This makes Mac OS X happy when it returns back from suspending.
o Switch notify state after data is transferred, but not before.
o Consider there is also Super Speed mode.
o Do not set stall bit on any pipes in device mode as Mac OS X seems
don't support it.
In collaboration with: hselasky@
driver on Rockchip boards. It currently supports PIO mode
and dma mode needs external dma controller to be used.
Submitted by: jmcneill
Approved by: stas (mentor)
"MODULE_VERSION" macro definition. Remove the redefinition of the
"MODULE_VERSION" macro from the Linux kernel compatibility API.
MFC after: 1 month
Reported by: np@
Sponsored by: Mellanox Technologies
bits.
The motivation here is to eventually teach netisr and potentially
other networking subsystems a bit more about how RSS work queues / buckets
are configured so things have a hope of auto-configuring in the future.
* net/rss_config.[ch] takes care of the generic bits for doing
configuration, hash function selection, etc;
* topelitz.[ch] is now in net/ rather than netinet/;
* (and would be in libkern if it didn't directly include RSS_KEYSIZE;
that's a later thing to fix up.)
* netinet/in_rss.[ch] now just contains the IPv4 specific methods;
* and netinet/in6_rss.[ch] now just contains the IPv6 specific methods.
This should have no functional impact on anyone currently using
the RSS support.
Differential Revision: D1383
Reviewed by: gnn, jfv (intel driver bits)
accidentally enable non-existent states.
This bug was triggered if ACPI advertises the presence of a C2 state
which we fail to parse via acpi_PkgGas due to our lack of support for
FFixedHW resources, and causes an immediate panic when an attempt is
made to enter the (NULL) state.
One affected platform is the EC2 c4.8xlarge VM instance type; there
may be others.
MFC after: 1 week
Thanks to: jkim, @_msw_
sdhci controllers, such as the one on a Raspberry Pi, mishandle the signal
timing in high speed signaling mode, but run just fine in standard mode
with the bus running at frequencies between 25-50MHz (which shouldn't work).
This is the solution adopted by U-Boot and other OSes (linux and *BSD)
for the timeouts on Raspberry Pi boards with certain SD cards. Some
research shows that this quirk is also used on a few other boards, so the
fix is a generic quirk instead of being in the RPi-specific driver code.
This change is based on information discovered by Michal Meloun.
Required when communicating to Mac OS X USB host stack.
o Also don't set stall bit to TX pipe in device mode as seems Mac OS X
don't clears it as it should.
Discussed with: hselasky@
in prep for the next NF calibration pass.
Totally missing braces. Damn you C.
Submitted by: Sascha Wildner <swildner@dragonflybsd.org>
MFC after: 1 week
MCI bluetooth coexistence method for WB222.
The rest of MCI requires a bunch more work, including adding a DMA buffer
for the MCI hardware to bounce messages in/out of and handling MCI
interrupts. But the more important part here is telling the HAL
the btcoex is enabled and MCI is in use so it configures the correct
initial bluetooth parameters in the wireless NIC and configures
things like bluetooth traffic weights and such.
So, this at least gets the HAL to do some of the right things in
configuring the inital bluetooth coexistence stuff, but doesn't
actually do full btcoex. That'll take.. some effort.
Tested:
* AR9462 (WB222), STA mode
tree's /chosen node to provide out-of-band header fields of the FDT. This
emulation is not perfect without corresponding changes to ofw_fdt_nextprop(),
but is enough to enable lookup by memory-map-parsing code.
MFC after: 1 week
resume sometimes (but not others). On powerup, other wierd issues show
up (sometimes the card comes up, but with really bogus pci config
space stuff. There may be more, but given my experience of historical
fussiness, stick to what works and make more minimal changes to that.
go back through HASWELL, IVY_BRIDGE, IVY_BRIDGE_XEON and SANDY_BRIDGE
to straighten out all the missing PMCs. We also add a new pmc tool
pmcstudy, this allows one to run the various formulas from
the documents "Using Intel Vtune Amplifier XE on XXX Generation platforms" for
IB/SB and Haswell. The tool also allows one to postulate your own
formulas with any of the various PMC's. At some point I will enahance
this to work with Brendan Gregg's flame-graphs so we can flamegraph
various PMC interactions. Note the manual page also needs some
work (lots of work) but gnn has committed to help me with that ;-)
Reviewed by: gnn
MFC after:1 month
Sponsored by: Netflix Inc.
can suspend / resume and unload / load cbb and cardbus without errors
on my Lenovo T400, which wasn't possible before. Cards suspending
and resuming in the CardBus slot not yet tested.
o Enable memory cycles to the bridge early (as part of the new
cbb_pci_bridge_init). This fixes the Bad VCC errors which were
caused by the code accessing the device registers with this
cleared. The suspend / resume process clears it.
o Refactor suspend / resume into bus specific code (though the ISA
code is just stubbed). This isn't strictly necessary, but makes
the initializaiton code more uniform and should be more bullet
proof in the face of variant behavior among cardbus bridges.
o Fixup comments in the power-up sequence to reflect reality. These
comments were written for one regime of power-up, but not updated
as things were revised.
o Add a paranoid small delay (100ms) to cover noisy cards powering
down.
o Fix some debugging prints to be easier to grep from dmesg.
Sponsored by: Netflix
simultaneously detaching kernel drivers on the same USB device we can
get stuck in the "usb_wait_pending_ref_locked()" function because the
conditions needed for allowing detach are not met. The "destroy_dev()"
function waits for all system calls involving the given character
device to return. Character device system calls may lock the USB
enumeration lock, which is also held when "destroy_dev()" is
called. This can sometimes lead to a deadlock not noticed by
WITNESS. The current solution is to ensure the calling thread is the
only one holding the USB enumeration lock and prevent other threads
from getting refs while a USB device detach is ongoing. This turned
out not to be sufficient. To solve this deadlock we could use
"destroy_dev_sched()" to schedule the device destruction in the
background, but then we don't know when it is safe to free() the
private data of the character device. Instead a callback function is
executed by the USB explore process to kill off any leftover USB
character devices synchronously after the USB device explore code is
finished and the USB enumeration lock is no longer locked. This makes
porting easier and also ensures us that character devices must
eventually go away after a USB device detach.
While at it ensure that "flag_iserror" is only written when "priv_mtx"
is locked, which is protecting it.
MFC after: 5 days
Before this change, the current code handles SIOCGIFADDR the same
way with SIOCSIFADDR, which involves full arp_ifinit, et al. They
should be unnecessary for SIOCGIFADDR case.
Differential Revision: https://reviews.freebsd.org/D1508
Reviewed by: glebius
MFC after: 2 weeks
Instead of reusing the same reg parsing code, create one, common function
that puts reg contents to the resource list. Address cells and size cells
are passed rather than acquired here so that any bus can have different
default values.
Obtained from: Semihalf
Reviewed by: andrew, ian, nwhitehorn
Sponsored by: The FreeBSD Foundation
driver name and NIC driver softc via the device(9) tree,
instead of going dirty through the ifnet(9) layer.
Differential Revision: D1506
Reviewed by: imp, jhb
if_ixl to version 1.3.0, if_ixlv to version 1.2.0
- Major change in both drivers is to add RSS support
- In ixl fix some interface speed related issues, dual
speed was not changing correctly, KR/X media was not
displaying correctly (this has a workaround until a
more robust media handling is in place)
- Add a warning when using Dell NPAR and the speed is
less than 10G
- Wrap a queue hung message in IXL_DEBUG, as it is non-fatal,
and without tuning can display excessively
MFC after: 1 week
unnecessary filter configuration code in nge_init_locked().
While I'm here add a check for driver running state for multicast
filter handling. Also remove unnecessary assignment to error
variable since it is cleared in the function entry.
Suggested by: brad@OpenBSD.org
