Allow guests to set the RTC bit in the ACPI PM control register.
This eliminates an annoying (and harmless) Linux kernel boot message.
PR: 244721
Submitted by: Jose Luis Duran
MFC after: 1 week
Add an implementatation of the 'Virtual Machine Generation ID' spec to
Bhyve. The spec provides a randomly generated GUID (at bhyve start) in
device memory, along with an ACPI device with _CID VM_Gen_Counter and ADDR
evaluating to a Package pointing at that GUID.
A GPE is defined which Notifies the ACPI Device when the generation changes
(such as when a snapshot is rolled back). At this time, Bhyve does not
support snapshotting, so the GPE is never actually raised.
Suggested by: rpokala
Discussed with: grehan
Differential Revision: https://reviews.freebsd.org/D23165
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
No functional change intended.
change 0 means success and non-zero means failure.
This also helps to eliminate VMEXIT_POWEROFF and VMEXIT_RESET as return values
from VM-exit handlers.
CR: D480
Reviewed by: grehan, jhb
the legacy 8259A PICs.
- Implement an ICH-comptabile PCI interrupt router on the lpc device with
8 steerable pins configured via config space access to byte-wide
registers at 0x60-63 and 0x68-6b.
- For each configured PCI INTx interrupt, route it to both an I/O APIC
pin and a PCI interrupt router pin. When a PCI INTx interrupt is
asserted, ensure that both pins are asserted.
- Provide an initial routing of PCI interrupt router (PIRQ) pins to
8259A pins (ISA IRQs) and initialize the interrupt line config register
for the corresponding PCI function with the ISA IRQ as this matches
existing hardware.
- Add a global _PIC method for OSPM to select the desired interrupt routing
configuration.
- Update the _PRT methods for PCI bridges to provide both APIC and legacy
PRT tables and return the appropriate table based on the configured
routing configuration. Note that if the lpc device is not configured, no
routing information is provided.
- When the lpc device is enabled, provide ACPI PCI link devices corresponding
to each PIRQ pin.
- Add a VMM ioctl to adjust the trigger mode (edge vs level) for 8259A
pins via the ELCR.
- Mark the power management SCI as level triggered.
- Don't hardcode the number of elements in Packages in the source for
the DSDT. iasl(8) will fill in the actual number of elements, and
this makes it simpler to generate a Package with a variable number of
elements.
Reviewed by: tycho
LPC devices. Among other things, the LPC serial ports now appear as
ACPI devices.
- Move the info for the top-level PCI bus into the PCI emulation code and
add ResourceProducer entries for the memory ranges decoded by the bus
for memory BARs.
- Add a framework to allow each PCI emulation driver to optionally write
an entry into the DSDT under the \_SB_.PCI0 namespace. The LPC driver
uses this to write a node for the LPC bus (\_SB_.PCI0.ISA).
- Add a linker set to allow any LPC devices to write entries into the
DSDT below the LPC node.
- Move the existing DSDT block for the RTC to the RTC driver.
- Add DSDT nodes for the AT PIC, the 8254 ISA timer, and the LPC UART
devices.
- Add a "SuperIO" device under the LPC node to claim "system resources"
aling with a linker set to allow various drivers to add IO or memory
ranges that should be claimed as a system resource.
- Add system resource entries for the extended RTC IO range, the registers
used for ACPI power management, the ELCR, PCI interrupt routing register,
and post data register.
- Add various helper routines for generating DSDT entries.
Reviewed by: neel (earlier version)
to SIGTERM when ACPI is enabled. Sending SIGTERM to the hypervisor when an
ACPI-aware OS is running will now trigger a soft-off allowing for a graceful
shutdown of the guest.
- Move constants for ACPI-related registers to acpi.h.
- Implement an SMI_CMD register with commands to enable and disable ACPI.
Currently the only change when ACPI is enabled is to enable the virtual
power button via SIGTERM.
- Implement a fixed-feature power button when ACPI is enabled by asserting
PWRBTN_STS in PM1_EVT when SIGTERM is received.
- Add support for EVFILT_SIGNAL events to mevent.
- Implement support for the ACPI system command interrupt (SCI) and assert
it when needed based on the values in PM1_EVT. Mark the SCI as active-low
and level triggered in the MADT and MP Table.
- Mark PCI interrupts in the MP Table as active-low in addition to level
triggered.
Reviewed by: neel
- Implement the PM1_EVT and PM1_CTL registers required by ACPI.
The PM1_EVT register is mostly a dummy as bhyve doesn't support any
of the hardware-initiated events. The only bit of PM1_CNT that is
implemented are the sleep request bits (SPL_EN and SLP_TYP) which
request a graceful power off for S5. In particular, for S5, bhyve
exits with a non-zero value which terminates the loop in vmrun.sh.
- Emulate the Reset Control register at I/O port 0xcf9 and advertise
it as the reset register via ACPI.
- Advertise an _S5 package.
- Extend the in/out interface to allow an in/out handler to request
that the hypervisor trigger a reset or power-off.
- While here, note that all vCPUs in a guest support C1 ("hlt").
Reviewed by: neel (earlier version)
