in half because of reports that under heavy load the kernel could
exhaust its memory pool. The limit is now (desiredvnodes * 4)
rather than (desiredvnodes * 8), so it will still scale with
larger systems, just not as quickly.
Sponsored by: DARPA & NAI Labs.
not have hit the disk and the dependencies cannot be unrolled.
In this case, the system will mark the buffer as dirty again so
that the write can be retried in the future. When the write
succeeds or the system gives up on the buffer and marks it as
invalid (B_INVAL), the dependencies will be cleared.
Sponsored by: DARPA & NAI Labs.
checks permit policy modules to augment the system policy for permitting
kld operations. This permits policies to limit access to kld operations
based on credential (and other) properties, as well as to perform checks
on the kld being loaded (integrity, etc).
Approved by: re
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
leader wasn't exiting during a fork; instead, do remember to release
the lock avoiding lock order reversals and recursion panic.
Reported by: "Joel M. Baldwin" <qumqats@outel.org>
after configure() has run. Only create the device if ofwcons is the
highest priority console. Make a dev alias with the same name as the
firmware output-device property.
also add rusage time in thread mailbox.
2. Minor change for thread limit code in thread_user_enter(),
fix typo in kse_release() last I committed.
Reviewed by: deischen, mini
- Clear the PG_WRITEABLE flag in pmap_changebit() if write access is
being removed. Return immediately if write access is being removed and
PG_WRITEABLE is already clear.
Note: For efficiency, pmap_changebit() should be replaced by a function
similar to sparc64's pmap_clear_write().
- Clear the PG_WRITEABLE flag in pmap_page_protect() if write access is
being removed. Return immediately if write access is being removed and
PG_WRITEABLE is already clear.
so that it can be reused elsewhere (there is a number of places
where it can be useful). This also trims some 200 lines from
the body of ip_output(), which helps readability a bit.
(This change was discussed a few weeks ago on the mailing lists,
Julian agreed, silence from others. It is not a functional change,
so i expect it to be ok to commit it now but i am happy to back it
out if there are objections).
While at it, fix some function headers and replace m_copy() with
m_copypacket() where applicable.
MFC after: 1 week
2. Avoid referencing bcopy() and bzero(), since they may not be in
scope.
Request by: bde (1)
Submitted by: wollman (2)
Reviewed by: archie, bde
PR: 43270
Replace m_copy() with m_copypacket() where applicable.
Replace "if (a.s_addr ...)" with "if (a.s_addr != INADDR_ANY ...)"
to make it clear what the code means.
While at it, fix some function headers and remove 'register' from
variable declarations.
MFC after: 3 days
trigger a breakpoint with this chip.
- Fiddle the right bits in the cn input and output routines to disable port
interrupts and enable visibility of the masked interrupt status bits.
- Register a shutdown final event handler to put the chip back in the mode
that the prom expects.
kern.threads.max_threads_per_proc
kern.threads.max_groups_per_proc
2.Temporary disable borrower thread stash itself as
owner thread's spare thread in thread_exit(). there
is a race between owner thread and borrow thread:
an owner thread may allocate a spare thread as this:
if (td->td_standin == NULL)
td->standin = thread_alloc();
but thread_alloc() can block the thread, then a borrower
thread would possible stash it self as owner's spare
thread in thread_exit(), after owner is resumed, result
is a thread leak in kernel, double check in owner can
avoid the race, but it may be ugly and not worth to do.
sysconf.c:
Use 'break' rather than 'goto yesno' in sysconf.c so that we report a '0'
return value from the kernel sysctl.
vfs_aio.c:
Make aio reset its configuration parameters to -1 after unloading
instead of 0.
posix4_mib.c:
Initialize the aio configuration parameters to -1
to indicate that it is not loaded.
Add a facility (p31b_iscfg()) to determine if a posix4 facility has been
initialized to avoid having to re-order the SYSINITs.
Use p31b_iscfg() to determine if aio has had a chance to run yet which
is likely if it is compiled into the kernel and avoid spamming its
values.
Introduce a macro P31B_VALID() instead of doing the same comparison over
and over.
posix4.h:
Prototype p31b_iscfg().
