Use input buffer watermarks of TTYHOG-512 (high) and (high)*7/8
(low) instead of TTYHOG/2 (high) and TTYHOG/5 (low) to agree with
some drivers. 512 is magic and some things depended on TTYHOG/2
>= TTYHOG-512 to work; now they depend on the 512 magic not changing
and TTYHOG-512 being significantly larger than 0. This should be
handled in ttsetwater().
Separate the decision about whether to do input flow control from
doing it. ttyblock() now just starts input flow control (hardware
and/or software) and there is a new function ttyunblock() to stop
it. The decisions are the same except for the watermark changes
and allowing for input expansion for PARMRK.
When flushing input, try harder at first to send a start character
if required, but give up if the first attempt fails.
cy.c, rc.c, sio.c:
Simplify: let ttyinput() handle input flow control if it is not
being bypassed. Use ttyblock() to start flow control otherwise.
rc.c:
Use same input flow control test as elsewhere: test in a more
efficient order and start flow control at >= highwater instead of
at > highwater.
interface set at 57600 baud, and I found out the hard way that lpd doesn't
know about speeds greater than 38400, even though <sys/ttydev.h> also
permits 57600 and 115200 baud. Fix this by adding B57600 and B115200 to the
'bauds' table. (The Apple printer worked properly once I did this, BTW. :)
interface is no longer IFF_UP.
The test for IFF_UP in ifpromisc is only useful while enabling IFF_PROMISC
and the higher levels of the bpf code do not allow for the possibility of
failure while shutting down. This is a trivial change.
Also, fixes PR#522.
string as possible and return ENOMEM if the entire string cannot
be returned. This brings the routines in line with how the man
page says they work, and how the calling routines are expecting
them to work. This allows the dummy uname() routine in libc to
obtain the version string, since the kernel version string is
longer than that normally returned by the uname() routine.
This is 3/4 of the fix for PR# 462.
Reviewed by: Bruce Evans
umountable file systems, hung processes, or system panics:
- Some operations could return without decrementing the vnode
reference count.
- Some operations could leave the vnode locked.
- Generalize the /kern/rootdev & rrootdev files so that they
are no longer special cased in kernfs_lookup().
Note: procfs, fdescfs, and most of the other miscfs/* file systems
also suffer from the same type of problems and I will work on
fixing them one at a time.
BUS DEVICE RESET followed by BUS RESET failure recovery strategy including
the necesary renegotiation of sync/wide transfers after recovery completes.
Clean up debugging code to make it more finely selectable. Reset code
debugging is enabled for now so I can get more feedback on how this
code behaves in real life.
as is required to be POSIXLY_CORRECT and "right". I interpret
"referring to a directory" as being a directory or becoming a
directory. E.g., the trailing slashes in mkdir("/nonesuch/"),
rename("/tmp", /nonesuch/") and link("/tmp", "/root_can_like_dirs/")
are ignored because the target will become a directory if the
syscall succeeds. A trailing slash on a symlink causes the symlink
to be followed (this is a bug if the symlink doesn't point to a
directory; fix later).
queues for TIOCSETA[W]. Swapping an even number of times broke
the queue resource limits. This would have broken CRTSCTS flow
control if the clist slush list was used up.
Don'concatenate the queues for TIOCSETA[W] if one of the queues
has a resource limit of 0. Concatenation would cause a panic if
one of the queues is nonempty and the other is limited to length
0. This may have caused panics in PPPDISC.
Wake up readers after all transitions of ICANON. When ICANON is
turned off it is quite likely that characters will become available
to be read.
Reduce indentation near these changes.
1024 that used to remain on a line of its own after savecore completed
its job will be overwritten later in the /etc/rc process.
Reviewed by:
Submitted by: graichen@sirius.physik.fu-berlin.de (Thomas Graichen)
Obtained from:
on output below low water) and TS_SO_OCOMPLETE (sleep on output complete).
Most of the support for this has already been committed. Drivers should
call ttwwakeup() to handle wakeups whenever output is below low water
(and some output event causes this condition to be checked) or TS_BUSY is
cleared.
tty.c:
Fix the livelock in ttywait() properly by sleeping on output complete, not
on output below low water.
Use ttwwakeup() instead of separate select and output wakeups for all
wakeups of writers.
Add wakeups of writers for output flushes and carrier/clocal transitions.
Don't go to sleep in ttycheckoutq() if ttstart() reduces the queue to below
low water.
Use the timeout built into tsleep() in ttycheckoutq().
Optimize the select wakeup in ttwwakeup(). It seems reasonable to know
too much about the internals of tp->t_wsel now that the knowledge is
localised in tty.c.
FTP_PASSIVE_MODE. It would be really nice if we could standardise on
this name so that all tools (like ncftp) that offer passive/active
ftp selection would work seamlessly with one user environment variable
setting.
Running there you got any kind of strange errors from tar caused
by treating directories as tar files!
Fix it by adding new isfile(name) (check for reg. files) to simple fexists(name) calls.
pkg_manage silently dumps core, pkg_info claims about them to
stderr, which makes very difficult to find what directory cause it via
tons of pkg_info -a output. I found solution which covers both variants,
now pkg_info claims about missing files to stdout among valid output
with ERROR: prefix. It heals pkg_manage to not dump core and makes
easy to find errors in pkg_info -a output by simple /ERROR 'more' command.
Look at error return of kread() and stop on error.
Fix warning in kread() to not output "kvm_read:" twice.
Killed PCB cache misses stat as we no longer have it.
specially from Darryl Okahata. I've rewritten several URL to the proper
<url url="" name=""> tag. There is still room for improvement but it
should be closer to 2.0.5R now. I'll try to be faster for future updates...
Obtained from: Mail messages from the lists.
