queue length. The default value for this parameter is 50, which is
quite low for many of today's uses and the only way to modify this
parameter right now is to edit if_var.h file. Also add read-only
sysctl with the same name, so that it's possible to retrieve the
current value.
MFC after: 1 month
This framework allows drivers to abstract the rate control algorithm and
just feed the framework with the usable parameters. The rate control
framework will now deal with passing the parameters to the selected
algorithm. Right now we have AMRR (the default) and RSSADAPT but there's
no way to select one with ifconfig, yet.
The objective is to have more rate control algorithms in the net80211
stack so all drivers[0] can use it. Ideally, we'll have the well-known
sample rate control algorithm in the net80211 at some point so all
drivers can use it (not just ath).
[0] all drivers that do rate control in software, that is.
Reviewed by: bschmidt, thompsa, weyongo
MFC after: 1 months
o replace DLT_IEEE802_11 support in net80211 with DLT_IEEE802_11_RADIO
and remove explicit bpf support from wireless drivers; drivers now
use ieee80211_radiotap_attach to setup shared data structures that
hold the radiotap header for each packet tx/rx
o remove rx timestamp from the rx path; it was used only by the tdma support
for debugging and was mostly useless due to it being 32-bits and mostly
unavailable
o track DLT_IEEE80211_RADIO bpf attachments and maintain per-vap and
per-com state when there are active taps
o track the number of monitor mode vaps
o use bpf tap and monitor mode vap state to decide when to collect radiotap
state and dispatch frames; drivers no longer explicitly directly check
bpf state or use bpf calls to tap frames
o handle radiotap state updates on channel change in net80211; drivers
should not do this (unless they bypass net80211 which is almost always
a mistake)
o update various drivers to be more consistent/correct in handling radiotap
o update ral to include TSF in radiotap'd frames
o add promisc mode callback to wi
Reviewed by: cbzimmer, rpaulo, thompsa
sleepable context for net80211 driver callbacks. This removes the need for USB
and firmware based drivers to roll their own code to defer the chip programming
for state changes, scan requests, channel changes and mcast/promisc updates.
When a driver callback completes the hardware state is now guaranteed to have
been updated and is in sync with net80211 layer.
This nukes around 1300 lines of code from the wireless device drivers making
them more readable and less race prone.
The net80211 layer has been updated as follows
- all state/channel changes are serialised on the taskqueue.
- ieee80211_new_state() always queues and can now be called from any context
- scanning runs from a single taskq function and executes to completion. driver
callbacks are synchronous so the channel, phy mode and rx filters are
guaranteed to be set in hardware before probe request frames are
transmitted.
Help and contributions from Sam Leffler.
Reviewed by: sam
- make usb2_power_mask_t 16-bit
- remove "usb2_config_sub" structure from "usb2_config". To compensate for this
"usb2_config" has a new field called "usb_mode" which select for which mode
the current xfer entry is active. Options are: a) Device mode only b) Host
mode only (default-by-zero) c) Both modes. This change was scripted using
the following sed script: "s/\.mh\././g".
- the standard packet size table in "usb_transfer.c" is now a function, hence
the code for the function uses less memory than the table itself.
Submitted by: Hans Petter Selasky
o call ieee80211_encap in ieee80211_start so frames passed down to drivers
are already encapsulated
o remove ieee80211_encap calls in drivers
o fixup wi so it recreates the 802.3 head it requires from the 802.11
header contents
o move fast-frame aggregation from ath to net80211 (conditional on
IEEE80211_SUPPORT_SUPERG):
- aggregation is now done in ieee80211_start; it is enabled when the
packets/sec exceeds ieee80211_ffppsmin (net.wlan.ffppsmin) and frames
are held on a staging queue according to ieee80211_ffagemax
(net.wlan.ffagemax) to wait for a frame to combine with
- drivers must call back to age/flush the staging queue (ath does this
on tx done, at swba, and on rx according to the state of the tx queues
and/or the contents of the staging queue)
- remove fast-frame-related data structures from ath
- add ieee80211_ff_node_init and ieee80211_ff_node_cleanup to handle
per-node fast-frames state (we reuse 11n tx ampdu state)
o change ieee80211_encap calling convention to include an explicit vap
so frames coming through a WDS vap are recognized w/o setting M_WDS
With these changes any device able to tx/rx 3Kbyte+ frames can use fast-frames.
Reviewed by: thompsa, rpaulo, avatar, imp, sephe
o remove ic_myaddr from ieee80211com
o change ieee80211_ifattach to take the mac address of the physical device
and use that to setup the lladdr.
o replace all references to ic_myaddr in drivers by IF_LLADDR
o related cleanups (e.g. kill dead code)
PR: kern/133178
Reviewed by: thompsa, rpaulo
