add a FreeBSD_version check. It should work fine for compiling
on -HEAD, 9.x and 8.x.
* Conditionally compile the 11n options only when 11n is enabled.
The above changes allow the ath(4) driver to compile and run on
8.1-RELEASE (Hi old PC-BSD!) but with the 11n stuff disabled.
I've done a test against the net80211 and tools in 8.1-RELEASE.
The NIC used in testing is the AR2427 in an EEEPC.
Just to be clear - this change is to allow the -HEAD ath/hal/rate
code to run on 9.x _and_ 8.x with no source changes. However,
when running on earlier kernels, it should only be used for legacy
mode. (Don't define ATH_ENABLE_11N.)
damage which I committed when I had less clue about such things.
Don't ever put normal data frames on the mcast software queue.
Just put mcast frames there if needed.
Pass the txq decision into ath_tx_normal_setup(), as we've already made
the decision. Don't re-do it.
Whilst i'm here, add another random debugging statement.
This fixes bootp on if_smc, as bootp code perform SIOCSIFADDR
ioctl call immediately after sending the request (which causes
if_init being called) which causes the adapter to drop all the
packets received in the meantime.
call these after rate control selection is done.
The duration/protection code wasn't working - it expected the rix to
be valid. Unfortunately after I moved the rate control selection into
late in the process, the rix value isn't valid and thus the protection/
duration code would get things wrong.
HT frames are now correctly protected with an RTS and for the AR5416,
this involves having the aggregate frames be limited to 8K.
TODO:
* Fix up the DMA sync to occur just before the frame is queued to the
hardware. I'm adjusting the duration here but not doing the DMA
flush.
* Doubly/triply ensure that the aggregate frames are being limited to
the correct size, or the AR5416 will get unhappy when TXing RTS-protected
aggregates.
if any subframes in an aggregate have different protection from the
first frame in the formed aggregate, don't add that frame to the
aggregate.
This is likely a suboptimal method (I think we'll mostly be OK marking
frames that have seqno's with the same protection as normal data frames)
but I'll just be cautious for now.
This will be used by some upcoming code to ensure that aggregates
are enforced to be a certain size. The AR5416 has a limitation on
RTS protected aggregates (8KiB).
A BAR frame must be transmitted when an frame in an A-MPDU session fails
to transmit - it's retried too often, or it can't be cloned for
re-transmission. The BAR frame tells the remote side to advance the
left edge of the block-ack window (BAW) to a new value.
In order to do this:
* TX for that particular node/TID must be paused;
* The existing frames in the hardware queue needs to be completed, whether
they're TXed successfully or otherwise;
* The new left edge of the BAW is then communicated to the remote side
via a BAR frame;
* Once the BAR frame has been sucessfully TXed, aggregation can resume;
* If the BAR frame can't be successfully TXed, the aggregation session
is torn down.
This is a first pass that implements the above. What needs to be done/
tested:
* What happens during say, a channel reset / stuck beacon _and_ BAR
TX. It _should_ be correctly buffered and retried once the
reset has completed. But if a bgscan occurs (and they shouldn't,
grr) the BAR frame will be forcibly failed and the aggregation session
will be torn down.
Yes, another reason to disable bgscan until I've figured this out.
* There's way too much locking going on here. I'm going to do a couple
of further passes of sanitising and refactoring so the (re) locking
isn't so heavy. Right now I'm going for correctness, not speed.
* The BAR TX can fail if the hardware TX queue is full. Since there's
no "free" space kept for management frames, a full TX queue (from eg
an iperf test) can race with your ability to allocate ath_buf/mbufs
and cause issues. I'll knock this on the head with a subsequent
commit.
* I need to do some _much_ more thorough testing in hostap mode to ensure
that many concurrent traffic streams to different end nodes are correctly
handled. I'll find and squish whichever bugs show up here.
But, this is an important step to being able to flip on 802.11n by default.
The last issue (besides bug fixes, of course) is HT frame protection and
I'll address that in a subsequent commit.
Linux ath9k doesn't have this issue as it doesn't try queuing multi-
descriptor frames to the hardware.
Before, I was only setting the first and last descriptor in the final
frame correctly - and that was done by accident. The first descriptor in
the last sub-frame was being correctly updated by ath_tx_setds_11n();
the last descriptor in the last sub-frame was being correctly updated
by ath_buf_set_rate(). But both of those are "incorrect".
The correct behaviour is:
* AR_IsAggr is set for all descriptors for all subframes in an aggregate.
* AR_MoreAggr is set for all descriptors for all non-final sub-frames
in an aggregate.
Ie, all descriptors in the last sub-frame of an aggregate must have this
field set to 0.
I still need to do a couple of extra passes to ensure the pad delimiter
field is being correctly handled in all descriptors in the last sub-frame.
can be upgraded to MegaRAID mode, in which case mfi(4) should attach to
these based on the sub-vendor and -device ID instead (not currently done).
Therefore, let mpt_pci_probe() return BUS_PROBE_LOW_PRIORITY.
While it, let mpt_pci_probe() return BUS_PROBE_DEFAULT instead of 0 in
the default case.
MFC after: 3 days
First cut of new HW support from LSI and merge into FreeBSD.
Supports Drake Skinny and ThunderBolt cards.
MFhead_mfi r227574
Style
MFhead_mfi r227579
Use bus_addr_t instead of uintXX_t.
MFhead_mfi r227580
MSI support
MFhead_mfi r227612
More bus_addr_t and remove "#ifdef __amd64__".
MFhead_mfi r227905
Improved timeout support from Scott.
MFhead_mfi r228108
Make file.
MFhead_mfi r228208
Fixed botched merge of Skinny support and enhanced handling
in call back routine.
MFhead_mfi r228279
Remove superfluous !TAILQ_EMPTY() checks before TAILQ_FOREACH().
MFhead_mfi r228310
Move mfi_decode_evt() to taskqueue.
MFhead_mfi r228320
Implement MFI_DEBUG for 64bit S/G lists.
MFhead_mfi r231988
Restore structure layout by reverting the array header to
use [0] instead of [1].
MFhead_mfi r232412
Put wildcard pattern later in the match table.
MFhead_mfi r232413
Use lower case for hexadecimal numbers to match surrounding
style.
MFhead_mfi r232414
Add more Thunderbolt variants.
MFhead_mfi r232888
Don't act on events prior to boot or when shutting down.
Add hw.mfi.detect_jbod_change to enable or disable acting
on JBOD type of disks being added on insert and removed on
removing. Switch hw.mfi.msi to 1 by default since it works
better on newer cards.
MFhead_mfi r233016
Release driver lock before taking Giant when deleting children.
Use TAILQ_FOREACH_SAFE when items can be deleted. Make code a
little simplier to follow. Fix a couple more style issues.
MFhead_mfi r233620
Update mfi_spare/mfi_array with the actual number of elements
for array_ref and pd. Change these max. #define names to avoid
name space collisions. This will require an update to mfiutil
It avoids mfiutil having to do a magic calculation.
Add a note and #define to state that a "SYSTEM" disk is really
what the firmware calls a "JBOD" drive.
Thanks to the many that helped, LSI for the initial code drop,
mav, delphij, jhb, sbruno that all helped with code and testing.
sys/dev/isci/isci_task_request.c:198:7: error: case value not in enumerated type 'SCI_TASK_STATUS' (aka 'enum _SCI_TASK_STATUS') [-Werror,-Wswitch]
case SCI_FAILURE_TIMEOUT:
^
This is because the switch is done on a SCI_TASK_STATUS enum type, but
the SCI_FAILURE_TIMEOUT value belongs to SCI_STATUS instead.
Because the list of SCI_TASK_STATUS values cannot be modified at this
time, use the simplest way to get rid of this warning, which is to cast
the switch argument to int. No functional change.
Reviewed by: jimharris
MFC after: 3 days
- Do not define the foo_start() methods or set if_start in the ifnet if
multiq transmit is enabled. Also, set if_transmit and if_qflush before
ether_ifattach rather than after when multiq transmit is enabled. This
helps to ensure that the drivers never try to mix different transmit
methods.
- Properly restart transmit during resume. igb(4) was not restarting it
at all, and em(4) was restarting even if the link was down and was
calling the wrong method if multiq transmit was enabled.
- Remove all the 'more' handling for transmit completions. Transmit
completion processing does not have a processing limit, so it always
runs to completion and never has more work to do when it returns.
Instead, the previous code was returning 'true' anytime there were
packets in the queue that weren't still in the process of being
transmitted. The effect was that the driver would continuously
reschedule a task to process TX completions in effect running at 100%
CPU polling the hardware until it finished transmitting all of the
packets in the ring. Now it will just wait for the next TX completion
interrupt.
- Restart packet transmission when the link becomes active.
- Fix the MSI-X queue interrupt handlers to restart packet transmission if
there are pending packets in the relevant software queue (IFQ or buf_ring)
after processing TX completions. This is the root cause for the OACTIVE
hangs as if the MSI-X queue handler drained all the pending packets from
the TX ring, nothing would ever restart it. As such, remove some
previously-added workarounds to reschedule a task to poll the TX ring
anytime OACTIVE was set.
Tested by: sbruno
Reviewed by: jfv
MFC after: 1 week
This change also workarounds dhclient's link state handling bug by
not giving current link status.
Unlike other controllers, ale(4)'s PHY hibernation perfectly works
such that driver does not see a valid link if the controller is not
brought up. If dhclient(8) runs on ale(4) it will blindly waits
until link UP and then gives up after 10 seconds. Because
dhclient(8) still thinks interface got a valid link when IFM_AVALID
is not set for selected media, this change makes dhclient initiate
DHCP without waiting for link UP.
needs to defer link state handling.
While I'm here, mark IFF_DRV_RUNNING before changing media. If
link is established without any delay, that link state change
handling could be lost.
not disable it and it is even harmful as hselasky found out. Historically,
this code was originated from (OLDCARD) CardBus driver and later leaked into
PCI driver when CardBus was newbus'ified and refactored with PCI driver.
However, it is not really necessary even for CardBus.
Reviewed by: hselasky, imp, jhb
bridges. Rather than blindly enabling the windows on all of them, only
enable the window when an MSI interrupt is enabled for a device behind
the bridge, similar to what already happens for HT PCI-PCI bridges.
To implement this, each x86 Host-PCI bridge driver has to be able to
locate it's actual backing device on bus 0. For ACPI, use the _ADR
method to find the slot and function of the device. For the non-ACPI
case, the legacy(4) driver already scans bus 0 looking for Host-PCI
bridge devices. Now it saves the slot and function of each bridge that
it finds as ivars that the Host-PCI bridge driver can then use in its
pcib_map_msi() method.
This fixes machines where non-MSI interrupts were broken by the previous
round of HT MSI changes.
Tested by: bapt
MFC after: 1 week
Right now ath_txq_sched() is mainly called from the TX ath_tx_processq()
routine, which is (mostly) done as part of the taskqueue. It shouldn't
be called outside the taskqueue.
But now that I'm about to flip back on BAR TX, I'm going to start
stressing the ath_tx_tid_pause() and ath_tx_tid_resume() paths.
What I don't want to have happen is a reschedule of the TID traffic
_during_ the completion of TX frames.
Ideally I'd like to have a way to flag back up to the processing code
that the current hardware queue should be rechecked for software TID
queue frames. But for now, this should suffice for the BAR TX case.
I may eventually delete this code once I've brought some further
sanity to the general TX queue/completion path.
Don't disable BARs on any PCI display devices, because doing that can
sometimes cause the main memory bus to stop working, causing all
memory reads to return nothing but 0xFFFFFFFF, even though the memory
location was previously written. After a while a privileged
instruction fault will appear and then nothing more can be debugged.
The reason for this behaviour is unknown.
MFC after: 1 week
New kernel events can be added at various location for sampling or counting.
This will for example allow easy system profiling whatever the processor is
with known tools like pmcstat(8).
Simultaneous usage of software PMC and hardware PMC is possible, for example
looking at the lock acquire failure, page fault while sampling on
instructions.
Sponsored by: NETASQ
MFC after: 1 month
violation should be activated unless the system is cold-booted
after updating EEPROM.
The PCI protocol violation happens only when established link is
10Mbps so the workaround should be updated whenever link state
change is detected. Previously the workaround was activated only
when user checks current media status with ifconfig(8).
whether the checksum of EEPROM is valid or not. Because driver
heavily relies on EEPROM information when it selectively enables
features/workarounds, it would be helpful to know whether driver
sees valid EEPROM.
While I'm here remove all other EEPROM accesses since the entire
EEPROM is loaded at device attach time.
MFC after: 2 weeks
for 82550C. For 82550 controllers this change restores CPUSaver
microcode loading. Due to silicon bug on 82550 and 82550C with
server extension, these controllers seem to require CPUSaver
microcode to receive fragmented UDP datagrams. However the
microcode shouldn't be used on client featured 82550C as it locks
up the controller. In addition, client featured 82550C does not
have the silicon bug. Also clear temporary memory used for
microcode loading since the same memory area is used for other
commands.
While I'm here use 82550C in probe message instead of generic
82550.
Reported by: Andreas Longwitz <longwitz <> incore de>
Tested by: Andreas Longwitz <longwitz <> incore de>
MFC after: 2 weeks
- Make INITAFTERSUSPEND flag independent of HOOKRESUME flag.
- Automatically set INITAFTERSUSPEND flag when ALPS GlidePoint is detected.
- Always probe Synaptics Touchpad. Allow MOUSE_SYN_GETHWINFO ioctl and
automatically set INITAFTERSUSPEND flag when a supported device is detected,
regardless of "hw.psm.synaptics_support" tunable setting.
- Update psm(4) to reflect the above changes.
- Remove long-time defunct SYNCHACK flag while I am in the neighborhood.
MFC after: 1 month
- Do not cover error returned by pmc_core_initialize with the
result of pmc_uncore_initialize, fail right away.
- Give a user something to report instead failing silently
Reported by: Alexandr Kovalenko <never@nevermind.kiev.ua>
The flash commands and responses are little-endian and have to be
byte swapped on big-endian systems. However the raw read of data
need not be swapped.
Make the cfi_read and cfi_write do the swapping, and provide a
cfi_read_raw which does not byte swap for reading data from
flash.
Add a Simple polled driver iicoc for the OpenCores I2C controller. This
is used in Netlogic XLP processors.
Submitted by: Sreekanth M. S. (kanthms at netlogicmicro com)
The earlier version of the driver is sys/mips/rmi/dev/iic/ds1374u.c
Convert all references to ds1374u to ds1374, and use DEVMETHOD_END.
Also update the license header as Netlogic is now Broadcom.
within the BAW.
This regression was introduced in ane earlier commit by me to fix the
BAW seqno allocation-but-not-insertion-into-BAW race. Since it was only
ever using the to-be allocated sequence number, any frame retries
with the first frame in the BAW still in the software queue would
have constantly failed, as ni_txseqs[tid] would always be outside
the BAW.
TODO:
* Extract out the mostly common code here in the agg and non-agg ADDBA
case and stuff it into a single function.
PR: kern/166357
I see traffic stalls.
It turns out that the bug isn't because the first and last frame in the
BAW is in the software queue. It is more likely that it's because
the first frame in the BAW is still in the software queue and thus there's
no more room to allocate and do subsequent TX.
PR: kern/166357
XenServer configurations that advertise the multi-page ring extension,
but only allow a single page of ring space.
sys/dev/xen/blkfront/blkfront.c:
If only one page of ring space is being used, do not publish
in the XenStore the number of pages in use (1), via either
of the supported multi-page ring extension schemes.
Single page operation is the same with or without the
ring-page extension being negotiated. Relying on the
legacy behavior avoids an incompatible difference in how
the two ring-page extension schemes that are out in the
wild, deal with the base case of a single page. The
Amazon/Red Hat drivers use the same XenStore variable as
if the extension was not negotiated. The Citrix drivers
assume the new ring reference XenStore variables will be
available
Reported by: Oliver Schonefeld <schonefeld@ids-mannheim.de>
MFC after: 3 days
This is not entirely correct as it simply resets the channel, flushing
whatever is in the TX/RX queue. This can and will break aggregation
BAW tracking. But the alternative (HT40 frames being sent with the hardware
in HT20 mode) is even worse.
There's still a small window between the htinfo being received (and the ni_chw
field being updated) which could cause problems. I'll look at fleshing this
out in follow-up commits.
PR: kern/166286
order to avoid otherwise harmless witness warnings when these are acquired
at the same time and due to both using MTX_NETWORK_LOCK as their type.
The right fix actually would be to use different, descriptive types for
these. However, the latter would require undesirable changes to the shared
code base. Another approach would be to just supply NULL as the type, which
was deemed as less desirable though as it would cause the unique but cryptic
name also to be used for the type and to diverge from the type used by other
network device drivers.
MFC after: 1 week
Note that this driver additionally probes some device IDs for the most
part not know to other MPT drivers, if at all. So rename the macros not
present in mpi_cnfg.h to match the naming scheme in the latter and but
suffix them with a _FB in order to not cause conflicts.
- Like mpt_set_config_regs(), comment out mpt_read_config_regs() as the
content of the registers read isn't actually used and both functions
aren't exactly up to date regarding the possible layouts of the BARs
(these function might be helpful for debugging though, so don't remove
them completely).
- Use DEVMETHOD_END.
- Use NULL rather than 0 for pointers.
- Remove an unusual check for the softc being NULL.
- Remove redundant zeroing of the softc.
- Remove an overly banal and actually partly incorrect as well as partly
outdated comment regarding the allocation of the memory resource.
MFC after: 3 days
appropriate state handling takes place, not doing so results in the
device doing nothing until manual intervention.
Reviewed by: iwasaki
Tested by: iwasaki (iwi)
MFC after: 4 weeks
until domain discovery is complete. This fixes an isci(4) bug on FreeBSD 7.x
where devices weren't always appearing after boot without an explicit rescan.
Sponsored by: Intel
Reported and tested by: <rpokala at panasas dot com>
Reviewed by: scottl
Approved by: scottl
- Replace MIPS24K-specific code with more generic framework that will
make adding new CPU support easier
- Add MIPS24K support for new framework
- Limit backtrace depth to 1 for stability reasons and add option
HWPMC_MIPS_BACKTRACE to override this limitation
along with functions, SYSCTLs and tunables that are not used with
ATA_CAM in #ifndef ATA_CAM, similar to the existing #ifdef'ed ATA_CAM
code for the other way around. This makes it easier to understand
which parts of ata(4) actually are used in the new world order and
to later on remove the !ATA_CAM bits. It also makes it obvious that
there is something fishy with the C-bus front-end as well as in the
ATP850 support, as these used ATA_LOCKING which is defunct in the
ATA_CAM case. When fixing the former, ATA_LOCKING probably needs to
be brought back in some form or other.
Reviewed by: mav
MFC after: 1 week
is queued to the hardware.
Because multiple concurrent paths can execute ath_start(), multiple
concurrent paths can push frames into the software/hardware TX queue
and since preemption/interrupting can occur, there's the possibility
that a gap in time will occur between allocating the sequence number
and queuing it to the hardware.
Because of this, it's possible that a thread will have allocated a
sequence number and then be preempted by another thread doing the same.
If the second thread sneaks the frame into the BAW, the (earlier) sequence
number of the first frame will be now outside the BAW and will result
in the frame being constantly re-added to the tail of the queue.
There it will live until the sequence numbers cycle around again.
This also creates a hole in the RX BAW tracking which can also cause
issues.
This patch delays the sequence number allocation to occur only just before
the frame is going to be added to the BAW. I've been wanting to do this
anyway as part of a general code tidyup but I've not gotten around to it.
This fixes the PR.
However, it still makes it quite difficult to try and ensure in-order
queuing and dequeuing of frames. Since multiple copies of ath_start()
can be run at the same time (eg one TXing process thread, one TX completion
task/one RX task) the driver may end up having frames dequeued and pushed
into the hardware slightly/occasionally out of order.
And, to make matters more annoying, net80211 may have the same behaviour -
in the non-aggregation case, the TX code allocates sequence numbers
before it's thrown to the driver. I'll open another PR to investigate
this and potentially introduce some kind of final-pass TX serialisation
before frames are thrown to the hardware. It's also very likely worthwhile
adding some debugging code into ath(4) and net80211 to catch when/if this
does occur.
PR: kern/166190
driver is running driver would have already completed flow control
configuration. This change removes unnecessary media changes in
controller reconfiguration cases such that it does not trigger link
reestablishment for configuration change requests like promiscuous
mode change.
Reported by: Many
Tested by: Mike Tancsa <mike <> sentex dot net>
MFC after: 1 week
* printf -> device_printf
* print the buffer pointer and sequence number for any buffer that wasn't
correctly tidied up before it was freed. This is to aid in some
current SMP TX debugging stalls.
PR: kern/166190
For example, some BIOS for AMD SB600 south bridge may map HPET MMIO base
address as a memory BAR for SMBus controller depending on a PM register
configuration. Before r231161 (and r232086, subsequent MFC to stable/9),
it was not fatal but hpet(4) just failed to attach. Since we probe and
attach HPET earlier than PCI devices now, it caused unfortunate hard lockup.
With this patch, it does not hang any more and HPET works at the same time.
Clean up some style nits while I am in the neighborhood.
PR: kern/165647
Reviewed by: jhb
MFC after: 3 days
remaining drivers that haven't been converted have various problems or
complexities that will be dealt with later. This list includes:
hptrr, hptmv, hpt27xx - device aggregation across multiple parents
drm - want to talk to the maintainer first
tsec, sec - Openfirmware devices, not sure if changes are warranted
fatm - Done except for unused testing code
usb - want to talk to the maintainer first
ce, cp, ctau, cx - Significant driver changes needed to convey parent info
There are also devices tucked into architecture subtrees that I'll leave
for the respective maintainers to deal with.
updated.
o Number of times NIC ran out of RX buffer descriptors
o Number of inbound packet errors
o Number of inbound packets that were chosen to be discarded
Previously only the discarded packet counter was used to update
if_ierrors. This change fixes wrong if_ierrors counter on
BCM570[0-4] controllers. For BCM5705 and later controllers bge(4)
already correctly counted it.
Reported by: Eugene Grosbein <egrosbein <> rdtc dot ru>
device in device attach. This would help to narrow down issue to a
specific controller and operating mode of the controller.
While I'm here rename BGE_MISCCFG_BOARD_ID with
BGE_MISCCFG_BOARD_ID_MASK.
AMD-8131 PCI-X bridge. The bridge seems to reorder write access to
mailbox registers such that it caused watchdog timeouts by
out-of-order TX completions.
Tested by: Michael L. Squires <mikes <> siralan dot org >
Reviewed by: jhb
Lower (ISA) IRQs are working, but allowed mask is not set correctly.
Block both by default to allow HP BL465c G6 blade system to boot.
Reported by: Attila Nagy <bra@fsn.hu>
MFC after: 1 week
Although access to the flags to check/set OACTIVE is racy due to how
the default if_start() function works, this should remove any races
with read/modify/write between threads.
don't setup the avp mcast queue.
This is a bit annoying though - it turns out the mcast queue isn't
initialised for STA mode but it's then touched to see whether anything
is in it. That should be fixed in a subsequent commit.
Noticed by: gperez@entel.upc.edu
PR: kern/165895
After 8.0-RELEASE, iwi(4) doesn't send any data frames in infrastructure
mode.
Bacause of the condition `while (frm < efrm)', IEEE80211_VERIFY_LENGTH()
was checking item length beyond the ieee80211_frame region, and returned
from iwi_checkforqos() without setting flags, capinfo and associd.
In infrastructure mode associd is required, so this problem causes
discarding mbuf in ieee80211_start().
PR: kern/165819
Tested/Reviewed/Supported by: bschmidt and adrian
MFC after: 1 week
In a very noisy 2.4GHz environment (with HT/40 enabled, making it worse)
I saw the following occur:
* the air was considered "busy" a lot of the time;
* the cabq time is quite short due to staggered beacons being enabled;
* it just wasn't able to keep up TX'ing CABQ frames;
* .. and the cabq would swallow up all the TX ath_buf's.
This patch introduces a twiddle which allows the maximum cabq depth to be
set, forcing further frames to be dropped.
It defaults to the TX buffer count at the moment, so the default behaviour
isn't changed.
I've also started fleshing out a similar setup for the data path, so
it doesn't swallow up all the available TX buffers and preventing management
frames (such as ADDBA) out.
PR: kern/165895
frames with stations in power saving mode.
I'm not (yet) sure how to handle TX'ing aggregates frames to stations
that are in power saving mode, or whether that's even a feasible thing
to do. So in order to (mostly) not forget, leave a couple of comments
in the code.
The code presently assumes that the aggregation TID state for an ath_node
is locked not by the ath_node lock or a node+TID lock, but behind the
hardware queue said TID maps to. This assumption is going to be
incorrect for stations in power saving mode as we'll be TX'ing frames
on the multicast queue.
In any case, I'm afraid its a "later problem". :/
This function must be called with both the source and destination TXQs
locked or things will get hairy.
I added this as part of some debugging in a PR but it turned out to not
be the cause. I still think it's -correct- so, here it is.
the last buffer in the list.
The current behaviour (due to me, so pointy hat is firmly on my head here)
was incorrect - it was setting the link pointer to the last descriptor
of the _first_ buffer in the TXQ. Instead, it should have set it to the
last descriptor in the _last_ buffer in the TXQ.
This showed up as occasional TX stalls with frames in the TXQ but no
TX progress being made. Further inspection showed the TXQ looked like
it contained multiple "lists" of frames - there'd be a list of correct
frames, then a NULL link pointer, but there'd be a next buffer in the
list.
Since this code is only called upon an interface reset, it's likely
this only began showing up when I started doing stress testing
in environments which annoy the radios enough to cause lockups.
I've not yet any TX stalls with this patch applied.
PR: kern/165866
Expand pci_save_state and pci_restore_state to save more of
the config state for PCI Express and PCI-X devices. Various
writable control registers are present in PCI Express that
can potentially be lost over suspend/resume cycle.
This change is modeled after similar functionality in Linux.
Reviewed by: wlosh,jhb
MFC after: 1 month
all for platforms that only have 32-bit bus addresses. Second, remove
the 'tag_valid' flag from the softc. Instead, if we don't create a
tag in pci_attach_common(), just cache the value of our parent's tag
so that we always have a valid tag to return.
Winbond Super I/O chips.
With minor efforts it should be possible the extend the driver to support
further chips/revisions available from Winbond. In the simplest case
only new IDs need to be added, while different chipsets might require
their own function to enter extended function mode, etc.
Sponsored by: Sandvine Incorporated ULC (in 2011)
Reviewed by: emaste, brueffer
MFC after: 2 weeks
This lets specify whereabouts of the parent PHY for a given MAC node
(and get rid of ugly kludges in mge(4) and tsec(4)).
Obtained from: Semihalf
MFC after: 1 week
- pci_find_extcap() is repurposed to be used for fetching PCI-express
extended capabilities (PCIZ_* constants in <dev/pci/pcireg.h>).
- pci_find_htcap() can be used to locate a specific HyperTransport
capability (PCIM_HTCAP_* constants in <dev/pci/pcireg.h>).
- Cache the starting location of the PCI-express capability for PCI-express
devices in PCI device ivars.
and not asynchronously. This fixes problems related to USB system
suspend and resume. It is assumed that we are always allowed to sleep
from the device_suspend() method.
MFC after: 1 week
Submitted by: jkim
cards that should be handled by the mfi(4) driver.
The root of the problem is that the mpt(4) driver was masking off the
bottom bit of the PCI device ID when deciding which cards to attach to.
It appears that a number of the mpt(4) Fibre Channel cards had a LAN
variant whose PCI device ID was just one bit off from the FC card's device
ID. The FC cards were even and the LAN cards were odd.
The problem was that this pattern wasn't carried over on the SAS and
parallel SCSI mpt(4) cards. Luckily the SAS and parallel SCSI PCI device
IDs were either even numbers, or they would get masked to a supported
adjacent PCI device ID, and everything worked well.
Now LSI is using some of the odd-numbered PCI device IDs between the 3Gb
SAS device IDs for their new MegaRAID cards. This is causing the mpt(4)
driver to attach to the RAID cards instead of the mfi(4) driver.
The solution is to stop masking off the bottom bit of the device ID, and
explicitly list the PCI device IDs of all supported cards.
This change should be a no-op for mpt(4) hardware. The only intended
functional change is that for the 929X, the is_fc variable gets set. It
wasn't being set previously, but needs to be because the 929X is a Fibre
Channel card.
Reported by: Kashyap Desai <Kashyap.Desai@lsi.com>
MFC After: 3 days
The tag enforces a single restriction that all DMA transactions must not
cross a 4GB boundary. Note that while this restriction technically only
applies to PCI-express, this change applies it to all PCI devices as it
is simpler to implement that way and errs on the side of caution.
- Add a softc structure for PCI bus devices to hold the bus_dma tag and
a new pci_attach_common() routine that performs actions common to the
attach phase of all PCI bus drivers. Right now this only consists of
a bootverbose printf and the allocate of a bus_dma tag if necessary.
- Adjust all PCI bus drivers to allocate a PCI bus softc and to call
pci_attach_common() from their attach routines.
MFC after: 2 weeks
interface supported by mvs(4) are 88SX, while AHCI-like chips are 88SE.
PR: kern/165271
Submitted by: Jia-Shiun Li <jiashiun@gmail.com>
MFC after: 1 week
clients.
These are helful when making certain drivers work on both Linux
and FreeBSD without changing the code flow too much.
Reviewed by: kib, wlosh
MFC after: 1 month
pci_cfg_save() and pci_cfg_restore() for device drivers to use when
saving and restoring state (e.g. to handle device-specific resets).
Reviewed by: imp
MFC after: 2 weeks
