This will help Jenkins dedupe 9 warnings between the static build and
the module build of ipsec(4).
Missed in SRCTOP conversion in r314651.
MFC with: r314651
Sponsored by: Dell EMC Isilon
The ccr(4) driver supports use of the crypto accelerator engine on
Chelsio T6 NICs in "lookaside" mode via the opencrypto framework.
Currently, the driver supports AES-CBC, AES-CTR, AES-GCM, and AES-XTS
cipher algorithms as well as the SHA1-HMAC, SHA2-256-HMAC, SHA2-384-HMAC,
and SHA2-512-HMAC authentication algorithms. The driver also supports
chaining one of AES-CBC, AES-CTR, or AES-XTS with an authentication
algorithm for encrypt-then-authenticate operations.
Note that this driver is still under active development and testing and
may not yet be ready for production use. It does pass the tests in
tests/sys/opencrypto with the exception that the AES-GCM implementation
in the driver does not yet support requests with a zero byte payload.
To use this driver currently, the "uwire" configuration must be used
along with explicitly enabling support for lookaside crypto capabilities
in the cxgbe(4) driver. These can be done by setting the following
tunables before loading the cxgbe(4) driver:
hw.cxgbe.config_file=uwire
hw.cxgbe.cryptocaps_allowed=-1
MFC after: 1 month
Relnotes: yes
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D10763
2. Use sysctls for TRACE_LRO_CNT and TRACE_TSO_PKT_LEN
3. remove unused mtx tx_lock
4. bind taskqueue kernel thread to the appropriate cpu core
5. when tx_ring is full, stop further transmits till at least 1/16th of the Tx Ring is empty. In our case 1K entries. Also if there are rx_pkts to process, put the taskqueue thread to sleep for 100ms, before enabling interrupts.
6. Use rx_pkt_threshold of 128.
MFC after:3 days
* This adds iwm_mvm_rm_sta(), which will be used to tear down firmware
state for better/cleaner iwm_newstate() handling.
* Makes iwm_enable_txq() and iwm_mvm_flush_tx_path() non-static, add
the declarations to if_iwm_util.h for now.
Obtained from: dragonflybsd.git 85d1c6190c4c3564b1a347f253e823aa95c202b2
For GEN1 Hyper-V, vmbus is attached to pcib0, which contains the
resources for PCI passthrough and SR-IOV. There is no
acpi_syscontainer0 on GEN1 Hyper-V.
For GEN2 Hyper-V, vmbus is attached to acpi_syscontainer0, which
contains the resources for PCI passthrough and SR-IOV. There is
no pcib0 on GEN2 Hyper-V.
The ACPI VMBUS device now only holds its _CRS, which is empty as
of this commit; its existence is mainly for upward compatibility.
Device tree structure is suggested by jhb@.
Tested-by: dexuan@
Collabrated-wth: dexuan@
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D10565
the TOE. For now this capability is always enabled in kernels with
options RATELIMIT. t4_tom will check if_capenable once the base driver
gets code to support rate limiting for any socket (TOE or not).
This was tested with iperf3 and netperf ToT as they already support
SO_MAX_PACING_RATE sockopt. There is a bug in firmwares prior to
1.16.45.0 that affects the BSD driver only and results in rate-limiting
at an incorrect rate. This will resolve by itself as soon as 1.16.45.0
or later firmware shows up in the driver.
Relnotes: Yes
Sponsored by: Chelsio Communications
- Create a new file, t4_sched.c, and move all of the code related to
traffic management from t4_main.c and t4_sge.c to this file.
- Track both Channel Rate Limiter (ch_rl) and Class Rate Limiter (cl_rl)
parameters in the PF driver.
- Initialize all the cl_rl limiters with somewhat arbitrary default
rates and provide routines to update them on the fly.
- Provide routines to reserve and release traffic classes.
MFC after: 1 month
Sponsored by: Chelsio Communications
patm(4) devices.
Maintaining an address family and framework has real costs when we make
infrastructure improvements. In the case of NATM we support no devices
manufactured in the last 20 years and some will not even work in modern
motherboards (some newer devices that patm(4) could be updated to
support apparently exist, but we do not currently have support).
With this change, support remains for some netgraph modules that don't
require NATM support code. It is unclear if all these should remain,
though ng_atmllc certainly stands alone.
Note well: FreeBSD 11 supports NATM and will continue to do so until at
least September 30, 2021. Improvements to the code in FreeBSD 11 are
certainly welcome.
Reviewed by: philip
Approved by: harti
FDC_DEBUG is not referenced in any c or header files but traces of it
still remain in other files.
PR: 105608
Reported by: Eugene Grosbein <ports AT grosbein DOT net>
Reviewed by: imp
Approved by: bcr (mentor)
MFC after: 7 days
Differential Revision: https://reviews.freebsd.org/D10303
- Move all bitmap related functions from bitops.h to bitmap.h, similar
to what Linux does.
- Apply some minor code cleanup and simplifications to optimize the
generated code when using static inline functions.
- Implement the following list of bitmap functions which are needed by
drm-next and ibcore:
- bitmap_find_next_zero_area_off()
- bitmap_find_next_zero_area()
- bitmap_or()
- bitmap_and()
- bitmap_xor()
- Add missing include directives to the qlnxe driver
(davidcs@ has been notified)
MFC after: 1 week
Sponsored by: Mellanox Technologies
DTrace includes assym.s, to build this we build assym.o, however
this is unneeded as assym.s only contains macros.
Remove the need to build this by removing it from OBJS, but keep assym.s
in the module dependencies via DPSRCS.
This fixes the build when there is no assembler, e.g. on arm64 without
the external binutils.
Submitted by: andrew
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D10041
The module is designed for modification of a packets of any protocols.
For now it implements only TCP MSS modification. It adds the external
action handler for "tcp-setmss" action.
A rule with tcp-setmss action does additional check for protocol and
TCP flags. If SYN flag is present, it parses TCP options and modifies
MSS option if its value is greater than configured value in the rule.
Then it adjustes TCP checksum if needed. After handling the search
continues with the next rule.
Obtained from: Yandex LLC
MFC after: 2 weeks
Relnotes: yes
Sponsored by: Yandex LLC
No objection from: #network
Differential Revision: https://reviews.freebsd.org/D10150
The goal of this work is to remove the explicit dependency for ctl(4)
on iscsi(4), so end-users without iscsi(4) support in the kernel can
use ctl(4) for its other functions.
This allows those without iscsi(4) support built into the kernel to use
ctl(4) as a test mechanism. As a sidenote, this was possible around the
10.0-RELEASE period, but made impossible for end-users without iscsi(4)
between 10.0-RELEASE and 11.0-RELEASE.
Automatically load cfiscsi(4) from ctladm(8) and ctld(8) for backwards
compatibility with previously releases. The automatic loading feature is
compiled into the beforementioned tools if MK_ISCSI == yes when building
world.
Add a manpage for cfiscsi(4) and refer to it in ctl(4).
Differential Revision: D10099
MFC after: 2 months
Relnotes: yes
Reviewed by: mav, trasz
Sponsored by: Dell EMC Isilon
instrument security event auditing rather than relying on conventional BSM
trail files or audit pipes:
- Add a set of per-event 'commit' probes, which provide access to
particular auditable events at the time of commit in system-call return.
These probes gain access to audit data via the in-kernel audit_record
data structure, providing convenient access to system-call arguments and
return values in a single probe.
- Add a set of per-event 'bsm' probes, which provide access to particular
auditable events at the time of BSM record generation in the audit
worker thread. These probes have access to the in-kernel audit_record
data structure and BSM representation as would be written to a trail
file or audit pipe -- i.e., asynchronously in the audit worker thread.
DTrace probe arguments consist of the name of the audit event (to support
future mechanisms of instrumenting multiple events via a single probe --
e.g., using classes), a pointer to the in-kernel audit record, and an
optional pointer to the BSM data and its length. For human convenience,
upper-case audit event names (AUE_...) are converted to lower case in
DTrace.
DTrace scripts can now cause additional audit-based data to be collected
on system calls, and inspect internal and BSM representations of the data.
They do not affect data captured in the audit trail or audit pipes
configured in the system. auditd(8) must be configured and running in
order to provide a database of event information, as well as other audit
configuration parameters (e.g., to capture command-line arguments or
environmental variables) for the provider to operate.
Reviewed by: gnn, jonathan, markj
Sponsored by: DARPA, AFRL
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D10149
the default partition, eMMC v4.41 and later devices can additionally
provide up to:
1 enhanced user data area partition
2 boot partitions
1 RPMB (Replay Protected Memory Block) partition
4 general purpose partitions (optionally with a enhanced or extended
attribute)
Of these "partitions", only the enhanced user data area one actually
slices the user data area partition and, thus, gets handled with the
help of geom_flashmap(4). The other types of partitions have address
space independent from the default partition and need to be switched
to via CMD6 (SWITCH), i. e. constitute a set of additional "disks".
The second kind of these "partitions" doesn't fit that well into the
design of mmc(4) and mmcsd(4). I've decided to let mmcsd(4) hook all
of these "partitions" up as disk(9)'s (except for the RPMB partition
as it didn't seem to make much sense to be able to put a file-system
there and may require authentication; therefore, RPMB partitions are
solely accessible via the newly added IOCTL interface currently; see
also below). This approach for one resulted in cleaner code. Second,
it retains the notion of mmcsd(4) children corresponding to a single
physical device each. With the addition of some layering violations,
it also would have been possible for mmc(4) to add separate mmcsd(4)
instances with one disk each for all of these "partitions", however.
Still, both mmc(4) and mmcsd(4) share some common code now e. g. for
issuing CMD6, which has been factored out into mmc_subr.c.
Besides simply subdividing eMMC devices, some Intel NUCs having UEFI
code in the boot partitions etc., another use case for the partition
support is the activation of pseudo-SLC mode, which manufacturers of
eMMC chips typically associate with the enhanced user data area and/
or the enhanced attribute of general purpose partitions.
CAVEAT EMPTOR: Partitioning eMMC devices is a one-time operation.
- Now that properly issuing CMD6 is crucial (so data isn't written to
the wrong partition for example), make a step into the direction of
correctly handling the timeout for these commands in the MMC layer.
Also, do a SEND_STATUS when CMD6 is invoked with an R1B response as
recommended by relevant specifications. However, quite some work is
left to be done in this regard; all other R1B-type commands done by
the MMC layer also should be followed by a SEND_STATUS (CMD13), the
erase timeout calculations/handling as documented in specifications
are entirely ignored so far, the MMC layer doesn't provide timeouts
applicable up to the bridge drivers and at least sdhci(4) currently
is hardcoding 1 s as timeout for all command types unconditionally.
Let alone already available return codes often not being checked in
the MMC layer ...
- Add an IOCTL interface to mmcsd(4); this is sufficiently compatible
with Linux so that the GNU mmc-utils can be ported to and used with
FreeBSD (note that due to the remaining deficiencies outlined above
SANITIZE operations issued by/with `mmc` currently most likely will
fail). These latter will be added to ports as sysutils/mmc-utils in
a bit. Among others, the `mmc` tool of the GNU mmc-utils allows for
partitioning eMMC devices (tested working).
- For devices following the eMMC specification v4.41 or later, year 0
is 2013 rather than 1997; so correct this for assembling the device
ID string properly.
- Let mmcsd.ko depend on mmc.ko. Additionally, bump MMC_VERSION as at
least for some of the above a matching pair is required.
- In the ACPI front-end of sdhci(4) describe the Intel eMMC and SDXC
controllers as such in order to match the PCI one.
Additionally, in the entry for the 80860F14 SDXC controller remove
the eMMC-only SDHCI_QUIRK_INTEL_POWER_UP_RESET.
OKed by: imp
Submitted by: ian (mmc_switch_status() implementation)
They cannot be used anymore with the userland bits we provide.
Furthermore, their KMS versions support the same hardware.
Submitted by: dumbbell
Reviewed by: emaste, manu
Sponsored by: AsiaBSDCon
Differential Revision: https://reviews.freebsd.org/D5614
When locking a mutex and deadlock is detected the first mutex lock
call that sees the deadlock will return -EDEADLK .
MFC after: 1 week
Sponsored by: Mellanox Technologies
spigen provides userland API to SPI bus. Make it available as a loadable
module so people using official ARM images can enabled it on devices like
BBB or RPi without re-building kernel
MFC after: 1 week
Put large functions into linux_slab.c instead of declaring them static
inline.
Add support for more memory allocation wrappers like kmalloc_array()
and __vmalloc().
Make sure either the M_WAITOK or the M_NOWAIT flag is set and mask
away unused memory allocation flags before calling FreeBSD's malloc()
routine.
Move kmalloc_node() definition to slab.h where it belongs.
Implement support for the SLAB_DESTROY_BY_RCU feature when creating a
kmem_cache which basically means kmem_cache memory is freed using
call_rcu().
MFC after: 1 week
Sponsored by: Mellanox Technologies
The module uses unnamed structure and union fields and base GCC in
stable/10 doesn't like it.
I think that that is a C11 feature, so it is courteous of more modern
compilers to not complain about it when compiling in C99 mode.
Approved by: davidcs
MFC after: 5 days
This change makes the workqueue implementation behave more like in
Linux, both functionality wise and structure wise.
All workqueue code has been moved to linux_work.c
Add an atomic based statemachine to the work_struct to ensure proper
operation. Prior to this change struct_work was directly mapped to a
FreeBSD task. When a taskqueue has multiple threads the same task may
end up being executed on more than one worker thread simultaneously.
This might cause problems with code coming from Linux, which expects
serial behaviour, similar to Linux tasklets.
Move all global workqueue function names into the linux_xxx domain to
avoid symbol name clashes in the future.
Implement a few more workqueue related functions and macros.
Create two multithreaded taskqueues for the LinuxKPI during module
load, one for time-consuming callbacks and one for non-time consuming
callbacks.
MFC after: 1 week
Sponsored by: Mellanox Technologies
This interface has no in-tree consumers and has been more or less
non-functional for several releases.
Remove manpage note that the procfs special file 'mem' is grouped to
kmem. This hasn't been true since r81107.
Remove procfs' README file. It is an out of date duplication of the manpage
(quoth the README: "since the bsd kernel is single-processor...").
Reviewed by: vangyzen, bcr (manpage)
Approved by: des (procfs maintainer), vangyzen (mentor)
Differential Revision: https://reviews.freebsd.org/D9802
I imagine that the module would be useful only to a very limited number
of developers, so that's my excuse for not writing any documentation.
On a more serious note, please see DRAM Error Injection section of BKDGs
for families 10h - 16h. E.g. section 2.13.3.1 of BKDG for AMD Family 15h
Models 00h-0Fh Processors.
Many thanks to kib for his suggestions and comments.
Discussed with: kib
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D9824
Add opt_platform.h and opt_acpi.h to the dependencies so modules can be
built as a part of buildworld when MODULES_WITH_WORLD is set
Reported by: Andre Albsmeier (for 11-stable)
MFC after: 1 day
* Uses the IWM_FW_PAGING_BLOCK_CMD firmware command to tell the firmware
what memory ranges to use for paging.
Obtained from: dragonflybsd.git 8a5b199964f8e7bdb00039f0b48817a01b402f18
Add if_iwm_7000.c/if_iwm_8000.c to SRCS to match similar additions made
to sys/conf/files after refactoring done in the commit noted.
PR: 217308
Pointyhat to: adrian
Submitted by: Andreas Nilsson <andrnils@gmail.com>
Reported by: Jakob Alvermark <jakob@alvermark.net>, Juan Ramómon Molina Menor <listjm@club.fr>
Sponsored by: Dell EMC Isilon
When allocating unmapped pages, take advantage of the direct map on
AMD64 to get the virtual address corresponding to a page. Else all
pages allocated must be mapped because sometimes the virtual address
of a page is requested.
Move all page allocation and deallocation code into an own C-file.
Add support for GFP_DMA32, GFP_KERNEL, GFP_ATOMIC and __GFP_ZERO
allocation flags.
Make a clear separation between mapped and unmapped allocations.
Obtained from: kmacy @
MFC after: 1 week
Sponsored by: Mellanox Technologies
with geom_flashmap(4) and teach it about MMC for slicing enhanced
user data area partitions. The FDT slicer still is the default for
CFI, NAND and SPI flash on FDT-enabled platforms.
- In addition to a device_t, also pass the name of the GEOM provider
in question to the slicers as a single device may provide more than
provider.
- Build a geom_flashmap.ko.
- Use MODULE_VERSION() so other modules can depend on geom_flashmap(4).
- Remove redundant/superfluous GEOM routines that either do nothing
or provide/just call default GEOM (slice) functionality.
- Trim/adjust includes
Submitted by: jhibbits (RouterBoard bits)
Reviewed by: jhibbits
The build process generates *assym.h using nm from *genassym.o (which is
in turn created from *genassym.c).
When compiling with link-time optimization (LTO) using -flto, .o files
are LLVM bitcode, not ELF objects. This is not usable by genassym.sh,
so remove -flto from those ${CC} invocations.
Submitted by: George Rimar
Reviewed by: dim
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D9659
