Before this change, the current code handles SIOCGIFADDR the same
way with SIOCSIFADDR, which involves full arp_ifinit, et al. They
should be unnecessary for SIOCGIFADDR case.
Differential Revision: https://reviews.freebsd.org/D1508
Reviewed by: glebius
MFC after: 2 weeks
Instead of reusing the same reg parsing code, create one, common function
that puts reg contents to the resource list. Address cells and size cells
are passed rather than acquired here so that any bus can have different
default values.
Obtained from: Semihalf
Reviewed by: andrew, ian, nwhitehorn
Sponsored by: The FreeBSD Foundation
driver name and NIC driver softc via the device(9) tree,
instead of going dirty through the ifnet(9) layer.
Differential Revision: D1506
Reviewed by: imp, jhb
if_ixl to version 1.3.0, if_ixlv to version 1.2.0
- Major change in both drivers is to add RSS support
- In ixl fix some interface speed related issues, dual
speed was not changing correctly, KR/X media was not
displaying correctly (this has a workaround until a
more robust media handling is in place)
- Add a warning when using Dell NPAR and the speed is
less than 10G
- Wrap a queue hung message in IXL_DEBUG, as it is non-fatal,
and without tuning can display excessively
MFC after: 1 week
unnecessary filter configuration code in nge_init_locked().
While I'm here add a check for driver running state for multicast
filter handling. Also remove unnecessary assignment to error
variable since it is cleared in the function entry.
Suggested by: brad@OpenBSD.org
devices which don't support the synchronize cache SCSI command are
likely to also not support the prevent-allow medium removal SCSI
command.
PR: 185747
MFC after: 1 week
moving the handling of curcmd->error != 0 to the end of the interrupt
handler. Also make sdhci_finish_data() idempotent by moving the setting
of slot->data_done = 1 down past the point where the busdma buffer is
unmapped. This allows for the possibility that the finish routine can
get called from multiple places when handling errors.
Poll for link state when the link is down, even for interrupt capable
PHYs.
Allow PHYs to report a dubious "partial" link. If this state is seen 3
consecutive times (each check is ~1s apart) then reset the PHY. This is
a workaround for a situation where repeatedly toggling the link from the
peer gets the AEL2005 PHY into a state where it never establishes a PCS
block lock even when everything is in order.
MFC after: 1 week
and not automatically come back if they were gone for a short
period of time.
The isp(4) driver has a 30 second gone device timer that gets
activated whenever a device goes away. If the device comes back
before the timer expires, we don't send a notification to CAM that
it has gone away. If, however, there is a command sent to the
device while it is gone and before it comes back, the isp(4) driver
sends the command back with CAM_SEL_TIMEOUT status.
CAM responds to the CAM_SEL_TIMEOUT status by removing the device.
In the case where a device comes back within the 30 second gone
device timer window, though, we weren't telling CAM the device
came back.
So, fix this by tracking whether we have told CAM the device is
gone, and if we have, send a rescan if it comes back within the 30
second window.
ispvar.h:
In the fcportdb_t structure, add a new bitfield,
reported_gone. This gets set whenever we return a command
with CAM_SEL_TIMEOUT status on a Fibre Channel device.
isp_freebsd.c:
In isp_done(), if we're sending CAM_SEL_TIMEOUT for for a
command sent to a FC device, set the reported_gone bit.
In isp_async(), in the ISPASYNC_DEV_STAYED case, rescan the
device in question if it is mapped to a target ID and has
been reported gone.
In isp_make_here(), take a port database entry argument,
and clear the reported_gone bit when we send a rescan to
CAM.
In isp_make_gone(), take a port database entry as an
argument, and set the reported_gone bit when we send an
async event telling CAM consumers that the device is gone.
Sponsored by: Spectra Logic
MFC after: 1 week
The Command Reference Number is used for precise delivery of
commands, and is part of the FC-Tape functionality set. (This is
only enabled for devices that support precise delivery of commands.)
It is an 8-bit unsigned number that increments from 1 to 255. The
commands sent by the initiator must be processed by the target in
CRN order if the CRN is non-zero.
There are certain scenarios where the Command Reference Number
sequence needs to be reset. When the target is power cycled, for
instance, the initiator needs to reset the CRN to 1. The initiator
will know this because it will see a LIP (when directly connected)
or get a logout/login event (when connected to a switch).
The isp(4) driver was not resetting the CRN when a target
went away and came back. When it saw the target again after a
power cycle, it would continue the CRN sequence where it left off.
The target would ignore the command because the CRN sequence is
supposed to be reset to 1 after a power cycle or other similar
event.
The symptom that the user would see is that there would be lots of
aborted INQUIRY commands after a tape library was power cycled, and
the library would fail to probe. The INQUIRY commands were being
ignored by the tape drive due to the CRN issue mentioned above.
isp_freebsd.c:
Add a new function, isp_fcp_reset_crn(). This will reset
all of the CRNs for a given port, or the CRNs for all LUNs
on a target.
Reset the CRNs for all targets on a port when we get a LIP,
loop reset, or loop down event.
Reset the CRN for a particular target when it arrives, is changed
or departs. This is less precise behavior than the
clearing behavior specified in the FCP-4 spec (which says
that it should be reset for PRLI, PRLO, PLOGI and LOGO),
but this is the level of information we have here. If this
is insufficient, then we will need to add more precise
notification from the lower level isp(4) code.
isp_freebsd.h:
Add a prototype for isp_fcp_reset_crn().
Sponsored by: Spectra Logic
MFC after: 1 week
socket-buffer implementations, introduce a return value for MCLGET()
(and m_cljget() that underlies it) to allow the caller to avoid testing
M_EXT itself. Update all callers to use the return value.
With this change, very few network device drivers remain aware of
M_EXT; the primary exceptions lie in mbuf-chain pretty printers for
debugging, and in a few cases, custom mbuf and cluster allocation
implementations.
NB: This is a difficult-to-test change as it touches many drivers for
which I don't have physical devices. Instead we've gone for intensive
review, but further post-commit review would definitely be appreciated
to spot errors where changes could not easily be made mechanically,
but were largely mechanical in nature.
Differential Revision: https://reviews.freebsd.org/D1440
Reviewed by: adrian, bz, gnn
Sponsored by: EMC / Isilon Storage Division
may also halt in C2 and not just C3 (it seems that in some cases the BIOS
advertises its C3 state as a C2 state in _CST). Just play it safe and
disable both C2 and C3 states if a user forces the use of the TSC as the
timecounter on such CPUs.
PR: 192316
Differential Revision: https://reviews.freebsd.org/D1441
No objection from: jkim
MFC after: 1 week
the knowledge of mbuf layout, and in particular constants such as M_EXT,
MLEN, MHLEN, and so on, in mbuf consumers by unifying various alignment
utility functions (M_ALIGN(), MH_ALIGN(), MEXT_ALIGN() in a single
M_ALIGN() macro, implemented by a now-inlined m_align() function:
- Move m_align() from uipc_mbuf.c to mbuf.h; mark as __inline.
- Reimplement M_ALIGN(), MH_ALIGN(), and MEXT_ALIGN() using m_align().
- Update consumers around the tree to simply use M_ALIGN().
This change eliminates a number of cases where mbuf consumers must be aware
of whether or not mbufs returned by the allocator use external storage, but
also assumptions about the size of the returned mbuf. This will make it
easier to introduce changes in how we use external storage, as well as
features such as variable-size mbufs.
Differential Revision: https://reviews.freebsd.org/D1436
Reviewed by: glebius, trasz, gnn, bz
Sponsored by: EMC / Isilon Storage Division
into mbuf storage, to reduce knowledge about mbuf/cluster layout in the
cxgb device driver.
Reviewed by: np
Sponsored by: EMC / Isilon Storage Division
which prevents us from doing a "callout_drain()" call. The callout in
question has a lock associated with it and we are not freeing the
callout. That means we can use the "callout_stop()" function to
atomically stop the callback iff the "callout_stop()" function is
called locked. This patch applies proper locking to "callout_stop()"
and replaces a "callout_drain()" with a "callout_stop()".
MFC after: 1 week
roughly 10 years, and the driver has not enjoyed any significant maintenance
since long before that. Despite well-meaning efforts from a number of
people, myself included, it never made the jump to 64-bit and was relegated
to the back-corners of i386. Now its frailty is hampering forward progress
with Clang. Any renewed engineering efforts are of course welcome and can
happen outside of the tree. No MFC of this is planned.
but not always, identical. In particular, the path entry may contain a
unit address that the name does not. If the FDT node does have an explicit
name property, treat that as an override of the FDT path rather than
ignoring it.
MFC after: 2 weeks
