offset within the buffer to align the L3 headers we know the buffer itself
was allocated and sized on cacheline boundaries and we don't need to
preserve partitial cachelines at the start and end of the buffer when
doing busdma sync operations.
to copying in some code from the armv4 busdma, and adapting a few variable
and flag names to match the surrounding mips code.
Instead of keeping a local cache of prealloced busdma_map structs on a
mutex-protected list, set up an uma zone to cache them.
Instead of all memory allocations using M_DEVBUF, use new categories
M_BUSDMA for allocations of metadata (tags, maps, segment tracking lists),
and M_BOUNCE for bounce pages.
When buffers are allocated out of the busdma_bufalloc zones the alignment
and size of the buffers is known, and the code can skip doing any "partial
cacheline flush" logic to preserve data that may be adjacent to the DMA
buffer but contain non-DMA data.
Reviewed by: adrian, imp
and implement support for VM_MEMATTR_UNCACHEABLE. This will be used in
upcoming changes to support BUS_DMA_COHERENT in bus_dmamem_alloc().
Reviewed by: adrian, imp
This was triggering when using it as an AP bridge rather than an ethernet
bridge.
The code is unclear but it works; I'll fix it to be clearer and test
performance at a later stage.
The existing code meets the "alignment" requirement for the l3 payload
by offsetting the mbuf by uint64_t and then calling an rx fixup routine
to copy the frame backwards by 2 bytes. This DWORD aligns the
L3 payload so tcp, etc doesn't panic on unaligned access.
This is .. slow.
For arge MACs that support 1 byte TX/RX address alignment, we can do
the "other" hack: offset the RX address of the mbuf so the L3 payload
again is hopefully DWORD aligned.
This is much cheaper - since TX/RX is both 1 byte align ready (thanks
to the previous commit) there's no bounce buffering going on and there
is no rx fixup copying.
This gets bridging performance up from 180mbit/sec -> 410mbit/sec.
There's around 10% of CPU cycles spent in _bus_dmamap_sync(); I'll
investigate that later.
Tested:
* QCA955x SoC (AP135 reference board), bridging arge0/arge1
by programming the switch to have two vlangroups in dot1q mode:
# ifconfig bridge0 inet 192.168.2.20/24
# etherswitchcfg config vlan_mode dot1q
# etherswitchcfg vlangroup0 members 0,1,2,3,4
# etherswitchcfg vlangroup1 vlan 2 members 5,6
# etherswitchcfg port5 pvid 2
# etherswitchcfg port6 pvid 2
# ifconfig arge1 up
# ifconfig bridge0 addm arge1
The early ethernet MACs (I think AR71xx and AR913x) require that both
TX and RX require 4-byte alignment for all packets.
The later MACs have started relaxing the requirements.
For now, the 1-byte TX and 1-byte RX alignment requirements are only for
the QCA955x SoCs. I'll add in the relaxed requirements as I review the
datasheets and do testing.
* Add a hardware flags field and 1-byte / 4-byte TX/RX alignment.
* .. defaulting to 4-byte TX and 4-byte RX alignment.
* Only enforce the TX alignment fixup if the hardware requires a 4-byte
TX alignment. This avoids a call to m_defrag().
* Add counters for various situations for further debugging.
* Set the 1-byte and 4-byte busdma alignment requirement when
the tag is created.
This improves the straight bridging performance from 130mbit/sec
to 180mbit/sec, purely by removing the need for TX path bounce buffers.
The main performance issue is the RX alignment requirement and any RX
bounce buffering that's occuring. (In a local test, removing the RX
fixup path and just aligning buffers raises the performance to above
400mbit/sec.
In theory it's a no-op for SoCs before the QCA955x.
Tested:
* QCA9558 SoC in AP135 board, using software bridging between arge0/arge1.
The ERL is a fairly cheap (~$100 USD) and readily available dual core
MIPS64 device so it makes a useful MIPS reference platform.
This is based in part on the kernel config generated by the mkerlimage
script from http://rtfm.net/FreeBSD/ERL/.
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3884
* Shuffle the kernel to be at the beginning
* Give the kernel 2mb, the rootfs 6mb, and 'mib0' the rest
* put the cfg parition just before the ART calibration data for the
wifi part in the SoC
* .. and make sure ART points to the right 64k region.
I've updated the freebsd-wifi-build wiki the instructions on using this.
If someone has an AP135 with 8MB SPI flash then this won't work; everything
minus the big mib0 partition is just a bit over 8MB. Come see me if this
ever happens (you'll likely just have to shrink the rootfs and the kernel
a little in order to make it fit.)
Tested:
* AP135 reference board.
belong to a vm object, they can't be paged out. Since they can't be paged
out, they are never enqueued in a paging queue. Nonetheless, passing
PQ_INACTIVE to vm_page_unwire() creates the appearance that these pages
are being enqueued in the inactive queue. As of r288122, we can avoid
this false impression by passing PQ_NONE.
Submitted by: kmacy (an earlier version)
Differential Revision: https://reviews.freebsd.org/D1674
linkers no longer raise an error when undefined weak symbols are
found, but relocate as if the symbol value was 0. Note that we do not
repeat the mistake of userspace dynamic linker of making the symbol
lookup prefer non-weak symbol definition over the weak one, if both
are available. In fact, kernel linker uses the first definition
found, and ignores duplicates.
Signature of the elf_lookup() and elf_obj_lookup() functions changed
to split result/error code and the symbol address returned.
Otherwise, it is impossible to return zero address as the symbol
value, to MD relocation code. This explains the mechanical changes in
elf_machdep.c sources.
The powerpc64 R_PPC_JMP_SLOT handler did not checked error from the
lookup() call, the patch leaves the code as is (untested).
Reported by: glebius
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
When the system has more than a single PCI domain, the bus numbers
are not unique, thus they cannot be used for "pci" device numbering.
Change bus numbers to -1 (i.e. to-be-determined automatically)
wherever the code did not care about domains.
Reviewed by: jhb
Obtained from: Semihalf
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3406
running thread.
It is currently implemented only on amd64 and i386; on these
architectures, it is implemented by raising an NMI on the CPU on which
the target thread is currently running. Unlike stack_save_td(), it may
fail, for example if the thread is running in user mode.
This change also modifies the kern.proc.kstack sysctl to use this function,
so that stacks of running threads are shown in the output of "procstat -kk".
This is handy for debugging threads that are stuck in a busy loop.
Reviewed by: bdrewery, jhb, kib
Sponsored by: EMC / Isilon Storage Division
Differential Revision: https://reviews.freebsd.org/D3256
The only operation which is prevented by the hold is the kernel stack
swapout for the faulted thread, which should be fine to allow.
Remove useless checks for NULL curproc or curproc->p_vmspace from the
trap_pfault() wrappers on x86 and powerpc.
Reviewed by: alc (previous version)
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
nlge(4) is supposed to deprecate rge(4) for Broadcom XLR when it was
introduced 5 years ago.
rge doesn't build on -CURRENT due to MII changes. All the XLR kernel confs
use nlge. Let's get rid of the old driver for FreeBSD 11. We can use
10-STABLE or SVN to go back and look at the old driver if needed.
Differential Revision: https://reviews.freebsd.org/D3339
Submitted by: kevin.bowling@kev009.com
Add a check to preload_search_info to make sure mod is set. Most of the
callers of preload_search_info don't check that the mod parameter is
set, which can cause page faults. While at it, remove some now unnecessary
checks before calling preload_search_info.
Sponsored by: Citrix Systems R&D
Reviewed by: kib
Differential Revision: https://reviews.freebsd.org/D3440
vm_offset_t pmap_quick_enter_page(vm_page_t m)
void pmap_quick_remove_page(vm_offset_t kva)
These will create and destroy a temporary, CPU-local KVA mapping of a specified page.
Guarantees:
--Will not sleep and will not fail.
--Safe to call under a non-sleepable lock or from an ithread
Restrictions:
--Not guaranteed to be safe to call from an interrupt filter or under a spin mutex on all platforms
--Current implementation does not guarantee more than one page of mapping space across all platforms. MI code should not make nested calls to pmap_quick_enter_page.
--MI code should not perform locking while holding onto a mapping created by pmap_quick_enter_page
The idea is to use this in busdma, for bounce buffer copies as well as virtually-indexed cache maintenance on mips and arm.
NOTE: the non-i386, non-amd64 implementations of these functions still need review and testing.
Reviewed by: kib
Approved by: kib (mentor)
Differential Revision: http://reviews.freebsd.org/D3013
provide a semantic defined by the C11 fences with corresponding
memory_order.
atomic_thread_fence_acq() gives r | r, w, where r and w are read and
write accesses, and | denotes the fence itself.
atomic_thread_fence_rel() is r, w | w.
atomic_thread_fence_acq_rel() is the combination of the acquire and
release in single operation. Note that reads after the acq+rel fence
could be made visible before writes preceeding the fence.
atomic_thread_fence_seq_cst() orders all accesses before/after the
fence, and the fence itself is globally ordered against other
sequentially consistent atomic operations.
Reviewed by: alc
Discussed with: bde
Sponsored by: The FreeBSD Foundation
MFC after: 3 weeks
and start teaching subsystems about it.
The Atheros MIPS platforms don't guarantee any kind of FIFO consistency
with interrupts in hardware. So software needs to do a flush when it
receives an interrupt and before it calls the interrupt handler.
There are new ones for the QCA934x and QCA955x, so do a few things:
* Get rid of the individual ones (for ethernet and IP2);
* Create a mux and enum listing all the variations on DDR flushes;
* replace the uses of IP2 with the relevant one (which will typically
be "PCI" here);
* call the USB DDR flush before calling the real USB interrupt handlers;
* call the ethernet one upon receiving an interrupt that's for us,
rather than never calling it during operation.
Tested:
* QCA9558 (TP-Link archer c7 v2)
* AR9331 (Carambola 2)
TODO:
* PCI, USB, ethernet, etc need to do a double-check to see if the
interrupt was truely for them before doing the DDR. For now I
prefer "correct" over "fast".
The SoC, the flash, the ethernet ports and ethernet switch all work.
The USB works.
The 11ac PCIe NIC internally is at least seen by the PCIE RC, but
I haven't tried using it yet. There's no driver and I haven't
yet swapped it out for a non-11ac chip.
The on-chip 2GHz wifi works, but there are some data errors that
get thrown up in STA mode when scanning. I have a feeling I have
to finish the DDR flush code out and have it run correctly on the
shared interrupts; that'll take a bit of time to get right.
But if you're after an updated piece of hardware, the Archer C7 v2
is certainly there, and you can replace the 11ac NIC with a 3x3
Atheros PCIe device (eg AR9380, AR9390, AR9580, etc) and it'll
"just work".
Tested:
* TP-Link archer c7v2.
The Tp-link Archer-C7v2 unit has a QCA9558 internally but hangs the
QCA988x 11ac PCIe NIC off of PCI RC #1, not #0.
So I actually finally /do/ have a board to verify whether PCIe is working.
Grr.
Tested:
* TP-Link Archer-C7v2.
* GENERAL
- Update copyright.
- Make kernel options for RANDOM_YARROW and RANDOM_DUMMY. Set
neither to ON, which means we want Fortuna
- If there is no 'device random' in the kernel, there will be NO
random(4) device in the kernel, and the KERN_ARND sysctl will
return nothing. With RANDOM_DUMMY there will be a random(4) that
always blocks.
- Repair kern.arandom (KERN_ARND sysctl). The old version went
through arc4random(9) and was a bit weird.
- Adjust arc4random stirring a bit - the existing code looks a little
suspect.
- Fix the nasty pre- and post-read overloading by providing explictit
functions to do these tasks.
- Redo read_random(9) so as to duplicate random(4)'s read internals.
This makes it a first-class citizen rather than a hack.
- Move stuff out of locked regions when it does not need to be
there.
- Trim RANDOM_DEBUG printfs. Some are excess to requirement, some
behind boot verbose.
- Use SYSINIT to sequence the startup.
- Fix init/deinit sysctl stuff.
- Make relevant sysctls also tunables.
- Add different harvesting "styles" to allow for different requirements
(direct, queue, fast).
- Add harvesting of FFS atime events. This needs to be checked for
weighing down the FS code.
- Add harvesting of slab allocator events. This needs to be checked for
weighing down the allocator code.
- Fix the random(9) manpage.
- Loadable modules are not present for now. These will be re-engineered
when the dust settles.
- Use macros for locks.
- Fix comments.
* src/share/man/...
- Update the man pages.
* src/etc/...
- The startup/shutdown work is done in D2924.
* src/UPDATING
- Add UPDATING announcement.
* src/sys/dev/random/build.sh
- Add copyright.
- Add libz for unit tests.
* src/sys/dev/random/dummy.c
- Remove; no longer needed. Functionality incorporated into randomdev.*.
* live_entropy_sources.c live_entropy_sources.h
- Remove; content moved.
- move content to randomdev.[ch] and optimise.
* src/sys/dev/random/random_adaptors.c src/sys/dev/random/random_adaptors.h
- Remove; plugability is no longer used. Compile-time algorithm
selection is the way to go.
* src/sys/dev/random/random_harvestq.c src/sys/dev/random/random_harvestq.h
- Add early (re)boot-time randomness caching.
* src/sys/dev/random/randomdev_soft.c src/sys/dev/random/randomdev_soft.h
- Remove; no longer needed.
* src/sys/dev/random/uint128.h
- Provide a fake uint128_t; if a real one ever arrived, we can use
that instead. All that is needed here is N=0, N++, N==0, and some
localised trickery is used to manufacture a 128-bit 0ULLL.
* src/sys/dev/random/unit_test.c src/sys/dev/random/unit_test.h
- Improve unit tests; previously the testing human needed clairvoyance;
now the test will do a basic check of compressibility. Clairvoyant
talent is still a good idea.
- This is still a long way off a proper unit test.
* src/sys/dev/random/fortuna.c src/sys/dev/random/fortuna.h
- Improve messy union to just uint128_t.
- Remove unneeded 'static struct fortuna_start_cache'.
- Tighten up up arithmetic.
- Provide a method to allow eternal junk to be introduced; harden
it against blatant by compress/hashing.
- Assert that locks are held correctly.
- Fix the nasty pre- and post-read overloading by providing explictit
functions to do these tasks.
- Turn into self-sufficient module (no longer requires randomdev_soft.[ch])
* src/sys/dev/random/yarrow.c src/sys/dev/random/yarrow.h
- Improve messy union to just uint128_t.
- Remove unneeded 'staic struct start_cache'.
- Tighten up up arithmetic.
- Provide a method to allow eternal junk to be introduced; harden
it against blatant by compress/hashing.
- Assert that locks are held correctly.
- Fix the nasty pre- and post-read overloading by providing explictit
functions to do these tasks.
- Turn into self-sufficient module (no longer requires randomdev_soft.[ch])
- Fix some magic numbers elsewhere used as FAST and SLOW.
Differential Revision: https://reviews.freebsd.org/D2025
Reviewed by: vsevolod,delphij,rwatson,trasz,jmg
Approved by: so (delphij)
This makes the TP-Link WDR3600 routers more useful
Differential Revision: https://reviews.freebsd.org/D2780
Approved by: adrian
Sponsored by: ScaleEngine Inc.
Native ABI do not need signal conversion, only emulators may want this. Usually
emulators implements its own sv_sendsig method. For now only ibcs2 emulator does
not have own sv_sendsig implementation and depends on native sendsig() method.
So, remove any extra attempts to convert signal numbers from native sendsig()
methods except from i386 where ibsc2 is living.
when allocation fails, it suffices to perform VM_WAIT. The direct map
covers the entirely of physical memory, so unlike 32-bit mips any
physical page can be used as a page table page.
years for head. However, it is continuously misused as the mpsafe argument
for callout_init(9). Deprecate the flag and clean up callout_init() calls
to make them more consistent.
Differential Revision: https://reviews.freebsd.org/D2613
Reviewed by: jhb
MFC after: 2 weeks
The replacement started at r283088 was necessarily incomplete without
replacing boolean_t with bool. This also involved cleaning some type
mismatches and ansifying old C function declarations.
Pointed out by: bde
Discussed with: bde, ian, jhb
* Change mips24k -> mips74k for hwpmc, but leave it disabled for now.
* don't build pci by default.
* build pci and qca955x_pci for AP135, as theres a PCIe NIC.
* don't build a hwpmc module, it doesn't really work out well
for the mips boards at the moment.
* add ipfw and DEFAULT_TO_ACCEPT.
The QCA955x looks a lot like the AR724x PCIe controller, except it
supports two root complexes. Unfortunately I only have one, so
although this code has started down the path of supporting more than
one, it's definitely not yet ready.
Tested:
* AP135 board (QCA9558 SoC), with the 11ac NIC swapped for an AR9380
PCIe NIC.
Notes:
* Yes, this driver isn't very pretty. I decided to commit what I have
versus holding onto something that isn't yet finished. It is enough
to bring up the above NIC and interrupt routing works, so it's a good
start.
* However, yes, the DDR flush routine hooks need to be fixed up.
I don't think I'm firing the right one at the moment.
pages which pass a NULL virtual address. If the BUS_DMA_KEEP_PG_OFFSET
flag is set, use the physical address to compute the page offset
instead. The physical address should always be valid when adding
bounce pages and should contain the same page offset like the virtual
address.
Submitted by: Svatopluk Kraus <onwahe@gmail.com>
MFC after: 1 week
Reviewed by: jhb@
The carambola2 exposes all the gpio pins, but some are reserved for
core functions (eg usb, ethernet, etc.) Others are configured by default
to be available as normal GPIO pins to do interesting things with.
GPIO 18->23 is the I2S, SLIC and SPDIF device pins, but none of those
are currently used. So, just allow those to show up.
Tested:
* AR9344, Carambola 2
* (.. bitbang SPI to an Adafruit LCD via libgpio, because FreeBSD could
do with more shiny output devices that aren't network interfaces.)
TODO:
There are some other pins aren't currently included here, but should be.
The LED pins are for the internal switch inside the AR9344.
* GPIO 0+1 are "LED0 + LED1", but they're tied to high for bootstrapping.
* GPIO 13-17 are "LED2..7", but they're tied (H, L, L, L, H) for bootstrapping.
* GPIO 11 and 12 are UART RTS/CTS or I2S; but GPIO 12 is tied L for bootstrap.
This is needed with the pl011 driver. Before this change it would default
to a shift of 0, however the hardware places the registers at 4-byte
addresses meaning the value should be 2.
This patch fixes this for the pl011 when configured using the fdt. The
other drivers have a default value of 0 to keep this a no-op.
MFC after: 1 week
and export them to userland.
- Define __HAVE_REG32 on platforms that define a reg32 structure and check
for this in <sys/procfs.h> to control when to export prstatus32, etc.
- Add prstatus32_t and prpsinfo32_t typedefs for the 32-bit structures.
libbfd looks for these types, and having them fixes 'gcore' in gdb of a
32-bit process on a 64-bit platform.
- Use the structure definitions from <sys/procfs.h> in gcore's elf32 core
dump code instead of duplicating the definitions.
Differential Revision: https://reviews.freebsd.org/D2142
Reviewed by: kib, nathanw (powerpc bits)
MFC after: 1 week
The MAC addresses were totally wrong. They're like the DIR-625C1 - at
0x1ffe0004 and 0x1ffe0018. They're however stored as text strings.
The ath0 MAC address is also not set, even though the calibration
partition is valid.
So, pick the board address / first MAC as the ath0 MAC, and derive
arge0/arge1 from that. That way they're hopefully unique enough
for people with multiple devices.
Tested:
* DIR-655A1
TODO:
* Do the same for the DIR-625A1 and DIR-625C1.
A couple of internal functions used by malloc(9) and uma truncated
a size_t down to an int. This could cause any number of issues
(e.g. indefinite sleeps, memory corruption) if any kernel
subsystem tried to allocate 2GB or more through malloc. zfs would
attempt such an allocation when run on a system with 2TB or more
of RAM.
Note to self: When this is MFCed, sparc64 needs the same fix.
Differential revision: https://reviews.freebsd.org/D2106
Reviewed by: kib
Reported by: Michael Fuckner <michael@fuckner.net>
Tested by: Michael Fuckner <michael@fuckner.net>
MFC after: 2 weeks
This allows the TL-WDR3600 to use the correct MAC address for ath0, ath1
and arge0. arge1 isn't used; until I disable it entirely it'll just
show up with a randomly generated MAC.
A lot of these dinky atheros based MIPS boards don't have a nice, well,
anything consistent defining their MAC addresses for things.
The Atheros reference design boards will happily put MAC addresses
into the wifi module calibration data like they should, and individual
ethernet MAC addresses into the calibration area in flash.
That makes my life easy - "hint.arge.X.eeprommac=<addr>" reads from
that flash address to extract a MAC, and everything works fine.
However, aside from some very well behaved vendors (eg the Carambola 2
board), everyone else does something odd.
eg:
* a MAC address in the environment (eg ubiquiti routerstation/RSPRO)
that you derive arge0/arge1 MAC addresses from.
* a MAC address in flash that you derive arge0/arge1 MAC addresses from.
* The wifi devices having their own MAC addresses in calibration data,
like normal.
* The wifi devices having a fixed, default or garbage value for a MAC
address in calibration data, and it has to be derived from the
system MAC.
So to support this complete nonsense of a situation, there needs to be
a few hacks:
* The "board" MAC address needs to be derived from somewhere and squirreled
away. For now it's either redboot or a MAC address stored in calibration
flash.
* Then, a "map" set of hints to populate kenv with some MAC addresses
that are derived/local, based on the board address. Each board has
a totally different idea of what you do to derive things, so each
map entry has an "offset" (+ve or -ve) that's added to the board
MAC address.
* Then if_arge (and later, if_ath) should check kenv for said hint and
if it's found, use that rather than the EEPROM MAC address - which may
be totally garbage and not actually work right.
In order to do this, I've undone some of the custom redboot expecting
hacks in if_arge and the stuff that magically adds one to the MAC
address supplied by the board - instead, as I continue to test this
out on more hardware, I'll update the hints file with a map explaining
(a) where the board MAC should come from, and (b) what offsets to use
for each device.
The aim is to have all of the tplink, dlink and other random hardware
we run on have valid MAC addresses at boot, so (a) people don't get
random B:S:D❌x:x ethernet MACs, and (b) the wifi MAC is valid
so it works rather than trying to use an invalid address that
actually upsets systems (think: multicast bit set in BSSID.)
Tested:
* TP-Link TL_WDR3600 - subsequent commits will add the hints map
and the if_ath support.
TODO:
* Since this is -HEAD, and I'm all for debugging, there's a lot of
printf()s in here. They'll eventually go under bootverbose.
* I'd like to turn the macaddr routines into something available
to all drivers - too many places hand-roll random MAC addresses
and parser stuff. I'd rather it just be shared code.
However, that'll require more formal review.
* More boards.
Without this the autotuning fails for small amounts of RAM (32mb),
which all the AR91xx shipping products seemed to have.
Thanks to gjb for reminding me to re-test this stuff.
Tested:
* AR91xx, TP-Link TL-WR1043nd v1
This is based on the AP135 design - QCA9558 SoC, 3x3 2GHz wifi, but no
5GHz (11n or 11ac) chip is available.
It however still has 128MiB of RAM, 16MiB of NOR flash and the AR8327N
gigabit switch - so it's quite a beefy router device.
Tested:
* Well, a unit, naturally
Obtained from: Completely messing up an amazon.com order and getting this instead, and asking "hey, wonder if I could.."
* add ipfw
* delete ath / ath_ahb for now, until I can have Warner beat me
with the clue stick about putting in conditional build things into
the ath Makefile so the module builds can just have the HAL bits
that are relevant for a particular target.
These are actually almost the same units; except one is 3x3 5GHz, and
one is 2x2 5GHz.
Tested:
* TP-Link TL-WDR3600
TODO:
* The ath0/ath1 MAC addresses are ye garbage (00:02:03:04:05:06); fixing
that will take a little more time. It works fine with the ath0/ath1
MAC addresses set manually.
* Go through and yank the AR9344 on-board switch config (arswitch1);
it's not required here for this AP.
The AR934x (and maybe others in this family) have a more complicated
GPIO mux. The AR71xx just has a single function register for a handful
of "GPIO or X" options, however the AR934x allows for one of roughly
100 behaviours for each GPIO pin.
So, this adds a quick hints based mechanism to configure the output
functions, which is required for some of the more interesting board
configurations. Specifically, some use external LNAs to improve
RX, and without the MUX/output configured right, the 2GHz RX side
will be plain terrible.
It doesn't yet configure the "input" side yet; I'll add that if
it's required.
Tested:
* TP-Link TL-WDR3600, testing 2GHz STA/AP modes, checking some
basic RX sensitivity things (ie, "can I see the AP on the other
side of the apartment that intentionally has poor signal reception
from where I am right now.")
Whilst here, fix a silly bug in the maxpin routine; I was missing
a break.
A lot of these embedded boards don't have a unique MAC address per
device stored somewhere unique - sometimes they'll have one MAC
for both arge NICs; someties they'll have one MAC for both arge NICs
/and/ the ath NICs. In these instances, we need to derive device
specific MAC addresses from the base MAC address.
These functions will be used by some follow-up code that'll slot
into if_arge and if_ath.
Otherwise, the initial media speed would change if a PHY is hooked up,
sending PHY speed notifications. For the AP135 at least, the RGMII
PHY has a static speed/duplex configured and if the PHY plumbing
attaches the PHY to the if_arge interface, the first link speed change
from 1000/full will set the MAC to something that isn't useful.
This shouldn't affect any other platforms - everything I looked at is
using hard-coded speed/duplex as static, as they're facing a switch
with no PHY attached.
* Force the arge0 interface to not use a PHY for speed negotiation
for now. It'd be nice to do it, but right now the RGMII interface
to the switch needs to stay at 1000/full in order to match what
the switch side of the port is programmed as.
So until that's all sorted out, disconnect arge0 from the PHY
and leave it at fixed at 1000/full.
I noticed this when I tried using a busted ethernet cable that
forced the PHY to negotiate 100/full. The switch was fine and
it negotiated to 100/full, but then arge0 saw the link update
and set the speed to 100/full when the switch side of that
hook up was set to 1000/full. Tsk.
* When using argemdio, the mdio device resets and initialises
the MAC, /not/ the arge_attach (or, as I discovered, arge_init.)
So arge1 wasn't being fully initialised and thus no traffic
would ever flow.
So until I tidy up that mess, just create an argemdio bus for
arge1. It's totally fine; it won't do anything or find anything
attached to it.
Tested:
* AP135 reference board - both arge0 and arge1 now work.
This is a QCA9558 SoC (2ghz 3x3) with an atheros 11ac PCIe 5GHz 3x3
NIC and an AR8327 gigabit ethernet switch.
TODO:
* The AR8327 gigabit switch support bugfixes are forthcoming.
* 11ac support and 11ac NIC support
This is enough to bring up the basic SoC support.
What works thus far:
* The mips74k core, pll setup, and UART (or else well, stuff would
be really difficult..)
* both USB 2.0 EHCI controllers
* on-board 2GHz 3x3 wifi (the other variant has 2GHz/5GHz wifi on-chip);
* arge0 - not yet sure why arge1 isn't firing off interrupts and thus
handling traffic, but I will soon figure it out and fix it here.
Tested:
* AP135 reference design, QCA9558 SoC, pretending to be an 11n
2GHz AP.
TODO:
* There's an interrupt mux hooking up devices to IP2 and IP3 - but it's
not a read-and-clear or write-to-clear register. So, trying to use it
naively like I have been ends up with massive interrupt storms.
For now the things that share those interrupts can just take them as
shared interrupts and try to play nice.
* There's two PCIe root complexes /and/ one of them can actually be
a PCIe device endpoint. Yes, you heard right. I have to teach the
AR724x PCIe bridge code to handle multiple instances with multiple
memory/irq regions, and then there'll be RC support, but EP support
isn't on my TODO list.
* I'm not sure why arge1 isn't up and running. I'll go figure that
out soon and fix it here.
Thankyou to Qualcomm Atheros for providing me with hardware and
an abundance of documentation about these things.
There's two EHCI controllers in the QCA955x SoCs - they have different
interrupts available via various demux registers, but they both tie to
IP3.
So for now, allow them to be sharable so they can hang off of IP3.
There's a lot more to come - the QCA955x has a bunch more GPIO MUX
configuration, reminiscent of what the ARM chips let you do - but
it'll have to come later.
This will override the resource allocation of simplebus, and also
merge the resource allocation code which was in xlp_pci.c.
With this change the SoC devices that does not have proper PCI
resources will be on the FDT simplebus. We can remove
sys/mips/nlm/dev/cfi_pci_xlp.c and sys/mips/nlm/dev/uart_pci_xlp.c
Handling some interrupts in XLP (like PCIe and SATA) involves writing to
vendor specific registers as part of interrupt acknowledgement.
This was earlier done with xlp_establish_intr(), but a better solution
is to provide a function xlp_set_bus_ack() that can be used with
cpu_establish_hardintr(). This will allow platform initialization code to
setup these ACKs without changing the standrard drivers.
Gather all the IRQ definitions to interrupt.h. Earlier these were in xlp.h
and pic.h. Update the definition of XLP_IRQ_IS_PICINTR to check for last
irq as well.
const. On x86, even after the machine context is supposedly read into
the struct ucontext, lazy FPU state save code might only mark the FPU
data as hardware-owned. Later, set_fpcontext() needs to fetch the
state from hardware, modifying the *mcp.
The set_mcontext(9) is called from sigreturn(2) and setcontext(2)
implementations and old create_thread(2) interface, which throw the
*mcp out after the set_mcontext() call.
Reported by: dim
Discussed with: jhb
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
for i386, and from the code inspection, nothing in the
arm/mips/sparc64 implementations depends on it.
Discussed with: imp, nwhitehorn
Sponsored by: The FreeBSD Foundation
MFC after: 3 weeks
This avoids universe trying to build MALTA_COMMON and fail due to
the problem addressed in r276773.
Include std.MALTA from the MALTA mipsel and MALTA64 mips64el config files,
where the machine lines exist.
code in sys/kern/kern_dump.c. Most dumpsys() implementations are nearly
identical and simply redefine a number of constants and helper subroutines;
a generic implementation will make it easier to implement features around
kernel core dumps. This change does not alter any minidump code and should
have no functional impact.
PR: 193873
Differential Revision: https://reviews.freebsd.org/D904
Submitted by: Conrad Meyer <conrad.meyer@isilon.com>
Reviewed by: jhibbits (earlier version)
Sponsored by: EMC / Isilon Storage Division
socket-buffer implementations, introduce a return value for MCLGET()
(and m_cljget() that underlies it) to allow the caller to avoid testing
M_EXT itself. Update all callers to use the return value.
With this change, very few network device drivers remain aware of
M_EXT; the primary exceptions lie in mbuf-chain pretty printers for
debugging, and in a few cases, custom mbuf and cluster allocation
implementations.
NB: This is a difficult-to-test change as it touches many drivers for
which I don't have physical devices. Instead we've gone for intensive
review, but further post-commit review would definitely be appreciated
to spot errors where changes could not easily be made mechanically,
but were largely mechanical in nature.
Differential Revision: https://reviews.freebsd.org/D1440
Reviewed by: adrian, bz, gnn
Sponsored by: EMC / Isilon Storage Division
The QCA955x has more mux interrupts going on - and the AR934x actually does,
but I cheated and assigned wlan and pcie to the same interrupt line.
They are, there's just a status register mux that I should've been using.
Luckily this isn't too bad a change in itself - almost all of the
Atheros MIPS configurations use a _BASE file to inherit from.
Except PB92, which I should really fix up at some point.
The AR934x will use the legacy apb for now until I write its replacement.
The QCA955x SoC I'm doing bring-up on will have a separate qca955x_apb.c
implementation that includes hooking into IP2/IP3 and doing further
interrupt demuxing as appropriate.
APB mux.
It's larger than the AR71xx because it needs to replace the nexus
for some devices (notably wifi) and the wifi driver (if_ath_ahb.c)
reads the SPI data directly at early boot whilst it's memory mapped
in.
I'm eventually going to rip it out and replace it with a firmware
interface similar to what exists for the if_ath_pci.c path -
something early on (likely something new that I'll write) will
suck in the calibration data into a firmware API blob and that'll
be accessed from if_ath_ahb.c.
But, one thing at a time.
Tested:
* QCA955x SoC, AP135 development board
This adds the initial frequency poking and configures up enough
for it to boot and spit out data over the console.
There's still a whole bunch of work to do in the reset path
and devices to support this thing, but hey, it's alive!
ath> go 0x80050100
## Starting application at 0x80050100 ...
CPU platform: Atheros AR9558 rev 0
CPU Frequency=720 MHz
CPU DDR Frequency=600 MHz
CPU AHB Frequency=200 MHz
platform frequency: 720 MHz
CPU reference clock: 0 MHz
CPU MDIO clock: 40 MHz
Done at: hackathon
Obtained from: Linux OpenWRT, Qualcomm Atheros
There's likely a bunch of register offsets that I have to add the
register window base to before I use them.
Done at: Hackathon
Obtained from: Linux OpenWRT
The AR934x and later (which will turn up eventually) have a new GPIO
output configuration option - a real MUX rather than a "GPIO or this
function."
For now I'm squirreling it away in the CPU code just so it's done -
I may move this to the GPIO layer later.
Specifically, this is required for setting up some boards that have
external receive side LNA (low noise amplifier) that gets switched on/off
by the on-chip wireless MAC. If we don't add this support for those
boards then we'll end up with really poor performance.
(I don't yet have one of those APs, but it'll likely show up in a week.)
Obtained from: Linux OpenWRT
The elftoolchain project includes these additional defines for various
userland programs. Given that arch-specific defines are still interesting
in the context of userland programs reading or writing ELF metadata, they
should be included in top-level ELF headers.
Remove duplicate defines from ARM and MIPS elf headers.
Submitted by: will (initial version)
Reviewed by: imp, will
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D844
managing pages from different address ranges. Generally speaking, this
feature is used to increase the likelihood that physical pages are
available that can meet special DMA requirements or can be accessed through
a limited-coverage direct mapping (e.g., MIPS). However, prior to this
change, the configuration of the free lists was static, i.e., it was
determined at compile time. Consequentally, free lists could be created
for address ranges that held no actual pages, for example, on 32-bit MIPS-
based systems with 512 MB or less of physical memory. This change makes
the creation of the free lists dynamic, i.e., it is based on the available
physical memory at boot time.
On 64-bit x86-based systems with 64 GB or more of physical memory, create
free lists for managing pages with physical addresses below 4 GB. This
change is to address reported problems with initializing devices that
require the allocation of physical pages below 4 GB on some systems with
128 GB or more of physical memory.
PR: 185727
Differential Revision: https://reviews.freebsd.org/D1274
Reviewed by: jhb, kib
MFC after: 3 weeks
Sponsored by: EMC / Isilon Storage Division
It's redundant at the moment since it can be obtained from the trapframe
on the architectures where DTrace is supported, but this won't be the case
with ARM.
for counter mode), and AES-GCM. Both of these modes have been added to
the aesni module.
Included is a set of tests to validate that the software and aesni
module calculate the correct values. These use the NIST KAT test
vectors. To run the test, you will need to install a soon to be
committed port, nist-kat that will install the vectors. Using a port
is necessary as the test vectors are around 25MB.
All the man pages were updated. I have added a new man page, crypto.7,
which includes a description of how to use each mode. All the new modes
and some other AES modes are present. It would be good for someone
else to go through and document the other modes.
A new ioctl was added to support AEAD modes which AES-GCM is one of them.
Without this ioctl, it is not possible to test AEAD modes from userland.
Add a timing safe bcmp for use to compare MACs. Previously we were using
bcmp which could leak timing info and result in the ability to forge
messages.
Add a minor optimization to the aesni module so that single segment
mbufs don't get copied and instead are updated in place. The aesni
module needs to be updated to support blocked IO so segmented mbufs
don't have to be copied.
We require that the IV be specified for all calls for both GCM and ICM.
This is to ensure proper use of these functions.
Obtained from: p4: //depot/projects/opencrypto
Relnotes: yes
Sponsored by: FreeBSD Foundation
Sponsored by: NetGate
Special thanks to Nicholas Esborn for the loaner router to get this
target bootstrapped.
Review: D777
Reviewed by: adrian
Sponsored by: Nicholas Esborn <nick@desert.net>
commit 6d3c4c09226ad6bdd662e3e52489ef294a6ce298
Add terasic_mtl vt(4) framebuffer driver
terasic_mtl can be built with syscons(4) and vt(4) attachments, selected
at compile time.
commit 33240259b47a7c990a5a88a19f133a5600432a4c
Clear terasic_mtl text buffer on attach
commit d188c2d2412953f949624aa35cd07082830943c9
Update terasic vt(4) driver for FreeBSD r269783
commit d1cc54eee852fa4fc9d359d5bb2171d24ec73369
Safety belt to ensure vt(4) fb parameters are correct
commit 76e6d468ef45711d7952786095fc4791289ebb4b
Improve terasic_mtl_vt fdt parsing
- Use OF_getencprop to avoid need for explicit endian handling
(submitted by ray@freebsd.org)
- Check for expected length and correct pointer type
commit 3e2524b8995ab66e8a9295e4c87cbc7126eeddf4
Correct device_printf usage
commit 9e53e3c8e0766414e25662c95b09cc51c92443b0
Switch framebuffer to match host endianness
Xorg and xf86-video-scfb work much better with a native-endian
framebuffer.
commit 0f49259d596321ed85288ac0e1fb4ee1c966df48
Switch DE4 to vt(4) and enable kbdmux
commit 5bc96ebc89db7d134ad478335090c8477c1677c7
Add missing \n in device_printf calls
Submitted by: emaste
Sponsored by: DARPA, AFRL
This change saves/restores the callee-saved MIPS floating point
registers as documented by the o32/n32/n64 spec ("MIPSpro N32
ABI Handbook", Table 2-1) for the _setjmp(3), _longjmp(3),
setjmp(3) and longjmp(3) C library functions. This is only
included when the C library is built with hardware floating point
support (or when "SOFTFLOAT" is not defined).
Submitted by: sson
MFC after: 1 month
Sponsored by: DARPA, AFRL
have chosen different (and more traditional) stateless/statuful
NAT64 as translation mechanism. Last non-trivial commits to both
faith(4) and faithd(8) happened more than 12 years ago, so I assume
it is time to drop RFC3142 in FreeBSD.
No objections from: net@
unit 0.
It seems that this 'simplification' was copied to all GPIO drivers in tree.
This fix a bug where a GPIO controller could fail to attach its children
(gpioc and gpiobus) if another GPIO driver attach first.
and casuword(9), but do not mix value read and indication of fault.
I know (or remember) enough assembly to handle x86 and powerpc. For
arm, mips and sparc64, implement fueword() and casueword() as wrappers
around fuword() and casuword(), which means that the functions cannot
distinguish between -1 and fault.
On architectures where fueword() and casueword() are native, implement
fuword() and casuword() using fueword() and casuword(), to reduce
assembly code duplication.
Sponsored by: The FreeBSD Foundation
Tested by: pho
MFC after: 2 weeks (ia64 needs treating)
- Wrong integer type was specified.
- Wrong or missing "access" specifier. The "access" specifier
sometimes included the SYSCTL type, which it should not, except for
procedural SYSCTL nodes.
- Logical OR where binary OR was expected.
- Properly assert the "access" argument passed to all SYSCTL macros,
using the CTASSERT macro. This applies to both static- and dynamically
created SYSCTLs.
- Properly assert the the data type for both static and dynamic
SYSCTLs. In the case of static SYSCTLs we only assert that the data
pointed to by the SYSCTL data pointer has the correct size, hence
there is no easy way to assert types in the C language outside a
C-function.
- Rewrote some code which doesn't pass a constant "access" specifier
when creating dynamic SYSCTL nodes, which is now a requirement.
- Updated "EXAMPLES" section in SYSCTL manual page.
MFC after: 3 days
Sponsored by: Mellanox Technologies
in userland rename in-kernel getenv()/setenv() to kern_setenv()/kern_getenv().
This fixes a namespace collision with libc symbols.
Submitted by: kmacy
Tested by: make universe
There's a bug in the AR7240 PCIe hardware where a correct BAR will end
up having the device disappear.
It turns out that for the device address it should be all 0's.
However, this meant that the PCI probe code would try writing 0xffffffff
in to see how big the window was, read back 0x0, and think the window
was 32 bits. It then ended up calculating a resource size of 0 bytes,
failed to find anything via an rman call, and this would fail to attach.
I have quite absolutely no idea how in the various planes of existence
this particular bit of code and how it worked with the PCI bus code
ever worked. But, well, it did.
Tested:
* Atheros AP93 - AR7240 + AR9280 reference board
It was doing incorrect things with masks. This was fixed in the
AR71xx codebase but it wasn't yet fixed in the AR724x code.
This ended up having config space reads return larger/incorrect values
in some situations.
Tested:
* AR7240
TODO:
* test ar7241, AR7242, and AR934x.
node's interrupts=<...> property creating resource list entries with a
single common implementation. This change makes ofw_bus_intr_to_rl() the
one true copy of that code and removes the copies of it from other places.
This also adds handling of the interrupts-extended property, which allows
specifying multiple interrupts for a node where each interrupt can have a
separate interrupt-parent. The bindings for this state that the property
cells contain an xref phandle to the interrupt parent followed by whatever
interrupt info that parent normally expects. This leads to having a
variable number of icells per interrupt in the property. For example you
could have <&intc1 1 &intc2 26 9 0 &intc3 9 4>.
Differential Revision: https://reviews.freebsd.org/D803
When the FreeBSD kernel is loaded from Xen the symtab and strtab are
not loaded the same way as the native boot loader. This patch adds
three new global variables to ddb that can be used to specify the
exact position and size of those tables, so they can be directly used
as parameters to db_add_symbol_table. A new helper is introduced, so callers
that used to set ksym_start and ksym_end can use this helper to set the new
variables.
It also adds support for loading them from the Xen PVH port, that was
previously missing those tables.
Sponsored by: Citrix Systems R&D
Reviewed by: kib
ddb/db_main.c:
- Add three new global variables: ksymtab, kstrtab, ksymtab_size that
can be used to specify the position and size of the symtab and
strtab.
- Use those new variables in db_init in order to call db_add_symbol_table.
- Move the logic in db_init to db_fetch_symtab in order to set ksymtab,
kstrtab, ksymtab_size from ksym_start and ksym_end.
ddb/ddb.h:
- Add prototype for db_fetch_ksymtab.
- Declate the extern variables ksymtab, kstrtab and ksymtab_size.
x86/xen/pv.c:
- Add support for finding the symtab and strtab when booted as a Xen
PVH guest. Since Xen loads the symtab and strtab as NetBSD expects
to find them we have to adapt and use the same method.
amd64/amd64/machdep.c:
arm/arm/machdep.c:
i386/i386/machdep.c:
mips/mips/machdep.c:
pc98/pc98/machdep.c:
powerpc/aim/machdep.c:
powerpc/booke/machdep.c:
sparc64/sparc64/machdep.c:
- Use the newly introduced db_fetch_ksymtab in order to set ksymtab,
kstrtab and ksymtab_size.
than u_char.
Migrate post_filter to use an int for a CPU rather than u_char.
Change intr_event_bind() to use an int for CPU rather than u_char.
It touches the ppc, sparc64, arm and mips machdep code but it should
(hah!) be a no-op.
Tested:
* i386, AMD64 laptops
Reviewed by: jhb
Prevent saturattion of the bus by constant polling which in
extreme cases can cause interface lockup. This makes FreeBSD
match similar case in the executive.
mapping size (currently unused). The flags includes the fault access
bits, wired flag as PMAP_ENTER_WIRED, and a new flag
PMAP_ENTER_NOSLEEP to indicate that pmap should not sleep.
For powerpc aim both 32 and 64 bit, fix implementation to ensure that
the requested mapping is created when PMAP_ENTER_NOSLEEP is not
specified, in particular, wait for the available memory required to
proceed.
In collaboration with: alc
Tested by: nwhitehorn (ppc aim32 and booke)
Sponsored by: The FreeBSD Foundation and EMC / Isilon Storage Division
MFC after: 2 weeks
The MD allocators were very common, however there were some minor
differencies. These differencies were all consolidated in the MI allocator,
under ifdefs. The defines from machine/vmparam.h turn on features required
for a particular machine. For details look in the comment in sys/sf_buf.h.
As result no MD code left in sys/*/*/vm_machdep.c. Some arches still have
machine/sf_buf.h, which is usually quite small.
Tested by: glebius (i386), tuexen (arm32), kevlo (arm32)
Reviewed by: kib
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
We continue to use pmap_enter() for that. For unwiring virtual pages, we
now use pmap_unwire(), which unwires a range of virtual addresses instead
of a single virtual page.
Sponsored by: EMC / Isilon Storage Division
be able to claim I know how the UART code works."
* Just return 115200 as the current baud rate. I should cache it in the
device struct and return that but I'm lazy right now.
* don't error out on other ioctl settings for now, just silently ignore them.
* remove some code that was copied from the 8250 driver that isn't needed
any longer.
Tested:
* AR9331, Carambola-2 board.
This commit does not add error returns to minidumpsys() or
textdump_dumpsys(); those can also be added later.
Submitted by: Conrad Meyer (EMC / Isilon storage division)
the upstream implementation and helps ensure that a trap induced by tracing
fbt::trap:entry is handled without recursively generating another trap.
This makes it possible to run most (but not all) of the DTrace tests under
common/safety/ without triggering a kernel panic.
Submitted by: Anton Rang <anton.rang@isilon.com> (original version)
Phabric: D95
several reasons for this change:
pmap_change_wiring() has never (in my memory) been used to set the wired
attribute on a virtual page. We have always used pmap_enter() to do that.
Moreover, it is not really safe to use pmap_change_wiring() to set the wired
attribute on a virtual page. The description of pmap_change_wiring() says
that it assumes the existence of a mapping in the pmap. However, non-wired
mappings may be reclaimed by the pmap at any time. (See pmap_collect().)
Many implementations of pmap_change_wiring() will crash if the mapping does
not exist.
pmap_unwire() accepts a range of virtual addresses, whereas
pmap_change_wiring() acts upon a single virtual page. Since we are
typically unwiring a range of virtual addresses, pmap_unwire() will be more
efficient. Moreover, pmap_unwire() allows us to unwire superpage mappings.
Previously, we were forced to demote the superpage mapping, because
pmap_change_wiring() only allowed us to express the unwiring of a single
base page mapping at a time. This added to the overhead of unwiring for
large ranges of addresses, including the implicit unwiring that occurs at
process termination.
Implementations for arm and powerpc will follow.
Discussed with: jeff, marcel
Reviewed by: kib
Sponsored by: EMC / Isilon Storage Division
handle packets up to 1536 bytes)
This fixes the need to frag that could happen when using vlans on top of
if_arge (which is a common case for the use the switch ports as individual
NICs).
Previously to this commit any vlan setup with if_arge as parent would have
the MTU of the parent interface reduced by the size of dot1q header
(4 bytes).
Tested on TP-Link 1043ND (where the WAN port is just a switch port setup to
tag packets in a different VLAN than the LAN ports).
Reported and tested by: Harm Weites (harm at weites.com)
These changes prevent sysctl(8) from returning proper output,
such as:
1) no output from sysctl(8)
2) erroneously returning ENOMEM with tools like truss(1)
or uname(1)
truss: can not get etype: Cannot allocate memory
there is an environment variable which shall initialize the SYSCTL
during early boot. This works for all SYSCTL types both statically and
dynamically created ones, except for the SYSCTL NODE type and SYSCTLs
which belong to VNETs. A new flag, CTLFLAG_NOFETCH, has been added to
be used in the case a tunable sysctl has a custom initialisation
function allowing the sysctl to still be marked as a tunable. The
kernel SYSCTL API is mostly the same, with a few exceptions for some
special operations like iterating childrens of a static/extern SYSCTL
node. This operation should probably be made into a factored out
common macro, hence some device drivers use this. The reason for
changing the SYSCTL API was the need for a SYSCTL parent OID pointer
and not only the SYSCTL parent OID list pointer in order to quickly
generate the sysctl path. The motivation behind this patch is to avoid
parameter loading cludges inside the OFED driver subsystem. Instead of
adding special code to the OFED driver subsystem to post-load tunables
into dynamically created sysctls, we generalize this in the kernel.
Other changes:
- Corrected a possibly incorrect sysctl name from "hw.cbb.intr_mask"
to "hw.pcic.intr_mask".
- Removed redundant TUNABLE statements throughout the kernel.
- Some minor code rewrites in connection to removing not needed
TUNABLE statements.
- Added a missing SYSCTL_DECL().
- Wrapped two very long lines.
- Avoid malloc()/free() inside sysctl string handling, in case it is
called to initialize a sysctl from a tunable, hence malloc()/free() is
not ready when sysctls from the sysctl dataset are registered.
- Bumped FreeBSD version to indicate SYSCTL API change.
MFC after: 2 weeks
Sponsored by: Mellanox Technologies
configs. Switch the BERI_NETFPGA_MDROOT to 64bit by default.
Give we have working interrupts also cleanup the extra polling CFLAGS from
the module Makefile.
MFC after: 2 weeks
the queue where to enqueue pages that are going to be unwired.
- Add stronger checks to the enqueue/dequeue for the pagequeues when
adding and removing pages to them.
Of course, for unmanaged pages the queue parameter of vm_page_unwire() will
be ignored, just as the active parameter today.
This makes adding new pagequeues quicker.
This change effectively modifies the KPI. __FreeBSD_version will be,
however, bumped just when the full cache of free pages will be
evicted.
Sponsored by: EMC / Isilon storage division
Reviewed by: alc
Tested by: pho
In particular, don't check the value of the bus_dma map against NULL
to determine if either bus_dmamem_alloc() or bus_dmamap_load() succeeded.
Instead, assume that bus_dmamap_load() succeeeded (and thus that
bus_dmamap_unload() should be called) if the bus address for a resource
is non-zero, and assume that bus_dmamem_alloc() succeeded (and thus
that bus_dmamem_free() should be called) if the virtual address for a
resource is not NULL.
In many cases these bugs could result in leaks when a driver was detached.
Reviewed by: yongari
MFC after: 2 weeks
- Update FDT file for BERI DE4 boards.
- Add needed kernel configuration keywords.
- Rename module to saf1761otg so that the device unit number does not
interfere with the hardware ID in dmesg.
Sponsored by: DARPA, AFRL
the GPIO pin is connected to a push button (or other devices).
Instead keep the boot loader settings.
Calling ar71xx_gpio_pin_configure() with DEFAULT_CAPS was probably a
mistake and was causing all the pins to be set as outputs.
at that time, but AFAIK it is only used on routerboards.
Enabling GPIO_FUNC_SPI_CS[1|2]_EN will claim the use of gpio pins 0 and 1
respectivelly for use as SPI CS pins.
When really needed, this can still be enabled on kernel hints using the
function_set and function_clear knobs.
This is derived from the mps(4) driver, but it supports only the 12Gb
IT and IR hardware including the SAS 3004, SAS 3008 and SAS 3108.
Some notes about this driver:
o The 12Gb hardware can do "FastPath" I/O, and that capability is included in
this driver.
o WarpDrive functionality has been removed, since it isn't supported in
the 12Gb driver interface.
o The Scatter/Gather list handling code is significantly different between
the 6Gb and 12Gb hardware. The 12Gb boards support IEEE Scatter/Gather
lists.
Thanks to LSI for developing and testing this driver for FreeBSD.
share/man/man4/mpr.4:
mpr(4) man page.
sys/dev/mpr/*:
mpr(4) driver files.
sys/modules/Makefile,
sys/modules/mpr/Makefile:
Add a module Makefile for the mpr(4) driver.
sys/conf/files:
Add the mpr(4) driver.
sys/amd64/conf/GENERIC,
sys/i386/conf/GENERIC,
sys/mips/conf/OCTEON1,
sys/sparc64/conf/GENERIC:
Add the mpr(4) driver to all config files that currently
have the mps(4) driver.
sys/ia64/conf/GENERIC:
Add the mps(4) and mpr(4) drivers to the ia64 GENERIC
config file.
sys/i386/conf/XEN:
Exclude the mpr module from building here.
Submitted by: Steve McConnell <Stephen.McConnell@lsi.com>
MFC after: 3 days
Tested by: Chris Reeves <chrisr@spectralogic.com>
Sponsored by: LSI, Spectra Logic
Relnotes: LSI 12Gb SAS driver mpr(4) added
platforms which do not use loaders or kernels that want to hardcode
options or for FDT passed in by loader.
Also fix a build issue by putting the kmdp variable accessed back under
the #ifdef FDT; we may wish to revisit decision in which case more
code needs changing.
Submitted by: brooks
the cpufreq code. Replace its use with smp_started. There's at least
one userland tool that still looks at the kern.smp.active sysctl, so
preserve it but point it to smp_started as well.
Discussed with: peter, jhb
MFC after: 3 days
Obtained from: Netflix
commit 003649d9622ce252a2794ae5891ee7e7c209caca
Author: Robert N. M. Watson <robert.watson@cl.cam.ac.uk>
Date: Wed Feb 5 18:32:09 2014 +0000
Teach the FreeBSD/beri boot to "auto-detect" whether argument 4 (a3) is a
memory size of pointer to a struct bootinfo * by looking at its value and
seeing whether it is pointer-like. If a pointer, assume it's a bootinfo
and extract memsize from it instead; otherwise, use it as memsize directly.
This allows kernels to support bootinfo being passed by loader (and boot2)
while still supporting older Miniboot setups.
commit f7045af9a1e92b6bd92541fe5d25abf66d824e8f
Author: Robert N. M. Watson <robert.watson@cl.cam.ac.uk>
Date: Thu Feb 6 13:45:34 2014 +0000
When the module metadata pointer is available from loader, use it in the
kernel.
commit 52e0e1ff2cba9dfcfab9e1d0a31fb7fdf7317450
Author: Robert N. M. Watson <robert.watson@cl.cam.ac.uk>
Date: Thu Feb 6 19:57:48 2014 +0000
In the BERI kernel boot code, extract 'boothowto' (which includes boot flags
such as '-s') and 'envp' from passed module data. Booting to single-user
mode using boot flags now works.
Sponsored by: DARPA, AFRL
boot/mips/beri/loader/metadata.c allow FDT configuration to set
command line options.
This leads to an interesting quesiton of future interactions with loader.
However for configurations without loader this allows bootverbose or boot
single user to be set by compiling a new kernel, which is good enough for
testing and debugging.
Reviewed by: rwatson
MFC after: 1 week
NetFPGA-10G Embedded CPU Ethernet Core.
The current version operates on a simple PIO based interface connected
to a NetFPGA-10G port.
To avoid confusion: this driver operates on a CPU running on the FPGA,
e.g. BERI/mips, and is not suited for the PCI host interface.
MFC after: 1 week
Relnotes: yes
Sponsored by: DARPA/AFRL
Remove the uart support in favour of a "jtag-uart" interface imitation
providing a much simpler interface, directly exported to the host,
allowing the toolchain to be shared with BERI on Altera. [1]
Submitted by: Jong Hun HAN (jong.han cl.cam.ac.uk) [1]
MFC after: 2 weeks
To reduce the diff struct pcu.cnt field was not renamed, so
PCPU_OP(cnt.field) is still used. pc_cnt and pcpu are also used in
kvm(3) and vmstat(8). The goal was to not affect externally used KPI.
Bump __FreeBSD_version_ in case some out-of-tree module/code relies on the
the global cnt variable.
Exp-run revealed no ports using it directly.
No objection from: arch@
Sponsored by: EMC / Isilon Storage Division
The NetBSD Foundation states "Third parties are encouraged to change the
license on any files which have a 4-clause license contributed to the
NetBSD Foundation to a 2-clause license."
This change removes clauses 3 and 4 from copyright / license blocks that
list The NetBSD Foundation as the only copyright holder.
Sponsored by: The FreeBSD Foundation
chips have more.
So for now, let's allow more. We should teach the apb code to just
reject interrupts that lie outside what the chip can do at runtime.
later. If the interrupts are ACKed even if they're not masked, we get
the interrupts again later. Grr.
* The AR724x and later chips want the interrupt bits cleared by writing the
relevant bit to it, NOT by writing all but the current interrupt to it.
Tested:
* AR9344, DB120 reference board
TODO:
* Test ar724x and later chips to ensure no regressions have occured.
'eeprommac'.
The existing driver would just make arge units past 0 take the primary
MAC and increment it by the unit number, without correct address wrapping.
That has to be fixed at a later date.
Tested:
* Atheros DB120 reference obard
IPX was a network transport protocol in Novell's NetWare network operating
system from late 80s and then 90s. The NetWare itself switched to TCP/IP
as default transport in 1998. Later, in this century the Novell Open
Enterprise Server became successor of Novell NetWare. The last release
that claimed to still support IPX was OES 2 in 2007. Routing equipment
vendors (e.g. Cisco) discontinued support for IPX in 2011.
Thus, IPX won't be supported in FreeBSD 11.0-RELEASE.
interface, in the r241616 a crutch was provided. It didn't work well, and
finally we decided that it is time to break ABI and simply make if_baudrate
a 64-bit value. Meanwhile, the entire struct if_data was reviewed.
o Remove the if_baudrate_pf crutch.
o Make all fields of struct if_data fixed machine independent size. The
notion of data (packet counters, etc) are by no means MD. And it is a
bug that on amd64 we've got a 64-bit counters, while on i386 32-bit,
which at modern speeds overflow within a second.
This also removes quite a lot of COMPAT_FREEBSD32 code.
o Give 16 bit for the ifi_datalen field. This field was provided to
make future changes to if_data less ABI breaking. Unfortunately the
8 bit size of it had effectively limited sizeof if_data to 256 bytes.
o Give 32 bits to ifi_mtu and ifi_metric.
o Give 64 bits to the rest of fields, since they are counters.
__FreeBSD_version bumped.
Discussed with: emax
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
There's plenty of hints that I haven't yet fleshed out and are hardcoded
in arswitch_8327.c. They're listed here (from OpenWRT) for completeness.
This is enough to get the thing up, running and pinging.
Note that the mdiobus for the on-switch switch changes - the AR8327
probes first, which exposes mdio1, and thus the arge1 mdiobus will probe
and attach as mdio2. That is what the AR9344 on-chip switch has to
attach to.
Tested:
* Qualcomm Atheros DB120
The on-board NIC is an 3x3 AR9380 with 5GHz only.
* enable pci code in AR9344_BASE
* enable ath_pci and the firmware loading bits in DB120
* add in the relevant hints in DB120.hints to inform the probe/attach
code where the PCIe fixup data is for the onboard chip.
This is only relevant for a default development board. I also have a
DB120 with the on-board PCIe wifi NIC disabled and it's exposed as
a real PCIe slot (to put normal PCIe NICs in); the fixup code will need
to be disabled to make this work correctly.
Tested:
* DB120
