This simplifies checking for default resource range for bus_alloc_resource(),
and improves readability.
This is part of, and related to, the migration of rman_res_t from u_long to
uintmax_t.
Discussed with: jhb
Suggested by: marcel
Summary:
Migrate to using the semi-opaque type rman_res_t to specify rman resources. For
now, this is still compatible with u_long.
This is step one in migrating rman to use uintmax_t for resources instead of
u_long.
Going forward, this could feasibly be used to specify architecture-specific
definitions of resource ranges, rather than baking a specific integer type into
the API.
This change has been broken out to facilitate MFC'ing drivers back to 10 without
breaking ABI.
Reviewed By: jhb
Sponsored by: Alex Perez/Inertial Computing
Differential Revision: https://reviews.freebsd.org/D5075
- Detach the gpiobus and the gpioc devices from the GPIO controller.
- Fix the leak of gpiobus IRQ rman(9) region descriptor.
- Fix the leak of child ivars and IRQ resource list.
While here return NULL (instead of 0) for a device_t that fails to allocate
the ivar memory.
Tested with gpiobus built as a module.
Sponsored by: Rubicon Communications (Netgate)
Brightness is controlled through sysctl dev.gpiobacklight.X.brightness:
- any value greater than 0: backlight is on
- any value less than or equal to 0: backlight is off
FDT bindings docs in Linux tree:
Documentation/devicetree/bindings/video/backlight/gpio-backlight.txt
adding already exists and if so just return that. The typical use case
is from identify routines, which shouldn't be adding multiple copies
of the same phandle_t to the gpiobus. Only one per phandle_t is needed
(or expected by the current code).
Differential Revision: https://reviews.freebsd.org/D2871
https://www.kernel.org/doc/Documentation/devicetree/bindings/leds/leds-gpio.txt
Without this booting the VSATV102 causes the blue "working" led to turn
off when the kernel starts up. With this the led (which is turned on by
the firmware) stays on since that's the default state specified in the FDT.
Expanded the meaning of the led_create_state state parameter in order
to implement support for "keep". The original values were:
== 0 Off
!= 0 On
The new values are:
== -1 don't change / keep current setting
== 0 Off
!= -1 && != 0 On
This should have no effect on acpi_asus_attach which only calls
led_create_state with state set to 1. Updated acpi_ibm_attach
in order to avoid surprises.
Differential Revision: https://reviews.freebsd.org/D2615
Submitted by: John Wehle
Reviewed by: gonzo, loos
There are cases when gpioled nodes in DTS come from different sources
(e.g. standard Beaglebone Black LEDs in main DTS + shield LEDs in
overlay DTS) so instead of handling only first compatible node go
through all child nodes
When a gpiobus child is added, use its name to identify the mapped pin
names.
Make the respective changes to libgpio.
Add a new '-n' flag to gpioctl(8) to set the pin name.
Differential Revision: https://reviews.freebsd.org/D2002
Reviewed by: rpaulo
Requested by: many
rework the code a little bit to use this function consistently to cleanup
all the changes made as part of the probe phase.
This fixes an issue where a FDT child node without a matching driver could
leave the GPIO pins mapped and prevent the further use of them.
This prints a warning when your system have a hinted child or a FDT child
node for which you don't have a matching driver:
gpiobus0: <unknown device> at pin(s) 24 irq 24
This new function can be used by other drivers to reserve the use of GPIO
pins.
Anyway, the use of ofw_gpiobus_parse_gpios() is preferred when possible.
Requested by: Michal Meloun
property for devices that doesn't descend directly from gpiobus.
The parser supports multiple pins, different GPIO controllers and can use
arbitrary names for the property (to match the many linux variants:
cd-gpios, power-gpios, wp-gpios, etc.).
Pass the driver name on ofw_gpiobus_add_fdt_child(). Update gpioled to
match.
An usage example of ofw_gpiobus_parse_gpios() will follow soon.
controller.
The gpiobus is responsible to keep track of the used pins and serialize
the access to pins.
Some of these features are important to devices that do not descend
directly from gpiobus and as such cannot make use of its features (one
classic example is gpioc that is attached to the GPIO controller and could
not, until now, make use of the gpiobus locking).
This is the general support to allow the use of GPIO pins as interrupt
sources for direct gpiobus children.
The use of GPIO pins as generic interrupt sources (for an ethernet driver
for example) will only be possible when arm/intrng is complete. Then, most
of this code will need to be rewritten, but it works for now, is better
than what we have and will allow further developments.
Tested on: ar71xx (RSPRO), am335x (BBB), bcm2835 (Raspberry pi)
Differential Revision: https://reviews.freebsd.org/D999
Reviewed by: rpaulo
hold the gpiobus lock between the gpio calls.
gpiobus_acquire_lock() now accepts a third parameter which tells gpiobus
what to do when the bus is already busy.
When GPIOBUS_WAIT wait is used, the calling thread will be put to sleep
until the bus became free.
With GPIOBUS_DONTWAIT the calling thread will receive EWOULDBLOCK right
away and then it can act upon.
This fixes the gpioiic(4) locking issues that arises when doing multiple
concurrent access on the bus.
At attach, print the SCL and SDA pin numbers.
Remove a stray blank line.
Remove the GPIOBUS locking from gpioiic_reset(), it is already called with
this lock held. This fixes a crash when you try to scan the iicbus with
i2c(8).
sys/systm.h must always come after sys/param.h.
Remove sys/types.h which should never be included together with sys/param.h.
Add sys/malloc.h for correctness even if it seems to don't be needed.
Remove more unused headers found by unusedinc (from bde@) and tested with a
universe build.
Reported by: bde
#gpio-cells property.
Add a new ofw_bus method (OFW_BUS_MAP_GPIOS()) that allows the GPIO
controller to implement its own mapping to deal with gpio-specifiers,
allowing the decoding of gpio-specifiers to be controller specific.
The default ofw_bus_map_gpios() decodes the linux standard (#gpio-cells =
<2>) and the FreeBSD standard (#gpio-cells = <3>).
It pass the gpio-specifier flag field to the children as an ivar variable so
they can act upon.
gpioled(4).
Tested on RPi and BBB (using the hardware I2C controller and gpioiic(4) for
the I2C tests). It was also verified for regressions on RSPRO (MIPS/ar71xx)
used as reference for a non OFW-based system.
Update the gpioled(4) and gpioiic(4) man pages with some details and
examples about the FDT/OFW support.
Some compatibility details pointed out by imp@ will follow in subsequent
commits.
Approved by: adrian (mentor, implicit)
describe GPIO bindings in the system.
Move the GPIOBUS lock macros to gpiobusvar.h as they are now shared between
the OFW and the non OFW versions of GPIO bus.
Export gpiobus_print_pins() so it can also be used on the OFW GPIO bus.
Approved by: adrian (mentor, implicit)
it can be overriden by its OFW/FDT version.
Give a chance for GPIO devices that implement the device_identify method to
attach.
Approved by: adrian (mentor)
