Remove the magic mfi_array is 288 bytes and just use the
sizeof the array since it is not 288 bytes.
Change reporting of a "SYSTEM" disk to "JBOD" to match
LSI MegaCli and firmware reporting.
This means that fiutil command to "create jbod" is now a
little confusing since a RAID per drive is not really what
LSI defines JBOD to be. This should be fixed in the future
and support added to really create LSI JBOD and enable that
feature on cards that support it.
First cut of new HW support from LSI and merge into FreeBSD.
Supports Drake Skinny and ThunderBolt cards.
MFhead_mfi r227574
Style
MFhead_mfi r227579
Use bus_addr_t instead of uintXX_t.
MFhead_mfi r227580
MSI support
MFhead_mfi r227612
More bus_addr_t and remove "#ifdef __amd64__".
MFhead_mfi r227905
Improved timeout support from Scott.
MFhead_mfi r228108
Make file.
MFhead_mfi r228208
Fixed botched merge of Skinny support and enhanced handling
in call back routine.
MFhead_mfi r228279
Remove superfluous !TAILQ_EMPTY() checks before TAILQ_FOREACH().
MFhead_mfi r228310
Move mfi_decode_evt() to taskqueue.
MFhead_mfi r228320
Implement MFI_DEBUG for 64bit S/G lists.
MFhead_mfi r231988
Restore structure layout by reverting the array header to
use [0] instead of [1].
MFhead_mfi r232412
Put wildcard pattern later in the match table.
MFhead_mfi r232413
Use lower case for hexadecimal numbers to match surrounding
style.
MFhead_mfi r232414
Add more Thunderbolt variants.
MFhead_mfi r232888
Don't act on events prior to boot or when shutting down.
Add hw.mfi.detect_jbod_change to enable or disable acting
on JBOD type of disks being added on insert and removed on
removing. Switch hw.mfi.msi to 1 by default since it works
better on newer cards.
MFhead_mfi r233016
Release driver lock before taking Giant when deleting children.
Use TAILQ_FOREACH_SAFE when items can be deleted. Make code a
little simplier to follow. Fix a couple more style issues.
MFhead_mfi r233620
Update mfi_spare/mfi_array with the actual number of elements
for array_ref and pd. Change these max. #define names to avoid
name space collisions. This will require an update to mfiutil
It avoids mfiutil having to do a magic calculation.
Add a note and #define to state that a "SYSTEM" disk is really
what the firmware calls a "JBOD" drive.
Thanks to the many that helped, LSI for the initial code drop,
mav, delphij, jhb, sbruno that all helped with code and testing.
sys/dev/isci/isci_task_request.c:198:7: error: case value not in enumerated type 'SCI_TASK_STATUS' (aka 'enum _SCI_TASK_STATUS') [-Werror,-Wswitch]
case SCI_FAILURE_TIMEOUT:
^
This is because the switch is done on a SCI_TASK_STATUS enum type, but
the SCI_FAILURE_TIMEOUT value belongs to SCI_STATUS instead.
Because the list of SCI_TASK_STATUS values cannot be modified at this
time, use the simplest way to get rid of this warning, which is to cast
the switch argument to int. No functional change.
Reviewed by: jimharris
MFC after: 3 days
- Don't malloc() new MCA records for machine checks logged due to a
CMCI or MC# exception. Instead, use a pre-allocated pool of records.
When a CMCI or MC# exception fires, schedule a swi to refill the pool.
The pool is sized to hold at least one record per available machine
bank, and one record per CPU. This should handle the case of all CPUs
triggering a single bank at once as well as the case a single CPU
triggering all of its banks. The periodic scans still use malloc()
since they are run from a safe context.
- Since we have to create an swi to handle refills, make the periodic scan
a second swi for the same thread instead of having a separate taskqueue
thread for the scans.
Suggested by: mdf (avoiding malloc())
MFC after: 2 weeks
- Do not define the foo_start() methods or set if_start in the ifnet if
multiq transmit is enabled. Also, set if_transmit and if_qflush before
ether_ifattach rather than after when multiq transmit is enabled. This
helps to ensure that the drivers never try to mix different transmit
methods.
- Properly restart transmit during resume. igb(4) was not restarting it
at all, and em(4) was restarting even if the link was down and was
calling the wrong method if multiq transmit was enabled.
- Remove all the 'more' handling for transmit completions. Transmit
completion processing does not have a processing limit, so it always
runs to completion and never has more work to do when it returns.
Instead, the previous code was returning 'true' anytime there were
packets in the queue that weren't still in the process of being
transmitted. The effect was that the driver would continuously
reschedule a task to process TX completions in effect running at 100%
CPU polling the hardware until it finished transmitting all of the
packets in the ring. Now it will just wait for the next TX completion
interrupt.
- Restart packet transmission when the link becomes active.
- Fix the MSI-X queue interrupt handlers to restart packet transmission if
there are pending packets in the relevant software queue (IFQ or buf_ring)
after processing TX completions. This is the root cause for the OACTIVE
hangs as if the MSI-X queue handler drained all the pending packets from
the TX ring, nothing would ever restart it. As such, remove some
previously-added workarounds to reschedule a task to poll the TX ring
anytime OACTIVE was set.
Tested by: sbruno
Reviewed by: jfv
MFC after: 1 week
"Under a highly specific and detailed set of internal timing conditions,
the processor may incorrectly update the stack pointer after a long series
of push and/or near-call instructions, or a long series of pop and/or
near-return instructions. The processor must be in 64-bit mode for this
erratum to occur."
MFC after: 3 days
- Correctly determine the maximum payload size for setting the TX link
frequent NACK latency and replay timer thresholds.
Submitted by: stefanf [1]
MFC after: 3 days
This change also workarounds dhclient's link state handling bug by
not giving current link status.
Unlike other controllers, ale(4)'s PHY hibernation perfectly works
such that driver does not see a valid link if the controller is not
brought up. If dhclient(8) runs on ale(4) it will blindly waits
until link UP and then gives up after 10 seconds. Because
dhclient(8) still thinks interface got a valid link when IFM_AVALID
is not set for selected media, this change makes dhclient initiate
DHCP without waiting for link UP.
needs to defer link state handling.
While I'm here, mark IFF_DRV_RUNNING before changing media. If
link is established without any delay, that link state change
handling could be lost.
that revision, the bswapXX_const() macros were renamed to bswapXX_gen().
Also, bswap64_gen() was implemented as two calls to bswap32(), and
similarly, bswap32_gen() as two calls to bswap16(). This mainly helps
our base gcc to produce more efficient assembly.
However, the arguments are not properly masked, which results in the
wrong value being calculated in some instances. For example,
bswap32(0x12345678) returns 0x7c563412, and bswap64(0x123456789abcdef0)
returns 0xfcdefc9a7c563412.
Fix this by appropriately masking the arguments to bswap16() in
bswap32_gen(), and to bswap32() in bswap64_gen(). This should also
silence warnings from clang.
Submitted by: jh
revision has two problems:
- It can produce worse code with both clang and gcc.
- It doesn't fix the actual issue introduced in r232721, which will be
fixed in the next commit.
Submitted by: bde, tijl and jh
Pointy hat to: dim
regardless of whether -F (foreground) option is set or not.
Also, if -P option is specified, ignore pidfile setting from configuration
not only on start but on reload too. This fixes the issue when for hastd
run with -P option reload caused the pidfile change.
Reviewed by: pjd
MFC after: 1 week
not disable it and it is even harmful as hselasky found out. Historically,
this code was originated from (OLDCARD) CardBus driver and later leaked into
PCI driver when CardBus was newbus'ified and refactored with PCI driver.
However, it is not really necessary even for CardBus.
Reviewed by: hselasky, imp, jhb
bridges. Rather than blindly enabling the windows on all of them, only
enable the window when an MSI interrupt is enabled for a device behind
the bridge, similar to what already happens for HT PCI-PCI bridges.
To implement this, each x86 Host-PCI bridge driver has to be able to
locate it's actual backing device on bus 0. For ACPI, use the _ADR
method to find the slot and function of the device. For the non-ACPI
case, the legacy(4) driver already scans bus 0 looking for Host-PCI
bridge devices. Now it saves the slot and function of each bridge that
it finds as ivars that the Host-PCI bridge driver can then use in its
pcib_map_msi() method.
This fixes machines where non-MSI interrupts were broken by the previous
round of HT MSI changes.
Tested by: bapt
MFC after: 1 week
added, the call to pmap_kextract() was moved up, and as a result the
code never updated the physical address to use for DMA if a bounce
buffer was used. Restore the earlier location of pmap_kextract() so
it takes bounce buffers into account.
Tested by: kargl
MFC after: 1 week
Right now ath_txq_sched() is mainly called from the TX ath_tx_processq()
routine, which is (mostly) done as part of the taskqueue. It shouldn't
be called outside the taskqueue.
But now that I'm about to flip back on BAR TX, I'm going to start
stressing the ath_tx_tid_pause() and ath_tx_tid_resume() paths.
What I don't want to have happen is a reschedule of the TID traffic
_during_ the completion of TX frames.
Ideally I'd like to have a way to flag back up to the processing code
that the current hardware queue should be rechecked for software TID
queue frames. But for now, this should suffice for the BAR TX case.
I may eventually delete this code once I've brought some further
sanity to the general TX queue/completion path.
be less ambiguous and more clearly identify what it means. This
attribute is what Intel refers to as UC-, and it's only difference
relative to normal UC memory is that a WC MTRR will override a UC-
PAT entry causing the memory to be treated as WC, whereas a UC PAT
entry will always override the MTRR.
- Remove the VM_MEMATTR_UNCACHED alias from powerpc.
Don't disable BARs on any PCI display devices, because doing that can
sometimes cause the main memory bus to stop working, causing all
memory reads to return nothing but 0xFFFFFFFF, even though the memory
location was previously written. After a while a privileged
instruction fault will appear and then nothing more can be debugged.
The reason for this behaviour is unknown.
MFC after: 1 week
