Members of the syscall argument structures are padded to a word size. So,
for COMPAT_LINUX32 we should convert user supplied system call arguments
which is 32-bit in that case to the array of register_t.
Reported by: Oleg V. Nauman
MFC after: 1 week
The main lockmgr routine takes 8 arguments which makes it impossible to
tail-call it by the intermediate vop_stdlock/unlock routines.
The routine itself starts with an if-forest and reads from the lock itself
several times.
This slows things down both single- and multi-threaded. With the patch
single-threaded fstats go 4% up and multithreaded up to ~27%.
Note that there is still a lot of room for improvement.
Reviewed by: kib
Tested by: pho
This enables the PHY circuitry for UTMI+ level 2 and 3, and sets the
flag to tell the ehci code that the root hub has a transaction translator
in it. For imx6 we can use the standard ehci_get_port_speed_portsc()
function to find out what speed device is connected to the port.
This makes the code to pass whole word of the mmap(2) syscall argument
prot to the syscall helper kern_vm_mmap(), which can validate all
bits. The change provides temporal fix for sys/vm/mmap_test
mmap__bad_arguments, which was broken after r313352.
PR: 216976
Reported and tested by: ngie
Sponsored by: The FreeBSD Foundation
for maketab.c
The former simplifies pathing in make/displayed output, whereas the latter was just
unnecessarily superfluous since .PATH referenced the path to maketab.c earlier on in
the Makefile.
MFC after: 1 week
Sponsored by: Dell EMC Isilon
The condition can be hit with simple user input, so it isn't an invariant.
Just error out.
PR: 217003
Reported by: Vladislav V. Prodan <admin at support.od.ua>
Sponsored by: Dell EMC Isilon
If the TCP stack has retransmitted more than 1/4 of the total
number of retransmits before a connection drop, it decides that
its current RTT estimate is hopelessly out of date and decides
to recalculate it from scratch starting with the next ACK.
Unfortunately, it implements this by zeroing out the current RTT
estimate. Drop this hack entirely, as it makes it significantly more
difficult to debug connection issues. Instead check for excessive
retransmits at the point where srtt is updated from an ACK being
received. If we've exceeded 1/4 of the maximum retransmits,
discard the previous srtt estimate and replace it with the latest
rtt measurement.
Differential Revision: https://reviews.freebsd.org/D9519
Reviewed by: gnn
Sponsored by: Dell EMC Isilon
The efipart rework did break the ARM systems as the new code is
using more exact filters to sort the devices and we need to
add support for MEDIA_FILEPATH_DP device paths.
PR: 216940
Reported by: karl@denninger.net
Reviewed by: allanjude, manu
Approved by: allanjude (mentor)
Differential Revision: https://reviews.freebsd.org/D9520
From NetBSD christos Sat Jan 26 00:19:39 2013 +0000
make the buffer functions look exactly like the kernel ones and add other
cruft to make the kernel files compile.
ffs.c 1.54
ffs/buf.c 1.13
ffs/buf.h 1.3
ffs/ffs_alloc.c 1.21
ffs/ffs_balloc.c 1.15
Reviewed by: marcel, ngie
Obtained from: NetBSD
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D8404
The isp(4) driver was changing the tag type for REQUEST SENSE
commands to Head of Queue, when the CAM CCB flag
CAM_TAG_ACTION_VALID was NOT set. CAM_TAG_ACTION_VALID is set
when the tag action in the XPT_SCSI_IO is not CAM_TAG_ACTION_NONE
and when the target has tagged queueing turned on.
In most cases when CAM_TAG_ACTION_VALID is not set, it is because
the target is not doing tagged queueing. In those cases, trying to
send a Head of Queue tag may cause problems. Instead, default to
sending a simple tag.
IBM tape drives claim to support tagged queueing in their standard
Inquiry data, but have the DQue bit set in the control mode page
(mode page 10). CAM correctly detects that these drives do not
support tagged queueing, and clears the CAM_TAG_ACTION_VALID flag
on CCBs sent down to the drives.
This caused the isp(4) driver to go down the path of setting the
tag action to a default value, and for Request Sense commands only,
set the tag action to Head of Queue.
If an IBM tape drive does get a Head of Queue tag, it rejects it with
Invalid Message Error (0x49,0x00). (The Qlogic firmware translates that
to a Transport Error, which the driver translates to an Unrecoverable
HBA Error, or CAM_UNREC_HBA_ERROR.) So, by default, it wasn't possible
to get a good response from a REQUEST SENSE to an FC-attached IBM
tape drive with the isp(4) driver.
IBM tape drives (tested on an LTO-5 with G9N1 firmware and a TS1150
with 4470 firmware) also have a bug in that sending a command with a
non-simple tag attribute breaks the tape drive's Command Reference
Number (CRN) accounting and causes it to ignore all subsequent
commands because it and the initiator disagree about the next
expected CRN. The drives do reject the initial command with a head
of queue tag with an Invalid Message Error (0x49,0x00), but after that
they ignore any subsequent commands. IBM confirmed that it is a bug,
and sent me test firmware that fixes the bug. However tape drives in
the field will still exhibit the bug until they are upgraded.
Request Sense is not often sent to targets because most errors are
reported automatically through autosense in Fibre Channel and other
modern transports. ("Modern" meaning post SCSI-2.) So this is not
an error that would crop up frequently. But Request Sense is useful on
tape devices to report status information, aside from error reporting.
This problem is less serious without FC-Tape features turned on,
specifically precise delivery of commands (which enables Command
Reference Numbers), enabled on the target and initiator. Without
FC-Tape features turned on, the target would return an error and
things would continue on.
And it also does not cause problems for targets that do tagged
queueing, because in those cases the isp(4) driver just uses the
tag type that is specified in the CCB, assuming the
CAM_TAG_ACTION_VALID flag is set, and defaults to sending a Simple
tag action if it isn't an ordered or head of queue tag.
sys/dev/isp/isp.c:
In isp_start(), don't try to send Request Sense commands
with the Head of Queue tag attribute if the CCB doesn't
have a valid tag action. The tag action likely isn't valid
because the target doesn't support tagged queueing.
Sponsored by: Spectra Logic
MFC after: 3 days
Some recent changes to vm related to mmap(2) have broken the prot checks that
would result with an EINVAL with this case
I suspect r313352 is the root-cause the issue
PR: 216976
Sponsored by: Dell EMC Isilon
This information is less useful when the generated files are included in
source control along with the source. If needed it can be reconstructed
from the $FreeBSD$ tag in the generated file. Removing this information
from the generated output permits committing the generated files along
with the change to the system call master list without having inconsistent
metadata in the generated files.
Reviewed by: emaste, kib
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D9497
ld.bfd generates two PT_LOAD segments, but certain linkers or linker
configurations generate three PT_LOAD segments (one additional for
RELRO).
PR: 216975
Reported by: Shawn Webb
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
