Summary:
Both booke and AIM interrupt.c files contain nearly identical code. This merges
the two files, to reduce duplication.
Reviewers: #powerpc, marcel
Reviewed By: marcel
Subscribers: imp
Differential Revision: https://reviews.freebsd.org/D2991
bd_hdrcmplt. As if_loop does not use link-level headers, its behavior
when used by bpfwrite() should be the same regardless of the state of
bd_hdrcmplt. Without this change, libpcap (and other BPF users that
work like it) fail when writing to loopback interfaces.
Differential Revision: https://reviews.freebsd.org/D2989
Reviewed by: gnn, melifaro
Approved by: jmallett (mentor)
MFC after: 3 days
This obviates the need for a MNTK_SUSPENDABLE flag, since passthrough
filesystems like nullfs and unionfs no longer need to inherit this
information from their lower layer(s). This change also restores the
pre-r273336 behaviour of using the presence of a susp_clean VFS method to
request suspension support.
Reviewed by: kib, mjg
Differential Revision: https://reviews.freebsd.org/D2937
To avoid conflicts between target and initiator devices in CAM, make
CTL use target ID reported by HBA as its initiator_id in XPT_PATH_INQ.
That target ID is known to never be used for initiator role, so it won't
conflict. For Fibre Channel and FireWire HBAs this specific ID choice
is irrelevant since all target IDs there are virtual. Same time for SPI
HBAs it seems could be even requirement to use same target ID for both
initiator and target roles.
While there are some more things to polish in isp(4) driver, first tests
of using both roles same time on the same port appeared successfull:
# camcontrol devlist -v
scbus0 on isp0 bus 0:
<FREEBSD CTLDISK 0001> at scbus0 target 1 lun 0 (da20,pass21)
<> at scbus0 target 256 lun 0 (ctl0)
<> at scbus0 target -1 lun ffffffff (ctl1)
FreeBSD never had limitation on number of target IDs, and there is no
any other requirement to allocate them densely. Since slots of port
database already populated just sequentially, there is no much need
for another indirection to allocate sequentially too.
On Book-E, physical addresses are actually 36-bits, not 32-bits. This is
currently worked around by ignoring the top bits. However, in some cases, the
boot loader configures CCSR to something above the 32-bit mark. This is stage 1
in updating the pmap to handle 36-bit physaddr.
This will print out the Memory Subsystem Status Register on MPC745x (G4+ class),
and the Machine Check Status Register on Book-E class CPUs, to aid in debugging
machine checks. Other relevant registers, for other CPUs, can be added in the
future.
directory sys/contrib/libnv.
The goal of this operation is to NOT install header files which shouldn't
be used outside the nvlist library.
Approved by: pjd (mentor)
make the find it does extremely expensive, so compute it only
once. Also make sure the 'traditional' module building method works at
the expense of a bit of duplicated code.
and start teaching subsystems about it.
The Atheros MIPS platforms don't guarantee any kind of FIFO consistency
with interrupts in hardware. So software needs to do a flush when it
receives an interrupt and before it calls the interrupt handler.
There are new ones for the QCA934x and QCA955x, so do a few things:
* Get rid of the individual ones (for ethernet and IP2);
* Create a mux and enum listing all the variations on DDR flushes;
* replace the uses of IP2 with the relevant one (which will typically
be "PCI" here);
* call the USB DDR flush before calling the real USB interrupt handlers;
* call the ethernet one upon receiving an interrupt that's for us,
rather than never calling it during operation.
Tested:
* QCA9558 (TP-Link archer c7 v2)
* AR9331 (Carambola 2)
TODO:
* PCI, USB, ethernet, etc need to do a double-check to see if the
interrupt was truely for them before doing the DDR. For now I
prefer "correct" over "fast".
This stops the panics that occur on MIPS platforms when doing say,
'sysctl dev.ath.0' whilst the MAC is asleep. The MIPS platform is
rather unforgiving in getting power-save register access wrong and you
will get all kinds of odd failures if you don't have things woken
up at the right times.
Tested:
* QCA9558 (TP-Link Archer C7 v2)
* AR9331 (Carambola 2)
.. with no VAPs configured and ath0 down (thus the MAC is definitely
asleep.)
PR: kern/201117
the kernel would generate a bogus one with a ":/<path>" suffix.
This would only occur for the case where there was no explicit
"principal" argument and the getaddrinfo() call in mount_nfs.c failed to a
return a cannonical name for the server.
This patch fixes this unusual case.
PR: 201073
Submitted by: masato@itc.naist.jp
MFC after: 2 weeks
Update setkey and libipsec to understand aes-gcm-16 as an
encryption method.
A partial commit of the work in review D2936.
Submitted by: eri
Reviewed by: jmg
MFC after: 2 weeks
Sponsored by: Rubicon Communications (Netgate)
change to GMAC easier on A20 SoCs.
On A10 only the EMAC controller is available (fast ethernet), but on A20
there is also GMAC a high (or better) performant controller (gigabit
ethernet).
On A20 the both controllers uses the same pins to talk to the ethernet PHY
(MII or RGMII) and they can be selected by the GPIO pin mux.
There is work in progress to bring in GMAC support.
When IPSEC is enabled on the kernel the forwarding path has an optimization to not enter the code paths
for checking security policies but first checks if there is any security policy active at all.
The patch introduces the same optimization but for traffic generated from the host itself.
This reduces the overhead by 50% on my tests for generated host traffic without and SP active.
Differential Revision: https://reviews.freebsd.org/D2980
Reviewed by: ae, gnn
Approved by: gnn(mentor)
