- In wb_rxeof(), if the received packet is less than MINCLSIZE bytes,
copy it to an mbuf chain so as to be more frugal in our use of mbuf
clusters.
- The Winbond chip, like the ASIX, wants the 'TX interrupt request'
bit set in the _first_ fragment of a transmitted frame, not the
last. (At least the Winbond manual states this unambiguously; too
bad I wasn't paying attention when I read it the first time.)
- Turn off the transmit threshold mechanism (initialize the threshold
to 0). This effectively puts the chip in 'store and forward' mode
which seems to cut down on transmit errors a little. It may also
reduce transmit performace a bit, but I'm willing to do that if it
means better reliability.
- Normally, the driver allocates an mbuf cluster for each receive
descriptor. This is because we have to be prepared to accomodate up to
1500 bytes (a cluster buffer can hold up to 2K). However, using up a
whole cluster buffer for a tiny packet is a bit of a waste. Also,
it seems to me that sometimes mbufs will linger in the kernel for
a while after being passed out of the driver, which means we might
drain the mbuf cluster pool. The cluster pool is smaller than the
mbuf pool in general, so we do the following: if the packet is less
that MINCLSIZE bytes, then we copy it into a small mbuf chain and
leave the mbuf cluster in place for another go-round. This saves
mbuf clusters in some cases while still allowing them to be used
for heavy traffic exchanges with lots of full-sized frames.
- The transmit descriptor has a bit in the control word which allows
the driver to request that a 'TX OK' interrupt be generated when
a frame has been completed. Sometimes, a frame can be fragmented
across several descriptors. The manual for the real DEC 21140A says
that if this happens, the 'TX interrupt request' bit is only valid
in the descriptor of the last fragment. With the ASIX chip, it seems
the 'TX interrupt request' bit is only valid in the descriptor of
the _first_ fragment. Actually, the manual contains conflicting
information, but I think it's supposed to be the first fragment.
To play it safe, set the bit in both the first and last fragment to
be sure that we get a TX OK interrupt. Without this fix, the driver
can sometimes be late in releasing mbufs from the transmit queue
after transmission.
(<blank@fox.uni-trier.de>) about quirks being set as
arithmetic values, not as bitfields. Add HP, Kennedy
and M4 1/2" reel quirk entries.
Do a lot of gratuitous source changing.
Audit all functions that build ccbs for the tape driver
and decide whether each one can be retried or not.
Still to do is some more state management post errors.
IDE hardare. The attempted fix in rev.1.182 was a no-op except for
adding dozens of style bugs. The undocumented options ALI_V and
DISABLE_PCI_IDE go away as a side effect. ALI_V was a no-op because
rev.1.182 was a no-op. DISABLE_PCI_IDE didn't actually disable
PCI IDE. It disabled the buggy code in wdprobe() at a cost of
completely breaking support for Promise controllers.
Broken in: rev.1.139
if option CY_PCI_FASTINTR is configured and mapping the irq to a
fastintr is possible. Unfortunately, this has to be optional because
pci_map_int_right() doesn't handle the INTR_EXCL flag right --
INTR_EXCL is honoured even if the interrupt needs to be non-exclusive
for other devices to work.
buffer had to be left on the head of the queue for [bufq]disksort()
to sort against. This isn't right for devices that can support multiple
active i/o's, and only the fd driver did it. "Fixing" this in rev.1.36
of ufs_disksubr.c broke the fd driver in much the same way as rev.1.52
of <sys/buf.h> broke it (see rev.1.119).
Bug reported and fix tested by: dt
black hole device. The controller will now only accept selections if
the black hole device is present and some other target/lun is enabled
for target mode.
Handle the IGNORE WIDE RESIDUE message. This support has not been tested.
Checkpoint work on handling ABORT, BUS DEVICE RESET, TERMINATE I/O PROCESS,
and CLEAR QUEUE messages as a target.
Fix a few problems with tagged command handling in target mode.
Wait until the sync offset counter falls to 0 before changing phase
after a data-in transfer completes as the DMA logic seems to indicate
transfer complete as soon as our last REQ is issued.
Simplify some of the target mode message handling code in the sequencer.
'Black Hole' device uses this feature to schedule itself against any
target or lun attached to a controller that receives an unwanted request
from an initiator instead of having an instance per potential target/lun
request.
Use the wildcard entries to simplify wildcard async callback storage.
Don't announce devices twice to peripheral drivers. The devices will
be announced as soon as the AC_PATH_REGISTERED event is registered by
the peripheral driver, so no manaul push of this event is required.
Reviewed by: Kenneth Merry <ken@FreeBSD.org>
data and sense information for target mode devices for which no other
peripheral driver is attached. This simplifies the task of dealing with
luns that are not otherwise enabled for target mode if the controller
does not have firmware that automatically deals with this case (e.g.
the aic7xxx driver).
- Don't try to set typematic rate if there is not a keyboard.
- Fix wrong test on error code.
- Don't try to claim the keyboard twice. The second call will fail.
using the new pci_map_int_right() variant of pci_map_int(). Fast
interrupts work for PCI devices if and only if they are exclusive.
(The PCI interrupt mux doesn't support fast interrupts and can't
support a mixture of fast and slow interrupts even in principle.)
Don't assume that intrmask_t == unsigned in pci_map_int().
