HGST was bought by WDC. Over the years, it has sold different drives
branded as HGST, WD or WDC. All of them need the HGST workaround of
sending 4k-sized packets (or multiples of 4k). And the ones that don't
really need this aren't broken by this change. Submitter is the vendor
who has tested these changes on a number of drives. I've simplified it
slightly, since we don't need additional vendors for this at this
time.
Submitted by: JacobBurley via github on behalf of WDC
Pull Request: https://github.com/freebsd/freebsd/pull/391
The -l flag sends only the READ CAPACITY (16) sevice action. Normally
we send the READ CAPACITY (10) command, and only send RC16 when the
capacity is larger than 2TB (since that's the max RC10 can
report). However, some badly programmed drives report different
numbers for RC10 and RC16. This can be hard to diagnose, but generally
there's a "Logical block address out of range" error when RC16 reports
a larger number than RC10 and the RC10 number is the correct one. By
comparing the output of readcap with and without the -l argmuent, one
can determine if there's a mismatch and if the DA_Q_NO_RC16 quirk is
needed.
Reviewed by: ken@
Differential Revision: https://reviews.freebsd.org/D19536
Implement MK_NVME now that the expression for where NVMe is
complicated. Default it to "yes" for x86 and powerpc64 and
no everywhere else. Use it in camcontrol to define WITH_NVME
for those platforms where we support nvme.
This should fix the newly introduced nvme files to camcontrol
which were building everywhere.
Pointy Hat To: imp
Sponsored by: Netflix
Both ATA and NVME have an identify command. They are completely
different, but to the user they are the same. Leverage nvmecontrol's
print_controller code to provide that functionality to camcontrol
identify. Query the path to see what kind of protocol it supports, and
send the most appropriate command down. Refactor nvme_print_dev a
little to make it easy to get the nvme cdata.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D15371
Report the NVMe spec, number of lanes (and max) as well as the PCIe
generation we're negotiated at (and max) for the camcontrol rate
command.
Reviewed by: scottl (the output, not the code)
Sponsored by: Netflix
Make it possible to retrieve mmc parameters via the XPT_GET_ADVINFO
call instead. Convert camcontrol to the new scheme.
Reviewed by: imp. kibab
Sponsored by: Netflix
Differential Revision: D13868
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
No functional change intended.
ZAC (Zoned-device ATA Command set) is the standard for addressing SMR
(shingled magnetic recording) devices over SATA. Drives indicate their
support for ZAC in their IDENTIFY block. Print whether and how a drive
supports ZAC in the output of "camcontrol identify".
Reviewed by: ken, imp
MFC after: 3 weeks
Sponsored by: Spectra Logic Corp
Differential Revision: https://reviews.freebsd.org/D13171
- Delete trailing whitespace.
- Replace 8 single column spaces with hard tabs.
- Delete lines with consisting purely of blank space.
- Add space between `return` and `(`, per style(9).
Special care was taken to not blindly replace 8 single column spaces
with tabs; doing so could break tools that do strict string comparisons
with camcontrol output.
specific parameter.
Tape drives include write protect (WP), Buffered Mode and Speed
settings in the device-specific parameter. Clearing this
parameter on a mode select can have the effect of turning off
write protect or buffered mode, or changing the speed setting of
the tape drive.
Disks report DPO/FUA support via the device specific parameter
for MODE SENSE, but the bit is reserved for MODE SELECT. So we
clear this for disks (and other non-tape devices) to avoid
potential errors from the target device.
sbin/camcontrol/modeedit.c:
Clear the device-specific parameter in the mode page
header if we're not operating on a tape drive.
MFC after: 3 days
Sponsored by: Spectra Logic
name and unit number in camcontrol(8).
Previously camcontrol(8) only supported rescanning or resetting
devices specified by bus:target:lun. This is because for
rescanning at least, you don't have a peripheral name and unit
number (e.g. da4) for devices that don't exist yet.
That is still the case after this change, but in other cases, when
the device does exist in the CAM EDT (Existing Device Table), we
do a careful lookup of the bus/target/lun if the user supplies a
peripheral name and unit number to find the bus:target:lun and then
issue the requested reset or rescan.
The lookup is done without actually opening the device in question,
since a rescan is often done to make a device go away after it has
been pulled. (This is especially true for busses/controllers, like
parallel SCSI controllers, that don't automatically detect changes
in topology.) Opening a device that is no longer there to
determine the bus/target/lun might result in error recovery actions
when the user really just wanted to make the device go away.
sbin/camcontrol/camcontrol.c:
In dorescan_or_reset(), if the use hasn't specified a
numeric argument, assume he has specified a device. Lookup
the pass(4) instance for that device using the transport
layer CAMGETPASSTHRU ioctl. If that is successful, we can
use the returned bus:target:lun to rescan or reset the
device.
Under the hood, resetting a device using XPT_RESET_DEV is
actually sent via the pass(4) device anyway. But this
provides a way for the user to specify devices in a more
convenient way, and can work on device rescans when the
device is going away, assuming it still exists in the EDT.
sbin/camcontrol/camcontrol.8:
Update the man page for the rescan and reset subcommands
to reflect that you can now use a device name and unit
number with them.
Sponsored by: Spectra Logic
MFC after: 3 days
camcontrol timestamp -s would somtimes fail due to stack garbage. Zero out
the timestamp parameters to fix it.
Fix another nearby bug, and update the man page.
sbin/camcontrol/timestamp.c:
In set_timestamp(), bzero ts_p prior to creating the timestamp.
Previously stack garbage could cause some tape drives to reject the
timestamp.
In set_timestamp(), check for failures from strptime().
sbin/camcontrol/camcontrol.8:
Add the time argument to the -T option to camcontrol timestamp -s
in the long description.
Change the time/date format used in the camcontrol timestamp
example to RFC 2822 format. This fixes a time zone issue with the
original example by specifying the time zone as -0600. Otherwise,
the time zone seems to default to standard time in the current
locale, which makes the time, when reported back from the drive,
1 hour off from the intended setting. This also fixes a duplicate
day of the week ("Wednesday Wed") in the previous example.
Submitted by: Sam Klopsch
MFC after: 3 days
Sponsored by: Spectra Logic
Users can use the new generic argument, -Q task_attr, to specify a task
attribute (simple, ordered, head of queue, aca) for the commands issued.
The the default is simple, which works with all SCSI devices that support
tagged queueing.
This will mostly be useful for debugging target behavior in certain
situations.
You can try it out by compiling CTL with CTL_IO_DELAY turned on (in
sys/cam/ctl/ctl_io.h) and then do something like this with one of the CTL
LUNs:
ctladm delay 0:0 -l done -t 10
camcontrol tur da34 -v
And at then before the 10 second timer is up, in another terminal:
camcontrol inquiry da34 -Q ordered -v
The Inquiry should complete just after the TUR completes. Ordinarily
it would complete first because of the delay injection, but because the
task attribute is set to ordered in this case, CTL holds it up until the
previous command has completed.
sbin/camcontrol/camcontrol.c:
Add the new generic argument, -Q, which allows the user to specify
a SCSI task attribute. The user can specify task attributes by
name or numerically.
Add a new task_attr arguments to SCSI sub-functions.
sbin/camcontrol/attrib.c,
sbin/camcontrol/camcontrol.h,
sbin/camcontrol/fwdownload.c,
sbin/camcontrol/modeedit.c,
sbin/camcontrol/persist.c,
sbin/camcontrol/timestamp.c,
sbin/camcontrol/zone.c:
Add the new task_attr argument to SCSI sub-functions.
sbin/camcontrol/camcontrol.8:
Document the new -Q option, and add an example.
Sponsored by: Spectra Logic
MFC after: 1 week
CID 1229913 Fix output of "camcontrol persist -i report_capabilities".
The reported Persistent Reservation Types were wrong in all
cases.
CID 1356029 Annotate the code so Coverity will know that this is a false
positive.
CID 1366830 Fix a memory leak in "camcontrol timestamp -s"
CID 1366832 Fix a segfault that could be caused by bad drive firmware
Also, fix the man page entry for the "camcontrol epc state" command to match
what the code does.
Reviewed by: ken, wblock
MFC after: 4 weeks
Sponsored by: Spectra Logic Corp
Differential Revision: https://reviews.freebsd.org/D9239
Replace archaic "busses" with modern form "buses."
Intentionally excluded:
* Old/random drivers I didn't recognize
* Old hardware in general
* Use of "busses" in code as identifiers
No functional change.
http://grammarist.com/spelling/buses-busses/
PR: 216099
Reported by: bltsrc at mail.ru
Sponsored by: Dell EMC Isilon
Previously code ignored resid field and returned extra zeroes in case of
data underflow. Now it returns only real bytes received from target.
MFC after: 2 weeks
If our buffer is too small, we may receive part of the page, and should
not try read/write past the end of the buffer.
Reported by: Coverity
CID: 1368374, 1368375
MFC after: 1 week
This adds support to camcontrol(8) and libcam(3) for getting and setting
the time on SCSI protocol drives. This is more commonly found on tape
drives, but is a SPC (SCSI Primary Commands) command, and may be found
on any device that speaks SCSI.
The new camcontrol timestamp subcommand allows getting the current device
time or setting the time to the current system time or any arbitrary time.
sbin/camcontrol/Makefile:
Add timestamp.c.
sbin/camcontrol/camcontrol.8:
Document the new timestamp subcommand.
sbin/camcontrol/camcontrol.c:
Add the timestamp subcommand to camcontrol.
sbin/camcontrol/camcontrol.h:
Add the timestamp() function prototype.
sbin/camcontrol/timestamp.c:
Timestamp setting and reporting functionality.
sys/cam/scsi/scsi_all.c:
Add two new CCB building functions, scsi_set_timestamp() and
scsi_report_timestamp(). Also, add a new helper function,
scsi_create_timestamp().
sys/cam/scsi/scsi_all.h:
Add CDB and parameter data for the the set and report timestamp
commands.
Add function declarations for the new CCB building and helper
functions.
Submitted by: Sam Klopsch
Sponsored by: Spectra Logic
MFC After: 2 weeks
In r307684, I changed rescan_or_reset_bus() to bzero stack-allocated CCBs
before sending them to the kernel because there was stack garbage in there
that wound up meaning that bogus CCB flags were set.
While this fixed the 'camcontrol rescan all' case (XPT_DEV_MATCH CCBs were
failing previously), it broke the 'camcontrol rescan 0' (or any other
number) case when INVARIANTS are turned on. Rescanning a single bus
reliably produced an assert in cam_periph_runccb():
panic: cam_periph_runccb: ccb=0xfffff80044ffe000, func_code=0x708, flags=0xffffdde0
The flags values don't make sense from the code. Changing the CCBs in
rescan_or_reset_bus() from stack to heap allocated avoids the problem.
It would be better to understand why userland stack allocated CCBs don't
work properly, since there may be other code that breaks if stack allocated
CCBs don't work.
sbin/camcontrol/camcontrol.c:
In rescan_or_reset_bus(), allocate the CCBs using malloc(3) instead
of on the stack to avoid an assertion in cam_periph_runccb().
MFC after: 3 days
Sponsored by: Spectra Logic
the header. Otherwise stack garbage can lead to random flags getting set.
This showed up as 'camcontrol rescan all' failing with EINVAL because the
address type wasn't CAM_DATA_VADDR.
sbin/camcontrol/camcontrol.c:
In rescan_or_reset_bus(), bzero the stack-allocated CCBs before
use instead of clearing the body.
MFC after: 3 days
Sponsored by: Spectra Logic
defects. When shifting an unsigned byte into the upper 8 bits of
an int and the resulting value is greater than 0x7FFFFFF, the result
will be sign extended when converting to a 64 bit unsigned long.
Fix by casting to (uint64_t) before the shift.
Reported by: Coverity
CID: 1356044, 1356045
Reviewed by: ken
overflow defect. Use the new CCB_CLEAR_ALL_EXCEPT_HDR() macro
instead of the calling bzero() on the pointer to the header used
as an array and indexed by 1.
Don't leak a buffer after executing "goto restart_report" by
overwriting its pointer with the results of another calloc().
Be sure to clear the buffer before reusing it. (CID 1356042)
Reported by: Coverity
CID: 1356022, 1356034, 1356023, 1356035, 1356042
Reviewed by: ken
The currently used idiom for clearing the part of a ccb after its
header generates one or two Coverity errors for each time it is
used. All instances generate an Out-of-bounds access (ARRAY_VS_SINGLETON)
error because of the treatment of the header as a two element array,
with a pointer to the non-existent second element being passed as
the starting address to bzero(). Some instances also alsp generate
Out-of-bounds access (OVERRUN) errors, probably because the space
being cleared is larger than the sizeofstruct ccb_hdr).
In addition, this idiom is difficult for humans to understand and
it is error prone. The user has to chose the proper struct ccb_*
type (which does not appear in the surrounding code) for the sizeof()
in the length calculation. I found several instances where the
length was incorrect, which could cause either an actual out of
bounds write, or incompletely clear the ccb.
A better way is to write the code to clear the ccb itself starting
at sizeof(ccb_hdr) bytes from the start of the ccb, and calculate
the length based on the specific type of struct ccb_* being cleared
as specified by the union ccb member being used. The latter can
normally be seen in the nearby code. This is friendlier for Coverity
and other static analysis tools because they will see that the
intent is to clear the trailing part of the ccb.
Wrap all of the boilerplate code in a convenient macro that only
requires a pointer to the desired union ccb member (or a pointer
to the union ccb itself) as an argument.
Reported by: Coverity
CID: 1007578, 1008684, 1009724, 1009773, 1011304, 1011306
CID: 1011307, 1011308, 1011309, 1011310, 1011311, 1011312
CID: 1011313, 1011314, 1011315, 1011316, 1011317, 1011318
CID: 1011319, 1011320, 1011321, 1011322, 1011324, 1011325
CID: 1011326, 1011327, 1011328, 1011329, 1011330, 1011374
CID: 1011390, 1011391, 1011392, 1011393, 1011394, 1011395
CID: 1011396, 1011397, 1011398, 1011399, 1011400, 1011401
CID: 1011402, 1011403, 1011404, 1011405, 1011406, 1011408
CID: 1011409, 1011410, 1011411, 1011412, 1011413, 1011414
CID: 1017461, 1018387, 1086860, 1086874, 1194257, 1229897
CID: 1229968, 1306229, 1306234, 1331282, 1331283, 1331294
CID: 1331295, 1331535, 1331536, 1331539, 1331540, 1341623
CID: 1341624, 1341637, 1341638, 1355264, 1355324
Reviewed by: scottl, ken, delphij, imp
MFH: 1 month
Differential Revision: https://reviews.freebsd.org/D6496
This change includes support for SCSI SMR drives (which conform to the
Zoned Block Commands or ZBC spec) and ATA SMR drives (which conform to
the Zoned ATA Command Set or ZAC spec) behind SAS expanders.
This includes full management support through the GEOM BIO interface, and
through a new userland utility, zonectl(8), and through camcontrol(8).
This is now ready for filesystems to use to detect and manage zoned drives.
(There is no work in progress that I know of to use this for ZFS or UFS, if
anyone is interested, let me know and I may have some suggestions.)
Also, improve ATA command passthrough and dispatch support, both via ATA
and ATA passthrough over SCSI.
Also, add support to camcontrol(8) for the ATA Extended Power Conditions
feature set. You can now manage ATA device power states, and set various
idle time thresholds for a drive to enter lower power states.
Note that this change cannot be MFCed in full, because it depends on
changes to the struct bio API that break compatilibity. In order to
avoid breaking the stable API, only changes that don't touch or depend on
the struct bio changes can be merged. For example, the camcontrol(8)
changes don't depend on the new bio API, but zonectl(8) and the probe
changes to the da(4) and ada(4) drivers do depend on it.
Also note that the SMR changes have not yet been tested with an actual
SCSI ZBC device, or a SCSI to ATA translation layer (SAT) that supports
ZBC to ZAC translation. I have not yet gotten a suitable drive or SAT
layer, so any testing help would be appreciated. These changes have been
tested with Seagate Host Aware SATA drives attached to both SAS and SATA
controllers. Also, I do not have any SATA Host Managed devices, and I
suspect that it may take additional (hopefully minor) changes to support
them.
Thanks to Seagate for supplying the test hardware and answering questions.
sbin/camcontrol/Makefile:
Add epc.c and zone.c.
sbin/camcontrol/camcontrol.8:
Document the zone and epc subcommands.
sbin/camcontrol/camcontrol.c:
Add the zone and epc subcommands.
Add auxiliary register support to build_ata_cmd(). Make sure to
set the CAM_ATAIO_NEEDRESULT, CAM_ATAIO_DMA, and CAM_ATAIO_FPDMA
flags as appropriate for ATA commands.
Add a new get_ata_status() function to parse ATA result from SCSI
sense descriptors (for ATA passthrough over SCSI) and ATA I/O
requests.
sbin/camcontrol/camcontrol.h:
Update the build_ata_cmd() prototype
Add get_ata_status(), zone(), and epc().
sbin/camcontrol/epc.c:
Support for ATA Extended Power Conditions features. This includes
support for all features documented in the ACS-4 Revision 12
specification from t13.org (dated February 18, 2016).
The EPC feature set allows putting a drive into a power power mode
immediately, or setting timeouts so that the drive will
automatically enter progressively lower power states after various
idle times.
sbin/camcontrol/fwdownload.c:
Update the firmware download code for the new build_ata_cmd()
arguments.
sbin/camcontrol/zone.c:
Implement support for Shingled Magnetic Recording (SMR) drives
via SCSI Zoned Block Commands (ZBC) and ATA Zoned Device ATA
Command Set (ZAC).
These specs were developed in concert, and are functionally
identical. The primary differences are due to SCSI and ATA
differences. (SCSI is big endian, ATA is little endian, for
example.)
This includes support for all commands defined in the ZBC and
ZAC specs.
sys/cam/ata/ata_all.c:
Decode a number of additional ATA command names in ata_op_string().
Add a new CCB building function, ata_read_log().
Add ata_zac_mgmt_in() and ata_zac_mgmt_out() CCB building
functions. These support both DMA and NCQ encapsulation.
sys/cam/ata/ata_all.h:
Add prototypes for ata_read_log(), ata_zac_mgmt_out(), and
ata_zac_mgmt_in().
sys/cam/ata/ata_da.c:
Revamp the ada(4) driver to support zoned devices.
Add four new probe states to gather information needed for zone
support.
Add a new adasetflags() function to avoid duplication of large
blocks of flag setting between the async handler and register
functions.
Add new sysctl variables that describe zone support and paramters.
Add support for the new BIO_ZONE bio, and all of its subcommands:
DISK_ZONE_OPEN, DISK_ZONE_CLOSE, DISK_ZONE_FINISH, DISK_ZONE_RWP,
DISK_ZONE_REPORT_ZONES, and DISK_ZONE_GET_PARAMS.
sys/cam/scsi/scsi_all.c:
Add command descriptions for the ZBC IN/OUT commands.
Add descriptions for ZBC Host Managed devices.
Add a new function, scsi_ata_pass() to do ATA passthrough over
SCSI. This will eventually replace scsi_ata_pass_16() -- it
can create the 12, 16, and 32-byte variants of the ATA
PASS-THROUGH command, and supports setting all of the
registers defined as of SAT-4, Revision 5 (March 11, 2016).
Change scsi_ata_identify() to use scsi_ata_pass() instead of
scsi_ata_pass_16().
Add a new scsi_ata_read_log() function to facilitate reading
ATA logs via SCSI.
sys/cam/scsi/scsi_all.h:
Add the new ATA PASS-THROUGH(32) command CDB. Add extended and
variable CDB opcodes.
Add Zoned Block Device Characteristics VPD page.
Add ATA Return SCSI sense descriptor.
Add prototypes for scsi_ata_read_log() and scsi_ata_pass().
sys/cam/scsi/scsi_da.c:
Revamp the da(4) driver to support zoned devices.
Add five new probe states, four of which are needed for ATA
devices.
Add five new sysctl variables that describe zone support and
parameters.
The da(4) driver supports SCSI ZBC devices, as well as ATA ZAC
devices when they are attached via a SCSI to ATA Translation (SAT)
layer. Since ZBC -> ZAC translation is a new feature in the T10
SAT-4 spec, most SATA drives will be supported via ATA commands
sent via the SCSI ATA PASS-THROUGH command. The da(4) driver will
prefer the ZBC interface, if it is available, for performance
reasons, but will use the ATA PASS-THROUGH interface to the ZAC
command set if the SAT layer doesn't support translation yet.
As I mentioned above, ZBC command support is untested.
Add support for the new BIO_ZONE bio, and all of its subcommands:
DISK_ZONE_OPEN, DISK_ZONE_CLOSE, DISK_ZONE_FINISH, DISK_ZONE_RWP,
DISK_ZONE_REPORT_ZONES, and DISK_ZONE_GET_PARAMS.
Add scsi_zbc_in() and scsi_zbc_out() CCB building functions.
Add scsi_ata_zac_mgmt_out() and scsi_ata_zac_mgmt_in() CCB/CDB
building functions. Note that these have return values, unlike
almost all other CCB building functions in CAM. The reason is
that they can fail, depending upon the particular combination
of input parameters. The primary failure case is if the user
wants NCQ, but fails to specify additional CDB storage. NCQ
requires using the 32-byte version of the SCSI ATA PASS-THROUGH
command, and the current CAM CDB size is 16 bytes.
sys/cam/scsi/scsi_da.h:
Add ZBC IN and ZBC OUT CDBs and opcodes.
Add SCSI Report Zones data structures.
Add scsi_zbc_in(), scsi_zbc_out(), scsi_ata_zac_mgmt_out(), and
scsi_ata_zac_mgmt_in() prototypes.
sys/dev/ahci/ahci.c:
Fix SEND / RECEIVE FPDMA QUEUED in the ahci(4) driver.
ahci_setup_fis() previously set the top bits of the sector count
register in the FIS to 0 for FPDMA commands. This is okay for
read and write, because the PRIO field is in the only thing in
those bits, and we don't implement that further up the stack.
But, for SEND and RECEIVE FPDMA QUEUED, the subcommand is in that
byte, so it needs to be transmitted to the drive.
In ahci_setup_fis(), always set the the top 8 bits of the
sector count register. We need it in both the standard
and NCQ / FPDMA cases.
sys/geom/eli/g_eli.c:
Pass BIO_ZONE commands through the GELI class.
sys/geom/geom.h:
Add g_io_zonecmd() prototype.
sys/geom/geom_dev.c:
Add new DIOCZONECMD ioctl, which allows sending zone commands to
disks.
sys/geom/geom_disk.c:
Add support for BIO_ZONE commands.
sys/geom/geom_disk.h:
Add a new flag, DISKFLAG_CANZONE, that indicates that a given
GEOM disk client can handle BIO_ZONE commands.
sys/geom/geom_io.c:
Add a new function, g_io_zonecmd(), that handles execution of
BIO_ZONE commands.
Add permissions check for BIO_ZONE commands.
Add command decoding for BIO_ZONE commands.
sys/geom/geom_subr.c:
Add DDB command decoding for BIO_ZONE commands.
sys/kern/subr_devstat.c:
Record statistics for REPORT ZONES commands. Note that the
number of bytes transferred for REPORT ZONES won't quite match
what is received from the harware. This is because we're
necessarily counting bytes coming from the da(4) / ada(4) drivers,
which are using the disk_zone.h interface to communicate up
the stack. The structure sizes it uses are slightly different
than the SCSI and ATA structure sizes.
sys/sys/ata.h:
Add many bit and structure definitions for ZAC, NCQ, and EPC
command support.
sys/sys/bio.h:
Convert the bio_cmd field to a straight enumeration. This will
yield more space for additional commands in the future. After
change r297955 and other related changes, this is now possible.
Converting to an enumeration will also prevent use as a bitmask
in the future.
sys/sys/disk.h:
Define the DIOCZONECMD ioctl.
sys/sys/disk_zone.h:
Add a new API for managing zoned disks. This is very close to
the SCSI ZBC and ATA ZAC standards, but uses integers in native
byte order instead of big endian (SCSI) or little endian (ATA)
byte arrays.
This is intended to offer to the complete feature set of the ZBC
and ZAC disk management without requiring the application developer
to include SCSI or ATA headers. We also use one set of headers
for ioctl consumers and kernel bio-level consumers.
sys/sys/param.h:
Bump __FreeBSD_version for sys/bio.h command changes, and inclusion
of SMR support.
usr.sbin/Makefile:
Add the zonectl utility.
usr.sbin/diskinfo/diskinfo.c
Add disk zoning capability to the 'diskinfo -v' output.
usr.sbin/zonectl/Makefile:
Add zonectl makefile.
usr.sbin/zonectl/zonectl.8
zonectl(8) man page.
usr.sbin/zonectl/zonectl.c
The zonectl(8) utility. This allows managing SCSI or ATA zoned
disks via the disk_zone.h API. You can report zones, reset write
pointers, get parameters, etc.
Sponsored by: Spectra Logic
Differential Revision: https://reviews.freebsd.org/D6147
Reviewed by: wblock (documentation)
This makes it possible to manually force updating capacity data
after the disk got resized. Without it it might be neccessary to
reboot before FreeBSD notices updated disk size under eg VMWare.
Discussed with: imp@
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D6108
It was already done 4 lines prior and the value of error didn't change
MFC after: 3 days
Reported by: Coverity
CID: 1011236
Sponsored by: EMC / Isilon Storage Division
