When a network device is departing, the RoCE GID entries should be
cleared before the default L2 link layer address is freed. Else a NULL
pointer access may happen.
MFC after: 1 week
Sponsored by: Mellanox Technologies
VLANs in ibcore.
IPv6 link local addresses are usually derived from the netdev MAC
address. This is applicable to VLAN devices and its lower netdevice as
well. In such cases the IPv6 link local address is a duplicate of the
default GID.
Now that link local IPv6 addresses based GIDs are supported, allow
adding such GID entries in the GID table.
MFC after: 1 week
Sponsored by: Mellanox Technologies
only use the first driver, however this may change in the future and
hardware exists with multiple ITS devices.
Sponsored by: DARPA, AFRL
Sponsored by: Cavium (Hardware)
Pretty much any other device might need to manipulate a gpio pin during its
probe or attach routines, so these devices must be available as early as
possible.
The gpio device is an interrupt controller, but I didn't choose the
INTERRUPT pass for that reason (it works fine as an interrupt controller as
long as it attaches any time before interrupts are enabled). That just
looked like the right place in the passes to ensure that it attaches before
any type of device that might need gpio pin manipulations.
Rename ACPI_IVRS_HARDWARE_NEW to ACPI_IVRS_HARDWARE_EFRSUP, since new definitions add Extended Feature Register support. Use IvrsType to distinguish three types of IVHD - 0x10(legacy), 0x11 and 0x40(with EFR). IVHD 0x40 is also called mixed type since it supports HID device entries.
Fix 2 coverity bugs reported by cem.
Reported by:jkim, cem
Approved by:grehan
Differential Revision://reviews.freebsd.org/D14501
driver requires interrupts to do transfers, and the drivers for the SPI
devices on the bus quite reasonably expect to be able to do IO while probing
and attaching.
Normally after grabbing the lock it has to be verified we got the right one
to begin with. However, if we are recursing, it must not change thus the
check can be avoided. In particular this avoids a lock read for non-recursing
case which found out the lock was changed.
While here avoid an irq trip of this happens.
Tested by: pho (previous version)
of years since the century, so strip the century out when converting to or
from bcd_clocktime format (the conversion routines will infer century by
pivoting on 70).
The code already pays the cost of reading the lock to obtain the waiters
flag. Checking whether there is more than one reader is not a problem and
avoids dirtying the line.
This also fixes a small corner case: if waiters were to show up between
reading the flag and upgrading the lock, the operation would fail even
though it should not. No correctness change here though.
If there were exactly rowner_retries/asx_retries (by default: 10) transitions
between read and write state and the waiters still did not get the lock, the
next owner -> reader transition would result in the code correctly falling
back to turnstile/sleepq where it would incorrectly think it was waiting
for a writer and decide to leave turnstile/sleepq to loop back. From this
point it would take ts/sq trips until the lock gets released.
The bug sometimes manifested itself in stalls during -j 128 package builds.
Refactor the code to fix the bug, while here remove some of the gratituous
differences between rw and sx locks.
POSIX defines no macros for these permissions.
Also remove unneeded headers from synopsis.
PR: 225905
Reviewed by: wblock
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D14461
The main routine takes 8 args, 3 of which are almost the same for most uses.
This in particular pushes it above the limit of 6 arguments passable through
registers on amd64 making it impossible to tail call.
This is a prerequisite for further cleanups.
Tested by: pho
