VM_PHYSSEG_SPARSE depending on whether the physical address space is
densely or sparsely populated with memory. The effect of this
definition is to determine which of two implementations of
vm_page_array and PHYS_TO_VM_PAGE() is used. The legacy
implementation is obtained by defining VM_PHYSSEG_DENSE, and a new
implementation that trades off time for space is obtained by defining
VM_PHYSSEG_SPARSE. For now, all architectures except for ia64 and
sparc64 define VM_PHYSSEG_DENSE. Defining VM_PHYSSEG_SPARSE on ia64
allows the entirety of my Itanium 2's memory to be used. Previously,
only the first 1 GB could be used. Defining VM_PHYSSEG_SPARSE on
sparc64 allows USIIIi-based systems to boot without crashing.
This change is a combination of Nathan Whitehorn's patch and my own
work in perforce.
Discussed with: kmacy, marius, Nathan Whitehorn
PR: 112194
- Simplify the amount of work that has be done for each architecture by
pushing more of the truly MI code down into the PCI bus driver.
- Don't bind MSI-X indicies to IRQs so that we can allow a driver to map
multiple MSI-X messages into a single IRQ when handling a message
shortage.
The changes include:
- Add a new pcib_if method: PCIB_MAP_MSI() which is called by the PCI bus
to calculate the address and data values for a given MSI/MSI-X IRQ.
The x86 nexus drivers map this into a call to a new 'msi_map()' function
in msi.c that does the mapping.
- Retire the pcib_if method PCIB_REMAP_MSIX() and remove the 'index'
parameter from PCIB_ALLOC_MSIX(). MD code no longer has any knowledge
of the MSI-X index for a given MSI-X IRQ.
- The PCI bus driver now stores more MSI-X state in a child's ivars.
Specifically, it now stores an array of IRQs (called "message vectors" in
the code) that have associated address and data values, and a small
virtual version of the MSI-X table that specifies the message vector
that a given MSI-X table entry uses. Sparse mappings are permitted in
the virtual table.
- The PCI bus driver now configures the MSI and MSI-X address/data
registers directly via custom bus_setup_intr() and bus_teardown_intr()
methods. pci_setup_intr() invokes PCIB_MAP_MSI() to determine the
address and data values for a given message as needed. The MD code
no longer has to call back down into the PCI bus code to set these
values from the nexus' bus_setup_intr() handler.
- The PCI bus code provides a callout (pci_remap_msi_irq()) that the MD
code can call to force the PCI bus to re-invoke PCIB_MAP_MSI() to get
new values of the address and data fields for a given IRQ. The x86
MSI code uses this when an MSI IRQ is moved to a different CPU, requiring
a new value of the 'address' field.
- The x86 MSI psuedo-driver loses a lot of code, and in fact the separate
MSI/MSI-X pseudo-PICs are collapsed down into a single MSI PIC driver
since the only remaining diff between the two is a substring in a
bootverbose printf.
- The PCI bus driver will now restore MSI-X state (including programming
entries in the MSI-X table) on device resume.
- The interface for pci_remap_msix() has changed. Instead of accepting
indices for the allocated vectors, it accepts a mini-virtual table
(with a new length parameter). This table is an array of u_ints, where
each value specifies which allocated message vector to use for the
corresponding MSI-X message. A vector of 0 forces a message to not
have an associated IRQ. The device may choose to only use some of the
IRQs assigned, in which case the unused IRQs must be at the "end" and
will be released back to the system. This allows a driver to use the
same remap table for different shortage values. For example, if a driver
wants 4 messages, it can use the same remap table (which only uses the
first two messages) for the cases when it only gets 2 or 3 messages and
in the latter case the PCI bus will release the 3rd IRQ back to the
system.
MFC after: 1 month
vm.kmem_size_min. Useful when using ZFS to make sure that vm.kmem size will
be at least 256mb (for example) without forcing a particular value via vm.kmem_size.
Approved by: njl (mentor)
Reviewed by: alc
address ranges used by local and I/O APICs in the system. Some systems
also reserve these ranges as system resources via either PnPBIOS or
ACPI, so this device currently attaches after acpi0 and legacy0 so that
the system resources are given precedence.
variable to avoid invalid constraints in dead code. Use an array of
u_char's (inside a struct) instead of a char/short/int/long variable so
that the variable and its accesses can be spelled in the same way in all
cases and code doesn't need to be cloned just to hold the spelling
differences.
Fixed strict-aliasing errors in PCPU_SET() and in the amd64 PCPU_GET().
Cast to (void *) as in rev.1.37 of the i386 version where the errors
were fixed for the i386 PCPU_GET() only. It would be more correct to
copy to and from the temp. variable using memcpy(), but then an
ifdef tangle would be required to ensure using the builtin memcpy().
We depend on fairly aggressive optimization to put the temp. variable
only in a register despite it being copied using
*(type *)(void *)&anothertype and could depend on this when using
memcpy() too. This seems to work right even for -O0, but the -O0 case
has not been completely tested.
This change gives identical object code for all object files in LINT
on amd64 (except for one file with a __TIME__ stamp). For LINT on
i386 it gives unimportant differences in instruction order and padding
in a few object files. This was only tested for -O.
This change (actually a previous version of it) gives the following
reductions in the number of object files in LINT that fail to compile
with -O2 but without the -fno-strict-aliasing kludge:
- amd64: 29 (down from 211)
- i386: 36 (down from 47)
gcc-3.4.6 actually allows the invalid constraints that result from not
using the temp. variable, at least with -O[1-2], but gcc-3.3.3 crashes
on them and I don't want to depend on compiler bugs.
used by clock code, so don't export it to the world for machdep.c to
initialize. There is a minor problem initializing it before it is
used, since although clock initialization is split up so that parts
of it can be done early, the first part was never done early enough
to actually work. Split it up a bit more and do the first part as
late as possible to document the necessary order. The functions that
implement the split are still bogusly exported.
Cleaned up initialization of the i8254 clock hardware using the new
split. Actually initialize it early enough, and don't work around it
not being initialized in DELAY() when DELAY() is called early for
initialization of some console drivers.
This unfortunately moves a little more code before the early debugger
breakpoint so that it is harder to debug. The ordering of console and
related initialization is delicate because we want to do as little as
possible before the breakpoint, but must initialize a console.
- First off, device drivers really do need to know if they are allocating
MSI or MSI-X messages. MSI requires allocating powerof2() messages for
example where MSI-X does not. To address this, split out the MSI-X
support from pci_msi_count() and pci_alloc_msi() into new driver-visible
functions pci_msix_count() and pci_alloc_msix(). As a result,
pci_msi_count() now just returns a count of the max supported MSI
messages for the device, and pci_alloc_msi() only tries to allocate MSI
messages. To get a count of the max supported MSI-X messages, use
pci_msix_count(). To allocate MSI-X messages, use pci_alloc_msix().
pci_release_msi() still handles both MSI and MSI-X messages, however.
As a result of this change, drivers using the existing API will only
use MSI messages and will no longer try to use MSI-X messages.
- Because MSI-X allows for each message to have its own data and address
values (and thus does not require all of the messages to have their
MD vectors allocated as a group), some devices allow for "sparse" use
of MSI-X message slots. For example, if a device supports 8 messages
but the OS is only able to allocate 2 messages, the device may make the
best use of 2 IRQs if it enables the messages at slots 1 and 4 rather
than default of using the first N slots (or indicies) at 1 and 2. To
support this, add a new pci_remap_msix() function that a driver may call
after a successful pci_alloc_msix() (but before allocating any of the
SYS_RES_IRQ resources) to allow the allocated IRQ resources to be
assigned to different message indices. For example, from the earlier
example, after pci_alloc_msix() returned a value of 2, the driver would
call pci_remap_msix() passing in array of integers { 1, 4 } as the
new message indices to use. The rid's for the SYS_RES_IRQ resources
will always match the message indices. Thus, after the call to
pci_remap_msix() the driver would be able to access the first message
in slot 1 at SYS_RES_IRQ rid 1, and the second message at slot 4 at
SYS_RES_IRQ rid 4. Note that the message slots/indices are 1-based
rather than 0-based so that they will always correspond to the rid
values (SYS_RES_IRQ rid 0 is reserved for the legacy INTx interrupt).
To support this API, a new PCIB_REMAP_MSIX() method was added to the
pcib interface to change the message index for a single IRQ.
Tested by: scottl
MPLOCKED. The cleaning in rev.1.25 was supposed to have been undone
by rev.1.26, but 1.26 could never have actually affected asm files
since atomic.h is full of C declarations so including it in asm files
would just give syntax errors. The asm MPLOCKED is even less needed
than when misplaced definitions of it were first removed, and is now
unused in any asm file in the src tree except in anachronismns in
sys/i386/i386/support.s.
These functions are used a lot for mutexes, so this reduces the text
size of an average kernel by about 0.75%. This wasn't intended to
be a significant optimization, but it somehow increased the maximum
number of packets per second that can be transmitted by my bge hardware
from 320000 to 460000 (this benchmark is CPU-bound and remarkably
sensitive to changes in the text section).
Details: we would prefer to leave the result of the cmpxchg in %al,
but cannot tell gcc that it is there, so we have to convert it to an
integer register. We converted to %al, then to %[re]ax, but the
latter step is usually wasted since gcc usually only wants the condition
code and can recover it from %al just as easily as from %[re]ax. Let
gcc promote %al in the few cases where this is needed.
Nearby style fixes;
- let gcc manage the load of `res', and don't abuse `res' for a copy of `exp'
- don't echo `res's name in comments
- consistently spell the condition code as 'e' after comparison for equality
- don't hard-code %al anywhere except in constraints
- for the version that doesn't use cmpxchg, there is no requirement to use
%al anywhere, so don't hard-code it in the constraints either.
Style non-fix:
- for the versions that use cmpxchg, keep using "a" (was %[re]ax, now %al)
for the main output operand, although this is not required. The input
and output operands that use the "a" constraint are now decoupled, and
this makes things clearer except for the reason that the output register
is hard-coded. It is now just a hack to tell gcc that the input "a" has
been clobbered without increasing the number of operands.
passed by value (trap frames) as if they were in fact being passed by
reference. For better or worse, this incorrect behaviour is no longer
present in gcc 4.1. In this patch I convert all trapframe arguments to
be explicitly pass by reference. I also remove vm86_initflags, pushing
the very little work that it actually does up into vm86_prepcall.
Reviewed by: kan
Tested by: kan
of various scattered magic values.
- Pretty print the address of hardware watchpoints in 'show watch' rather
than just displaying hex.
- Expand address field width on amd64 for 64-bit pointers.
- Add a new apic_alloc_vectors() method to the local APIC support code
to allocate N contiguous IDT vectors (aligned on a M >= N boundary).
This function is used to allocate IDT vectors for a group of MSI
messages.
- Add MSI and MSI-X PICs. The PIC code here provides methods to manage
edge-triggered MSI messages as x86 interrupt sources. In addition to
the PIC methods, msi.c also includes methods to allocate and release
MSI and MSI-X messages. For x86, we allow for up to 128 different
MSI IRQs starting at IRQ 256 (IRQs 0-15 are reserved for ISA IRQs,
16-254 for APIC PCI IRQs, and IRQ 255 is reserved).
- Add pcib_(alloc|release)_msi[x]() methods to the MD x86 PCI bridge
drivers to bubble the request up to the nexus driver.
- Add pcib_(alloc|release)_msi[x]() methods to the x86 nexus drivers that
ask the MSI PIC code to allocate resources and IDT vectors.
MFC after: 2 months
of NKPT is no longer enough to run amd64 with 16G of RAM, as it
doesn't have space for mapping a kernel (16M kernel would require
additionally 8 page tables).
Fixed a syntax error for the (!__KERNEL && !__GNUCLIKE_ASM) case in
rev.1.36. Apparently, this case has never been reached even by lint.
Submitted by: stefanf
{amd64,i386}/include/profile.h:
In case the above case is actually reached, break it properly by
providing null support that will fail at link time instead of a stub
that gives wrong (null) profiling at runtime.
this used to be slightly cleaner than using ifdefs in a few places to
support both a.out and elf, but using it now just causes messes and
unportabilities. It seems to be impossible to implement the elf
HIDENAME() portably in cpp (since token pasting of "." and <name> is
invalid).
*/prof_machdep.c:
- Removed all uses of CNAME(). CNAME() is easy enough to use in pure
asm code, but using it in inline asm requires messy quoting. The
core pure asm code has been hacked on more and all uses of CNAME() in
it have already gone away. Just assume the elf convention here too.
- Removed now-uneeded include of <machine/asmacros.h>.
- Removed the workaround for a namespace conflict with this include.
profiling is configured but high resolution profiling is not configured.
Only functions in *.[Ss] called the stub, so efficiency was not
significantly affected.
(PICs) rather than interrupt sources. This allows interrupt controllers
with no interrupt pics (such as the 8259As when APIC is in use) to
participate in suspend/resume.
- Always register the 8259A PICs even if we don't use any of their pins.
- Explicitly reset the 8259As on resume on amd64 if 'device atpic' isn't
included.
- Add a "dummy" PIC for the local APIC on the BSP to reset the local APIC
on resume. This gets suspend/resume working with APIC on UP systems.
SMP still needs more work to bring the APs back to life.
The MFC after is tentative.
Tested by: anholt (i386)
Submitted by: Andrea Bittau <a.bittau at cs.ucl.ac.uk> (3)
MFC after: 1 week
Submitted by:
Reviewed by:
Approved by:
Obtained from:
MFC after:
Security:
Move the relocation definitions to the common elf header so that DTrace
can use them on one architecture targeted to a different one.
Add the additional ELF types defines in Sun's "Linker and Libraries"
manual.
WB (write-back) on x86 via control bits in PTEs and PDEs (including making
use of the PAT MSR). Changes include:
- A new pmap_mapdev_attr() function for amd64 and i386 which takes an
additional parameter (relative to pmap_mapdev()) specifying the cache
mode for this mapping. Note that on amd64 only WB mappings are done with
the direct map, all other modes result in a private mapping.
- pmap_mapdev() on i386 and amd64 now defaults to using UC (uncached)
mappings rather than WB. Previously we relied on the BIOS setting up
MTRR's to enforce memio regions being treated as UC. This might make
hw.cbb_start_memory unnecessary in some cases now for example.
- A new pmap_mapbios()/pmap_unmapbios() API has been added to allow places
that used pmap_mapdev() to map non-device memory (such as ACPI tables)
to do so using WB as before.
- A new pmap_change_attr() function for amd64 and i386 that changes the
caching mode for a range of KVA.
Reviewed by: alc
when the bit 22 is set to 1, CPUID with EAX=0 returns a maximum
value in EAX[7..0] of 3, when set to 0(default), CPUID with EAX=0
returns the number corresponding to the maximum standard function
supported. On my machine, BIOS sets the bit to 1 to make it to be
compatible with old OS, this causes dual-core Pentium-D (two
physical cores) to be identified as hyperthreading (two logical
cores) by function mp_topology().
POSIX (susv3) requires this, but it is unclear what should be inherited,
duplicating whole 387 stack for new thread seems to be unnecessary and
dangerous. Revert to previous code, force a new thread to be started with
clean FP state.
per page = effectively 12.19 bytes per pv entry after overheads).
Instead of using a shared UMA zone for 24 byte pv entries (two 8-byte tailq
nodes, a 4 byte pointer, and a 4 byte address), we allocate a page at a
time per process. This provides 336 pv entries per process (actually, per
pmap address space) and eliminates one of the 8-byte tailq entries since
we now can track per-process pv entries implicitly. The pointer to
the pmap can be eliminated by doing address arithmetic to find the metadata
on the page headers to find a single pointer shared by all 336 entries.
There is an 11-int bitmap for the freelist of those 336 entries.
This is mostly a mechanical conversion from amd64, except:
* i386 has to allocate kvm and map the pages, amd64 has them outside of kvm
* native word size is smaller, so bitmaps etc become 32 bit instead of 64
* no dump_add_page() etc stuff because they are in kvm always.
* various pmap internals tweaks because pmap uses direct map on amd64 but
on i386 it has to use sched_pin and temporary mappings.
Also, sysctl vm.pmap.pv_entry_max and vm.pmap.shpgperproc are now
dynamic sysctls. Like on amd64, i386 can now tune the pv entry limits
without a recompile or reboot.
This is important because of the following scenario. If you have a 1GB
file (262144 pages) mmap()ed into 50 processes, that requires 13 million
pv entries. At 24 bytes per pv entry, that is 314MB of ram and kvm, while
at 12 bytes it is 157MB. A 157MB saving is significant.
Test-run by: scottl (Thanks!)
Major differences:
* since there is no direct map region, there is no custom uma memory
allocator to modify to include its pages in the dumps.
* Various data entries are reduced from 64 bit to 32 bit to match the
native size.
dump_add_page() and dump_drop_page() are still present in case one wants to
arrange for arbitary pages to be dumped. This is of marginal use though
because libkvm+kgdb cannot address physical memory that isn't mapped into
kvm.
PCB in which the context of stopped CPUs is stored. To access this
PCB from KDB, we introduce a new define, called KDB_STOPPEDPCB. The
definition, when present, lives in <machine/kdb.h> and abstracts
where MD code saves the context. Define KDB_STOPPEDPCB on i386,
amd64, alpha and sparc64 in accordance to previous code.
- Throw out all of the logical APIC ID stuff. The Intel docs are somewhat
ambiguous, but it seems that the "flat" cluster model we are currently
using is only supported on Pentium and P6 family CPUs. The other
"hierarchy" cluster model that is supported on all Intel CPUs with
local APICs is severely underdocumented. For example, it's not clear
if the OS needs to glean the topology of the APIC hierarchy from
somewhere (neither ACPI nor MP Table include it) and setup the logical
clusters based on the physical hierarchy or not. Not only that, but on
certain Intel chipsets, even though there were 4 CPUs in a logical
cluster, all the interrupts were only sent to one CPU anyway.
- We now bind interrupts to individual CPUs using physical addressing via
the local APIC IDs. This code has also moved out of the ioapic PIC
driver and into the common interrupt source code so that it can be
shared with MSI interrupt sources since MSI is addressed to APICs the
same way that I/O APIC pins are.
- Interrupt source classes grow a new method pic_assign_cpu() to bind an
interrupt source to a specific local APIC ID.
- The SMP code now tells the interrupt code which CPUs are avaiable to
handle interrupts in a simpler and more intuitive manner. For one thing,
it means we could now choose to not route interrupts to HT cores if we
wanted to (this code is currently in place in fact, but under an #if 0
for now).
- For now we simply do static round-robin of IRQs to CPUs when the first
interrupt handler just as before, with the change that IRQs are now
bound to individual CPUs rather than groups of up to 4 CPUs.
- Because the IRQ to CPU mapping has now been moved up a layer, it would
be easier to manage this mapping from higher levels. For example, we
could allow drivers to specify a CPU affinity map for their interrupts,
or we could allow a userland tool to bind IRQs to specific CPUs.
The MFC is tentative, but I want to see if this fixes problems some folks
had with UP APIC kernels on 6.0 on SMP machines (an SMP kernel would work
fine, but a UP APIC kernel (such as GENERIC in RELENG_6) would lose
interrupts).
MFC after: 1 week
param.h. Per request, I've placed these just after the
_NO_NAMESPACE_POLLUTION ifndef. I've not renamed anything yet, but
may since we don't need the __.
Submitted by: bde, jhb, scottl, many others.
passing a pointer to an opaque clockframe structure and requiring the
MD code to supply CLKF_FOO() macros to extract needed values out of the
opaque structure, just pass the needed values directly. In practice this
means passing the pair (usermode, pc) to hardclock() and profclock() and
passing the boolean (usermode) to hardclock_cpu() and hardclock_process().
Other details:
- Axe clockframe and CLKF_FOO() macros on all architectures. Basically,
all the archs were taking a trapframe and converting it into a clockframe
one way or another. Now they can just extract the PC and usermode values
directly out of the trapframe and pass it to fooclock().
- Renamed hardclock_process() to hardclock_cpu() as the latter is more
accurate.
- On Alpha, we now run profclock() at hz (profhz == hz) rather than at
the slower stathz.
- On Alpha, for the TurboLaser machines that don't have an 8254
timecounter, call hardclock() directly. This removes an extra
conditional check from every clock interrupt on Alpha on the BSP.
There is probably room for even further pruning here by changing Alpha
to use the simplified timecounter we use on x86 with the lapic timer
since we don't get interrupts from the 8254 on Alpha anyway.
- On x86, clkintr() shouldn't ever be called now unless using_lapic_timer
is false, so add a KASSERT() to that affect and remove a condition
to slightly optimize the non-lapic case.
- Change prototypeof arm_handler_execute() so that it's first arg is a
trapframe pointer rather than a void pointer for clarity.
- Use KCOUNT macro in profclock() to lookup the kernel profiling bucket.
Tested on: alpha, amd64, arm, i386, ia64, sparc64
Reviewed by: bde (mostly)
- Move vtophys() macros next to vtopte() where vtopte() exists to match
comments above vtopte().
- Remove references to the alternate address space in the comment above
vtopte(). amd64 never had the alternate address space, and i386 lost it
prior to PAE support being added.
- s/entires/entries/ in comments.
Reviewed by: alc
MACHINE_ARCH and MACHINE). Their purpose was to be able to test
in cpp(1), but cpp(1) only understands integer type expressions.
Using such unsupported expressions introduced a number of subtle
bugs, which were discovered by compiling with -Wundef.
rather than embedding it in the intrframe as if_vec. This reduces diffs
with amd64 somewhat.
- Remove cf_vec from clockframe (it wasn't used anyway) and stop pushing
dummy vector arguments for ipi_bitmap_handler() and lapic_handle_timer()
since clockframe == trapframe now.
- Fix ddb to handle stack traces across interrupt entry points that just
have a trapframe on their stack and not a trapframe + vector.
- Change intr_execute_handlers() to take a trapframe rather than an
intrframe pointer.
- Change lapic_handle_intr() and atpic_handle_intr() to take a vector and
trapframe rather than an intrframe.
- GC struct intrframe now that nothing uses it anymore.
- GC CLOCK_TO_TRAPFRAME() and INTR_TO_TRAPFRAME().
Reviewed by: bde
Requested by: peter
ipi_nmi_handler() and into a new cpustop_handler() function. Change
the Xcpustop IPI_STOP handler to call this function instead of
duplicating all the same logic in assembly.
- EOI the local APIC for the lapic timer interrupt in C rather than
assembly.
- Bump the lazypmap IPI counter if COUNT_IPIS is defined in C rather than
assembly.
- Add a new SET_KERNEL_SREGS macro that sets up %ds and %es to point to
kernel data and %fs to point to per-CPU data and use the new macro
in several kernel entry points including trap and interrupt handlers.
- Convert the IPI_STOP handler Xcpustop to push a standard trap frame
rather than an application frame.
- Make the TRAP() macro private to exception.s since it is only used
there.
- Move the PCPU_*() macros in asmacros.h out of the middle of the
profiling macros.
Reviewed by: bde
Requested by: bde (4, 5)
during SMP startup. We haven't had any issues with starting up the APs
on i386 in quite a while now which is all this code is really useful for.
If someone ever does really need it they can always dig it up out of the
attic.
The following repo-copies were made (by Mark Murray):
sys/i386/isa/spkr.c -> sys/dev/speaker/spkr.c
sys/i386/include/speaker.h -> sys/dev/speaker/speaker.h
share/man/man4/man4.i386/spkr.4 -> share/man/man4/spkr.4
nearly identical to wintel/ia32, with a couple of tweaks. Since it is
so similar to ia32, it is optionally added to a i386 kernel. This
port is preliminary, but seems to work well. Further improvements
will improve the interaction with syscons(4), port Linux nforce driver
and future versions of the xbox.
This supports the 64MB and 128MB boxes. You'll need the most recent
CVS version of Cromwell (the Linux BIOS for the XBOX) to boot.
Rink will be maintaining this port, and is interested in feedback.
He's setup a website http://xbox-bsd.nl to report the latest
developments.
Any silly mistakes are my fault.
Submitted by: Rink P.W. Springer rink at stack dot nl and
Ed Schouten ed at fxq dot nl
source is first enabled similar to how intr_event's now allocate ithreads
on-demand. Previously, we would map IDT vectors 1:1 to IRQs. Since we
only have 191 available IDT vectors for I/O interrupts, this limited us
to only supporting IRQs 0-190 corresponding to the first 190 I/O APIC
intpins. On many machines, however, each PCI-X bus has its own APIC even
though it only has 1 or 2 devices, thus, we were reserving between 24 and
32 IRQs just for 1 or 2 devices and thus 24 or 32 IDT vectors. With this
change, a machine with 100 IRQs but only 5 in use will only use up 5 IDT
vectors. Also, this change provides an API (apic_alloc_vector() and
apic_free_vector()) that will allow a future MSI interrupt source driver to
request IDT vectors for use by MSI interrupts on x86 machines.
Tested on: amd64, i386
and increase flexibility to allow various different approaches to be tried
in the future.
- Split struct ithd up into two pieces. struct intr_event holds the list
of interrupt handlers associated with interrupt sources.
struct intr_thread contains the data relative to an interrupt thread.
Currently we still provide a 1:1 relationship of events to threads
with the exception that events only have an associated thread if there
is at least one threaded interrupt handler attached to the event. This
means that on x86 we no longer have 4 bazillion interrupt threads with
no handlers. It also means that interrupt events with only INTR_FAST
handlers no longer have an associated thread either.
- Renamed struct intrhand to struct intr_handler to follow the struct
intr_foo naming convention. This did require renaming the powerpc
MD struct intr_handler to struct ppc_intr_handler.
- INTR_FAST no longer implies INTR_EXCL on all architectures except for
powerpc. This means that multiple INTR_FAST handlers can attach to the
same interrupt and that INTR_FAST and non-INTR_FAST handlers can attach
to the same interrupt. Sharing INTR_FAST handlers may not always be
desirable, but having sio(4) and uhci(4) fight over an IRQ isn't fun
either. Drivers can always still use INTR_EXCL to ask for an interrupt
exclusively. The way this sharing works is that when an interrupt
comes in, all the INTR_FAST handlers are executed first, and if any
threaded handlers exist, the interrupt thread is scheduled afterwards.
This type of layout also makes it possible to investigate using interrupt
filters ala OS X where the filter determines whether or not its companion
threaded handler should run.
- Aside from the INTR_FAST changes above, the impact on MD interrupt code
is mostly just 's/ithread/intr_event/'.
- A new MI ddb command 'show intrs' walks the list of interrupt events
dumping their state. It also has a '/v' verbose switch which dumps
info about all of the handlers attached to each event.
- We currently don't destroy an interrupt thread when the last threaded
handler is removed because it would suck for things like ppbus(8)'s
braindead behavior. The code is present, though, it is just under
#if 0 for now.
- Move the code to actually execute the threaded handlers for an interrrupt
event into a separate function so that ithread_loop() becomes more
readable. Previously this code was all in the middle of ithread_loop()
and indented halfway across the screen.
- Made struct intr_thread private to kern_intr.c and replaced td_ithd
with a thread private flag TDP_ITHREAD.
- In statclock, check curthread against idlethread directly rather than
curthread's proc against idlethread's proc. (Not really related to intr
changes)
Tested on: alpha, amd64, i386, sparc64
Tested on: arm, ia64 (older version of patch by cognet and marcel)
IPI_STOP IPIs.
- Change the i386 and amd64 MD IPI code to send an NMI if STOP_NMI is
enabled if an attempt is made to send an IPI_STOP IPI. If the kernel
option is enabled, there is also a sysctl to change the behavior at
runtime (debug.stop_cpus_with_nmi which defaults to enabled). This
includes removing stop_cpus_nmi() and making ipi_nmi_selected() a
private function for i386 and amd64.
- Fix ipi_all(), ipi_all_but_self(), and ipi_self() on i386 and amd64 to
properly handle bitmapped IPIs as well as IPI_STOP IPIs when STOP_NMI is
enabled.
- Fix ipi_nmi_handler() to execute the restart function on the first CPU
that is restarted making use of atomic_readandclear() rather than
assuming that the BSP is always included in the set of restarted CPUs.
Also, the NMI handler didn't clear the function pointer meaning that
subsequent stop and restarts could execute the function again.
- Define a new macro HAVE_STOPPEDPCBS on i386 and amd64 to control the use
of stoppedpcbs[] and always enable it for i386 and amd64 instead of
being dependent on KDB_STOP_NMI. It works fine in both the NMI and
non-NMI cases.
- Add newer CPUID definitions for future use.
Many thanks to Mike Tancsa <mike at sentex dot net> for providing test
cases for Intel Pentium D and AMD Athlon 64 X2.
Approved by: anholt (mentor)
can be enabled by enabling COUNT_IPIS in smptests.h. When enabled, each
CPU provides an interrupt counter for nearly all of the IPIs it receives
(IPI_STOP currently doesn't have a counter) that can be examined using
vmstat -i, etc.
MFC after: 3 days
Requested by: rwatson
variable and returns the previous value of the variable.
Tested on: i386, alpha, sparc64, arm (cognet)
Reviewed by: arch@
Submitted by: cognet (arm)
MFC after: 1 week
constraint is actually only allowed for register operands. Instead, use
separate input and output memory constraints.
Education from: alc
Reviewed by: alc
Tested on: i386, alpha
MFC after: 1 week
and reloading it in i386_extend_pcb() rather than trying to force a context
switch to reload the TSS via the TDF_NEEDRESCHED flag. Optimizations to
avoid calling cpu_switch() when the new thread was identical to the old
thread defeated the attempt to force a TSS reload. Explicitly loading the
new TSS is what we really want to do anyway.
PR: i386/84842
Reported by: Alexander Best arundel at h3c dot de
MFC after: 1 week
Reviewed by: bde (mostly)
it to __MINSIGSTKSZ. Define MINSIGSTKSZ in <sys/signal.h>.
This is done in order to use MINSIGSTKSZ for the macro PTHREAD_STACK_MIN
in <pthread.h> (soon <limits.h>) without having to include the whole
<sys/signal.h> header.
Discussed with: bde
and return a printable representation.
This fixes recognition of the PC Engines WRAP and improves the
recognition of the Soekris boards (Bios version can now be
seen in the dmesg output for instance).
Also, add watchdog support for PCM-582x platforms.
Submitted by: Adrian Steinmann <ast@marabu.ch>
Slightly changed by: phk
PR: 81360
