o add support for IXP435 cpu's (e.g. 64 irq's)
o add support for Cambria-specific devices: npe, led's (front panel and
octal latch), ehci, mcu, ide cf
o redo memory mapping for xscale/ixp4xx boards: previously memory
was assumed aliased to 0x10000000 but this appears to be true only
for ixp425 systems and breaks operation on others; rework so memory
is assumed to start at 0
o rework NPE configuration support to use NPE id's instead of port #'s;
these changes also rename the associated MAC's to follow the NPE's
they are attached to
o update npe firmware to latest rev (same license) and update default fw
imageid's to match; in particular this adds NPE-A and crypto support
o re-style NPE fw handling code and add a console msg identifying the
attributes of the loaded fw
o fix numerous problems with handling failures during npe setup
o fix npe rx q setup; need to spin waiting for mailbox responses during
early boot stages as qmgr interrupts are not delivered; this fixes
the problem where all 8 traffic classifications were not tied to the
rx q (and eliminates the console msg "remember to fix rx q setup")
o add DELAY to npe MII wait logic for IXP435
o strip down builtin phys->virt address translation table in resource
handling to just those resources that require it and add a console msg
to alert people when this (kludge) table needs to be extended
o purge a bunch of dead netbsd-ism's
o cleanup avila led driver
o add Cambria support to boot2 and rework code for better multi-board support
Notes:
1. NPE-A doesn't work and causes NPE-C to stop working; it is disabled
in the hints
2. USB isn't working yet; controller communicates ok but device
discovery fails
3. Cambria support must be configured separately from IXP425 boards;
multi-board support is TBD
Sponsored by: Hobnob, Gateworks (board donation)
Reviewed by: imp
o recognize ixp435 cpu
o change memory layout for for ixp4xx to not assume memory is aliases
to 0x10000000 (Cambria/ixp435 memory starts at zero)
o handle 64 irqs for ixp435
o dual EHCI USB 2.0 controller integral to ixp435
o overhaul NPE code for ixp435 and better MAC+MII naming
o updated NPE firmware (including NPE-A image for ixp435/ixp465)
o Gateworks Cambria board support:
- IDE compact flash
- MCU
- front panel LED on i2c bus
- Octal LED latch
Sanity-tested with NFS-root on Avila and Cambria boards. Requires
pending boot2 mods for CF-boot on Cambria.
module; the ath module now brings in the hal support. Kernel
config files are almost backwards compatible; supplying
device ath_hal
gives you the same chip support that the binary hal did but you
must also include
options AH_SUPPORT_AR5416
to enable the extended format descriptors used by 11n parts.
It is now possible to control the chip support included in a
build by specifying exactly which chips are to be supported
in the config file; consult ath_hal(4) for information.
machine arm
device mem
options GEOM_BSD
options GEOM_MBR
Remove the first two from all kernel configuration files and
change geom_bsd and geom_mbr from standard to optional.
FreeBSD 8-CURRENT was tested and run successfully on the following eval
boards and devices :
* DB-88F5182, DB-88F5281 (Orion based)
* DB-88F6281, RD-88F6281 (Kirkwood based)
* DB-78100 (Discovery based)
For more detailed info on build instructions and other examples please refer
to http://wiki.freebsd.org/FreeBSDMarvell
Obtained from: Marvell, Semihalf
don't inline the locking primitives, and only grab those parts of mii
that we really need. Other space optimizations are too agressive for
the generic file (removing all of usb, and loading it as kernel
modules).
o It has been tested only on KB9202, KB9202A and KB9202B boards
o Better comments about hints
o option<space><tab>
o Add newer SX_NOINLINE option.
o Fix a few comments
As clearly mentioned on the mailing lists, there is a list of drivers
that have not been ported to the MPSAFE TTY layer yet. Remove them from
the kernel configuration files. This means people can now still use
these drivers if they explicitly put them in their kernel configuration
file, which is good.
People should keep in mind that after August 10, these drivers will not
work anymore. Even though owners of the hardware are capable of getting
these drivers working again, I will see if I can at least get them to a
compilable state (if time permits).
don't support the ioapic either, so remove that option too. These
were commented out, but could never be enabled, unlike the other
options in the file that are commented out.
boards. This is enough to net-boot to multiuser.
Also supported is the SMSC LAN91C111 parts used on the netCF, netDUO and netMMC
add-on boards.
I'll be putting some instructions on how to boot this on the Gumstix boards
online soon.
This is still fairly rough and will be refined over time but I felt it was
better to get this out there where other people can help out.
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
to detect (or load) kernel NLM support in rpc.lockd. Remove the '-k'
option to rpc.lockd and make kernel NLM the default. A user can still
force the use of the old user NLM by building a kernel without NFSLOCKD
and/or removing the nfslockd.ko module.
While the KSE project was quite successful in bringing threading to
FreeBSD, the M:N approach taken by the kse library was never developed
to its full potential. Backwards compatibility will be provided via
libmap.conf for dynamically linked binaries and static binaries will
be broken.
After discussion with Sam, switch back to use firmware(9) instead of
having the firmware in hex format.
Put the binary firmware uuencoded into sys/contrib/dev/npe, and slap a
LICENSE file, as found on the Intel website.
Approved by: re (blanket), mux (mentor)
MFC After: 1 week
only USB 1.1 speeds available, but this shouldn't hurt. Now that we have
working usb support for this board, this is a natural followup.
Approved by: re (kensmith)
FreeBSD/arm installworld install is only 170MB. The smallest SD card
I could find at the store today was 512MB (and it was only $10 after
rebate), with a 2GB card for as low as $25.00...
Now that the IIC stuff has been sorted out, include that as well.
Include hints for the icee 16kb 16-bit i2c device. It should include
info about the temperature sensor as well, but that driver isn't quite
ready.
Add bpf for dhclient happiness.
MFC After: 1 week
mapped at, and LOADERRAMADDR, the address at which the loader maps the ram at
at the time the kernel is booted.
They are used to detect if the kernel is booted from the onboard flash.
Define those for the IQ31244
partitioning class that supports multiple schemes. Current
schemes supported are APM (Apple Partition Map) and GPT.
Change all GEOM_APPLE anf GEOM_GPT options into GEOM_PART_APM
and GEOM_PART_GPT (resp).
The ctlreq interface supports verbs to create and destroy
partitioning schemes on a disk; to add, delete and modify
partitions; and to commit or undo changes made.
The 'nooption' kernel config entry has to be used to turn KSE off now.
This isn't my preferred way of dealing with this, but I'll defer to
scottl's experience with the io/mem kernel option change and the grief
experienced over that.
Submitted by: scottl@
