entries from the interface rather than using ifconfig's delete command.
This preserves non-dhclient configured addresses (though they are wiped
out when dhclient is restarted).
MFC after: 1 week
disk. Apparently some people want to use mdmfs as mount_* as a
shortcut for mounting existing file-based file systems.
Note that unlike in the patches from the submitters, this option is
not available in compat mode. Compat mode was supposed to support only
things that mount_mfs used to support. To use this option from fstab,
mdmfs should be called mount_md, not mount_mfs. This distinction has
not always upkept for new options, and those can't be fixed now
without breaking people's systems, but new options should not usually
be allowed in compat mode. (Not sure why -F is allowed there at all.)
PR: 57641
Submitted by: Ruben de Groot
Submitted independently by: Wojciech A. Koszek, for Urzad Miasta Czestochowa
autonumbering is requested, set the unit to 0 instead of -1. This
option is just for output, and "/dev/md-1" looks disconcerting.
Submitted by: Wojciech A. Koszek
kernel is in the order the devices were made, which is not useful to
the user. Also, remove the "%d more" test since the kernel does not
return the complete count in md_pad[0] (maybe it should?).
Submitted by: Wojciech A. Koszek
action argument with the value obtained from table lookup. The feature
is now applicable only to "pipe", "queue", "divert", "tee", "netgraph"
and "ngtee" rules.
An example usage:
ipfw pipe 1000 config bw 1000Kbyte/s
ipfw pipe 4000 config bw 4000Kbyte/s
ipfw table 1 add x.x.x.x 1000
ipfw table 1 add x.x.x.y 4000
ipfw pipe tablearg ip from table(1) to any
In the example above the rule will throw different packets to different pipes.
TODO:
- Support "skipto" action, but without searching all rules.
- Improve parser, so that it warns about bad rules. These are:
- "tablearg" argument to action, but no "table" in the rule. All
traffic will be blocked.
- "tablearg" argument to action, but "table" searches for entry with
a specific value. All traffic will be blocked.
- "tablearg" argument to action, and two "table" looks - for src and
for dst. The last lookup will match.
- number of read I/O requests,
- number of write I/O requests,
- number of read bytes,
- number of written bytes.
Add 'reset' subcommand for resetting statistics.
value (intmax_t) and boolean (int).
Based on that provide three functions:
- gctl_get_ascii()
- gctl_get_int()
- gctl_get_intmax()
- Hide gctl_get_param() function, as it is only used internally in
subr.c.
- Allow to provide argument name as (fmt, ...).
- Assert geom(8) bugs (missing argument is a geom(8) bug).
- Clean-up and simplify the code by using new functions and assumtions
(no more checking for missing argument).
Tested by: regression tests
IPv6 support was committed:
- Stop treating `ip' and `ipv6' as special in `proto' option as they
conflict with /etc/protocols.
- Disuse `ipv4' in `proto' option as it is corresponding to `ipv6'.
- When protocol is specified as numeric, treat it as it is even it is
41 (ipv6).
- Allow zero for protocol as it is valid number of `ip'.
Still, we cannot specify an IPv6 over an IPv4 tunnel like before such
as:
pass ipv6 from any to any
But, now, you can specify it like:
pass ip4 from any to any proto ipv6
PR: kern/89472
Reported by: Ga l Roualland <gael.roualland__at__dial.oleane.com>
MFC after: 1 week
iov address internally through realloc(3). However, since the function
parameter wasn't designed to allow the modified iov being passed back to
the caller, we ended up feeding iov with several corrupted entries(this
depends on how many arguments were pushed into iovec before set_charset())
to nmount(2).
This commit fixes this regression introduced in rev1.37 such that
mount_msdosfs(8) with code page conversion option(-W,-D) enabled works again.
Reviewed by: rodrigc
