is kept with FILES appropriately, and that this shouldn't need
to be repeated if the namespace changes -- only the definition of PACKAGE
needs to be changed
- Allow PACKAGE to be overridden by callers instead of forcing it to always be
`tests`. In the event we get to the point where things can be split up
enough in the base system, it would make more sense to group the tests
with the blocks they're a part of, e.g. byacc with byacc-tests, etc
- Remove PACKAGE definitions where possible, i.e. where FILES wasn't used
previously.
- Remove unnecessary TESTSPACKAGE definitions; this has been elided into
bsd.tests.mk
- Remove unnecessary BINDIRs used previously with ${PACKAGE}FILES;
${PACKAGE}FILESDIR is now automatically defined in bsd.test.mk.
- Fix installation of files under data/ subdirectories in lib/libc/tests/hash
and lib/libc/tests/net/getaddrinfo
- Remove unnecessary .include <bsd.own.mk>s (some opportunistic cleanup)
Document the proposed changes in share/examples/tests/tests/... via examples
so it's clear that ${PACKAGES}FILES is the suggested way forward in terms of
replacing FILES. share/mk/bsd.README didn't seem like the appropriate method
of communicating that info.
MFC after: never probably
X-MFC with: r298107
PR: 209114
Relnotes: yes
Tested with: buildworld, installworld, checkworld; buildworld, packageworld
Sponsored by: EMC / Isilon Storage Division
The previous change to split the worker thread start out of fdc_attach()
did not start the worker thread if the fdc device in the ACPI namespace
did not have an _FDE method. This fixes hangs when booting with a
floppy controller enabled on certain machines with ACPI.
Tested by: joel
Two new functions are provided, bit_ffs_at() and bit_ffc_at(), which allow
for efficient searching of set or cleared bits starting from any bit offset
within the bit string.
Performance is improved by operating on longs instead of bytes and using
ffsl() for searches within a long. ffsl() is a compiler builtin in both
clang and gcc for most architectures, converting what was a brute force
while loop search into a couple of instructions.
All of the bitstring(3) API continues to be contained in the header file.
Some of the functions are large enough that perhaps they should be uninlined
and moved to a library, but that is beyond the scope of this commit.
sys/sys/bitstring.h:
Convert the majority of the existing bit string implementation from
macros to inline functions.
Properly protect the implementation from inadvertant macro expansion
when included in a user's program by prefixing all private
macros/functions and local variables with '_'.
Add bit_ffs_at() and bit_ffc_at(). Implement bit_ffs() and
bit_ffc() in terms of their "at" counterparts.
Provide a kernel implementation of bit_alloc(), making the full API
usable in the kernel.
Improve code documenation.
share/man/man3/bitstring.3:
Add pre-exisiting API bit_ffc() to the synopsis.
Document new APIs.
Document the initialization state of the bit strings
allocated/declared by bit_alloc() and bit_decl().
Correct documentation for bitstr_size(). The original code comments
indicate the size is in bytes, not "elements of bitstr_t". The new
implementation follows this lead. Only hastd assumed "elements"
rather than bytes and it has been corrected.
etc/mtree/BSD.tests.dist:
tests/sys/Makefile:
tests/sys/sys/Makefile:
tests/sys/sys/bitstring.c:
Add tests for all existing and new functionality.
include/bitstring.h
Include all headers needed by sys/bitstring.h
lib/libbluetooth/bluetooth.h:
usr.sbin/bluetooth/hccontrol/le.c:
Include bitstring.h instead of sys/bitstring.h.
sbin/hastd/activemap.c:
Correct usage of bitstr_size().
sys/dev/xen/blkback/blkback.c
Use new bit_alloc.
sys/kern/subr_unit.c:
Remove hard-coded assumption that sizeof(bitstr_t) is 1. Get rid of
unrb.busy, which caches the number of bits set in unrb.map. When
INVARIANTS are disabled, nothing needs to know that information.
callapse_unr can be adapted to use bit_ffs and bit_ffc instead.
Eliminating unrb.busy saves memory, simplifies the code, and
provides a slight speedup when INVARIANTS are disabled.
sys/net/flowtable.c:
Use the new kernel implementation of bit-alloc, instead of hacking
the old libc-dependent macro.
sys/sys/param.h
Update __FreeBSD_version to indicate availability of new API
Submitted by: gibbs, asomers
Reviewed by: gibbs, ngie
MFC after: 4 weeks
Sponsored by: Spectra Logic Corp
Differential Revision: https://reviews.freebsd.org/D6004
The datasheets refer to this controller as EMAC, not to be confused with
the fast ethernet controller (also named EMAC) found in A10/A20 SoCs.
Tested on a BananaPi M3 (A83T), which uses an external RGMII PHY (RTL8211E).
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D6169
call pmap_invalidate_page() even though they are not destroying a leaf-
level page table entry.
Eliminate some bogus white-space characters in a comment.
Reviewed by: kib
Add the needed hardcoded gem5 attachments for the UART there, re-using all
the other bits.
In collaboration with: andrew
Sponsored by: DARPA/AFRL
Reviewed by: andrew
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D6204
In case we do not have an interrupt assignment for the virtual timer,
force the physical timer.
Also skip resource allocation for any timer we do not have an interrupt
assignment for.
In collaboration with: andrew
Submitted by: br ([1] from his gem5 arm64 work)
Sponsored by: DARPA/AFRL
Reviewed by: andrew
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D6203
In case of updating it with a very low value it might expire again
after writing the tval but before updating ctrl. In that case we do
lose the status bit saying that the timer expired and we will consequently
not get an interrupt for it, leaving the timer in a "dead" state.
In order to solve this increase the minimum period with what the timer
can be loaded to something higher.
Found & analysed with: gem5
Debugged with: andrew
Sponsored by: DARPA/AFRL
Reviewed by: andrew
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D6202
The Xen PV clock has a resolution of 1ns, so set the resolution to the
highest one that FreeBSD supports, which is 1us.
MFC after: 2 weeks
Sponsored by: Citrix Systems R&D
The current code in clock_register checks if the newly added clock has a
resolution value higher than the current one in order to make it the
default, which is wrong. Clocks with a lower resolution value should be
better than ones with a higher resolution value, in fact with the current
code FreeBSD is always selecting the worse clock.
Reviewed by: kib jhb jkim
Sponsored by: Citrix Systems R&D
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D6185
* Add a debug print for the xmit completion status fields.
Yes, I like staring at a stream of DWORDS.
* Set the retrycnt to the number of full frame retries for now;
I'll figure out how to factor rts/cts failures into it when
I figure out what the difference is.
It's -1 because it's not "retries", it's "tries".
It now passes the youtube test.
Tested:
* BCM4312, STA mode
I noticed that it'd associate fine, but it'd quickly stop exchanging traffic.
Receive was okay, but transmit just failed.
Then I went "wlandebug +rate". I discovered it started at 36M OFDM, and then
quickly rose to 54M, which then showed 0% transmit success.
Then, I dug into how the completion path works. We are reading 'ack=0'
in the TX status side, so .. then I discovered we were only processing the
TX completion status /if/ ack=1. So, we'd only ever count successes;
we'd never count failures, and thus the rate control code thought
everything was a-ok.
We also have to set retrycnt to something non-zero so it indeed does
bring the rate down upon failure.
So:
* Delete the rate control completion code from the tx completion
routine, it's just duplicate and never worked. Putting it behind
'if (status->ack) was pointless.
* Move it to the PIO and DMA completion routines which actually
do free the node reference and mbuf. We know at that point
what the status is, so do it there.
* Fake a retrycnt of 1 for now, so we at least count failures.
Also:
* Start adding comments about weird stuff I find with rate selection.
In this instance, we shouldn't be selecting a fallback rate that
doesn't match the currently configured mode (11a, 11b, 11g, etc.)
This isn't perfect - AMRR does try 54mbit and takes a few packets
before it figures out it's a bad idea - but it's better than nothing.
This makes the bwn(4) driver actually useful for the first time since
I've tried using it - and that dates back to 2011. I've resisted
successfully until now.
Tested:
* Broadcom BCM4312 802.11b/g Wireless, STA mode
WLAN (chipid 0x4312 rev 15) PHY (analog 6 type 5 rev 1) RADIO (manuf 0x17f ver 0x2062 rev 2)
TODO:
* See if the fallback rate actually /is/ working
* Question my own sanity over touching this driver in the first place.
Falling back from 6MB OFDM to 5MB CCK (a) may not work well in the
11bg PHYs, (b) won't work at all if you're 11g only, and (c) plainly
won't work for the 11a PHY.
So, don't do that!
Tested:
* BCM4312 802.11b/g Wireless, STA mode
WLAN (chipid 0x4312 rev 15) PHY (analog 6 type 5 rev 1) RADIO (manuf 0x17f ver 0x2062 rev 2)
Instead of panicking when parsing an invalid ACPI SRAT table,
just ignore it, effectively disabling NUMA.
https://lists.freebsd.org/pipermail/freebsd-current/2016-May/060984.html
Reported and tested by: Bill O'Hanlon (bill.ohanlon at gmail.com)
Reviewed by: jhb
MFC after: 1 week
Relnotes: If dmesg shows "SRAT: Duplicate local APIC ID",
try updating your BIOS to fix NUMA support.
Sponsored by: Dell Inc.
Save the value of the IOV control and page size registers and restore
them (along with the VF count) in pci_cfg_save/pci_cfg_restore. This
ensures ARI remains enabled if a PF driver resets itself during the
PCI_IOV_INIT callback. This might also properly restore SRIOV state
across suspend/resume.
Reviewed by: rstone, vangyzen
Differential Revision: https://reviews.freebsd.org/D6192
While here, check if ARI was enabled by re-reading the config register
after writing it and return an error if the write fails.
Reviewed by: rstone, vangyzen
