o move tx taps from ath_start to ath_tx_start so lots more
state is available to tap
o add tx flags
o add tx rate
o add tx power (constant for the moment)
o add tx antenna state
a new bpf_mtap2 routine that does the right thing for an mbuf
and a variable-length chunk of data that should be prepended.
o while we're sweeping the drivers, use u_int32_t uniformly when
when prepending the address family (several places were assuming
sizeof(int) was 4)
o return M_ASSERTVALID to BPF_MTAP* now that all stack-allocated
mbufs have been eliminated; this may better be moved to the bpf
routines
Reviewed by: arch@ and several others
o fix race condition when processing rx descriptors: because we use
a self-linked descriptor at the end of the rx descriptor list to
avoid rx overruns (which can easily happen for 5212 parts that enable
PHY errors) we must carefully check that a descriptor is "done" by
looking ahead to the next descriptor before believing the done bit
in the current descriptor (this is all handled in the HAL since the
rx descriptor format is chip-specific so we need to pass in two
additional parameters--the physical address of the current descriptor
and the virtual address of the next descriptor in the list)
o check copyout return status for SIOCGATHSTATS ioctl
Approved by: re (scottl)
this problem put these lines back in. While they should be
unnecessary, they appear to be sometimes necessary.
Reviewed in concept: dfr
Approved by: re (scottl@)
5212-based devices because PHY errors are used to collect data
on environmental noise that and doesn't truly reflect the state
of the communications media. The result is confused users.
Folks that want to watch PHY errors can still get the statistics
through the device ioctl (used by athstats).
to the pci attachment. Cardbus is a derived class of pci so all pci
drivers are automatically available for matching against cardbus devices.
Reviewed by: imp
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
seeded with arc4random rather than calling arc4random for each
packet. Note this is the same algorithm used to select the IV when
doing WEP on the host.
o don't grab the mutex at the top of ath_detach; it does nothing
useful
o deal with entry to ath_ioctl during detach to disable promiscuous
mode as a result of calling bpfdetach2: cannot call ath_init when
the device is marked invalid as the code isn't prepared to deal
with it (in particular by that time the hal reference may have
been yanked)
change ath_rate_ctl_reset to handle transition from station
mode to adhoc mode; was not resetting the initial xmit rate
causing outbound frames to be dicarded
calculate smoothed signal quality data for each node.
o add a 16-deep history buffer to each driver-private node storage that
holds rssi and antenna info for received frames
o override the default per-node "get rssi" method to return an average
rssi value based on samples collected over the last second
o enable beacon reception so even idle systems maintain a running history
of signal quality
This data may also be useful for improving the rate control algorithm.
Based on work by Tom Marshall <tommy@home.tig-grr.com> for MADWIFI.
to the 802.11 layer if they are at least IEEE80211_MIN_LEN
o mask off interrupt status bits that we don't care about so we don't do
the wrong thing; this fixes a problem where the beacon miss interrupt status
bit is delivered together with other status bits when operating in monitor
mode (we would post a beacon miss swi and then do the wrong thing)
safe since the 802.11 layer does the right thing for 11a operation)
o select short preamble operation based on the negotiated capabilities; not
just the local state/capability
o fillin the duration field in the 802.11 header as appropriate
o remove detection of 11g support; no longer needed
Obtained from: MADWIFI (with modifications)
count handling of station entries in hostap mode:
Input path:
o driver is now expected to find the node associated with the
sender of a received frame; use ic_bss if none is located
o driver passes the (referenced) node into ieee80211_input for
use within the wlan module and is responsible for cleaning up
on return
o the antenna state is no longer passed up with each frame; this
is now considered driver-private state and drivers are responsible
for keeping it in the driver-private part of a node
Output path:
Revamp output path for management frames to eliminate redundant
locking that causes problems and to correct reference counting
bogosity that occurs when stations are timed out due to inactivity
(in AP mode). On output the refcnt'd node is stashed in the pkthdr's
recvif field (yech) and retrieved by the driver. This eliminates
an unref/ref scenario and related node table unlock/lock due to the
driver looking up the node. This is particularly important when
stations are timed out as this causes a lock order reversal that
can result in a deadlock. As a byproduct we also reduce the overhead
for sending management frames (minimal). Additional fallout from
this is a change to ieee80211_encap to return a refcn't node for
tieing to the outbound frame. Node refcnts are not reclaimed until
after a frame is completely processed (e.g. in the tx interrupt
handler). This is especially important for timed out stations as
this deref will be the final one causing the node entry to be
reclaimed.
Additional semi-related changes:
o replace m_copym use with m_copypacket (optimization)
o add assert to verify ic_bss is never free'd during normal operation
o add comments explaining calling conventions by drivers for frames
going in each direction
o remove extraneous code that "cannot be executed" (e.g. because
pointers may never be null)
quietly discard them; this just permits them to be collected with bpf)
o add a counter for the number of rate control frames discarded when not in
monitor mode
o move the rx "too short" statistic in the stat structure so non-error rx stats
are together (NB: ABI change to apps that collect stats via driver ioctl)
mistakes (this mistake was not an issue because the length is only used to
decide whether or not to allocate a cluster)
o while here, move a beacon length comment to the "right place"
